INSTALL_2024 - Laserfiche WebLink

Home Browse Search

Initial Setup Of The Console Using Workflow Wizard Setup>Pumps and Lines>PLLD 0.2 gph (0.761ph) Line LeakTest Touch to select the scheduling frequency of the 0.2 gph (0.761ph) periodic tests: Disabled - No manual, repetitive, or monthly 0.2 gph (0.761ph) testing is allowed. This is the default. Repetitive - After a dispense, a 3.0 gph (11.31ph) test is run, followed by a 0.2 gph (0.761ph) test. The test blockout period (the Precision Test Delay in "Setup>Pumps and Lines>AII PLLD") is then observed. Following the test blockout period, the test sequence repeats after the next dispense. NOTE: If the 0.1 gph (0.3 Iph) test is set for Repetitive, this test must also be set to Repetitive. This selection also enables manual 0.2 gph (0.761ph) tests to run when manually started. Monthly -The test is scheduled at the beginning of a new month and remains scheduled until a test is passed. Manual - 0.2 gph (0.761ph) tests run only when manually started in Diagnos- tics> PLLD> Manual Tests Setup>Pumps and Lines>PLLD Low Pressure Shutoff Value If a low pressure is detected during dispense, a low pressure alarm is trig- gered. The dispenser also halts dispensing if the pressure is lower than the value in this field. Allowable selections: 0 to 25 psi (0 to 172kPa) Default: 0.0 Continuous Handle Timeout If the dispenser handle remains off the hook for the period of time entered in this field, the line is shut down by the console. Allowable selections:1 to 16 hours. Default:16 hours Fuel Out Limit If the tank product level is below the limit entered in this field, the Fuel Out Alarm is triggered. Allowable selections: 0.00 to 15.00 in (0.00 to 381.00mm). Default: 10.00 in (254mm). Altitude Pressure Offset 0.1 gph (0.381ph) Line Leak Test I Allows you to set an altitude pressure adjustment for the absolute pressure Touch to select the scheduling frequency of the 0.1 gph (0.381ph) precision transducer of plus or minus 5psi. tests. Allowable selections: -5.0 to 5.0. Default: 0.0. Disabled - No manual or automatic 0.1 gph (0.3 Iph) testing is allowed. This is the default. pump Comm Control Relay Repetitive - After a dispense, a 3.0 gph (11.31ph) test is run, a 0.2 gph (0.761ph) test is run, followed by the 0.1 gph (0.381ph) test. The test blockout period (the Precision Test Delay in "Setup>Pumps and Lines>AII PLLD") is then observed. Following the test blockout period, the test sequence repeats after the next dispense. This selection also enables manual 0.1 gph (0.381ph) testing tests to run when manually started. Auto -The 0.1 gph (0.381ph) test is automatically scheduled to run 6 months after the last passed 0.1 gph (0.381ph) test. This setting also gives you the option to run the Passive 0.1 gph (0.381ph) Line LeakTest. Manual - 0.1 gph (0.381ph) test runs only when manually started in Diagnos- tics> PLLD> Manual Tests. Passive 0.1 gph (0.381ph) Line LeakTest [only available if the pipe type is user -defined and the 0.1 gph (0.381ph) Line LeakTest is set to Auto]. Enables a 0.1 gph (0.381ph) test to run after a passed 0.2 gph (0.761ph) test without the 0.1 gph (0.381ph) test being actively scheduled. If the 0.1 gph (0.381ph) test also passes, you are notified in Diagnostics> PLLD> 0.1 GPH Tests. If it fails, there is no notification of the passive 0.1 gph (0.381ph) test. Allowable selections: Yes, No (default is No). Shutdown Rate The line is shut down if a specified or less precise PLLD test fails. For exam- ple, if you set the shutdown rate for 0.2 gph (0.761ph), the line will shut down if it fails both the 3.0 gph (11.31ph) test and the 0.2 gph (0.761ph) test. Allowable selections: 3.0 gph (11.31ph), 0.2 gph (0.761ph), 0.1gph (0.381ph), or None (default is 3.0 gph (11.31ph). Low Pressure Shutoff If a low pressure is detected during dispense, the Low Pressure Alarm is triggered. The dispenser also halts dispensing if this field is enabled and the pressure is less than the Low Pressure Shutoff Value field below. Allowable selections: Disabled, Enabled (default is Disabled). This relay turns connects/breaks the communication with IQ Control Boxes. It is used during some PLLD tests. When there is pumping on the line in normal operation, the relay is closed and the IQ Control Box can request the assistance from another pump (Helper Mode). The PLLD gross test (3.0 gph/11.3 Iph) is a "pump -off test" so the relay is also closed during this test. However, when a PLLD precision test (0.2 gph/0.76 Iph or 0.1 gph/0.38 Iph test) begins, the relay is opened to prevent the IQ Control Box from request- ing help from another pump while the test is running. The IQ Box must be set to Manual PLLD mode and the relay selected must be set in Setup > Devices (Relays) as a Pump Comm Control relay. M