INSTALL_2024 - Laserfiche WebLink

Home Browse Search

Red Thread TI 11A Piping System (Specification Guide) Section 1 - Scope arewound around a mandrel ata543/;winding angle under controlled tension. Pipe shall be heatcured and the cure shall be This section covers the use of fiberglass reinforced plastic(FRP)pipe for confirmed using a Differential Scanning Calorimeter. single wait fuel handling and fuel hand lingventand vaporapplications including gasoline,unleaded gasoline,gasoline/alcohol mixtures, Pipe shall be supplied with a T.A.B. '(ThreadedandBonded) bio-diesel,DEF and diesel upto150OF and 250psigcyclicpressure. ends. Pipe shall have a minimum continuous cyclic pressure rating of Section 2 - General Conditions 125 prig at 150oF in accordance with ASTM D2992,Procedure A or 2.01 Coordination-Material furnished and work performed underthis UL971 pressure rating. sectionshall be coordinated with the related workand equipment All pipeshall be 100%hydrotested atthe factory beforeshipment specified under othersections,i.e.Valves,Flexible Connectors, at a minimum pressureof 265 psigand shall be UL971-2004 Equipment. Listed and labeled. 2.02 Governing Standards-Exceptas modified orsupplemented 3.02 ASTM D2310 Classifications(at 73.4°F) herein,all materials and construction methods shall complywith and betestedinaccordancewith the followingstandards and test 2"-3" RTRP-11AF methods: 4" RTRP-11AH Standard and Test Methods (Mechanical propertiescell classifications shown are minimums.) 3.03 Fittings-All fittings shall be manufactured usingthesame type UL9712004 Standard for Nonmetallic Underground Piping for Flammable of material as the pipe. Fittings maybe manufactured either by Liquids compression molding,filamentwinding,resin transfer molding ASTMD2310 Standard Classification for Machine-Made"Fiberglass"(Glass Fiber orcontact molding methods. All fittings,adapter,and sump Reinforced Thermosetting Resin) Pipe penetrations shall be UL971-2004 Listed. Standard Test Method for Obtaining Hydrostatic or Pressure Design ssha Fittin shall bonded matched taeredbelland ASTM D2992 Basis for"Fiberglass"(Glass-Fiber-Reinforced-Thermosetting Resin) g p Pipe and Fittings spigot. , 3.04 Connections-Connectionsto flex connectors orother piping 2.03 Operating Conditions-In addition to the above minimum materials shall be made bythe use of NPT(National PipeThread) design requirements,the system shall meet the following threaded adapters orflanges bonded to the FRP piping system. minimum operating conditions: 3.05 Sump Penetrations-Sump penetrations shall be made by a. Operating Pressure means of a permanently bonded FRP coupling. The coupling shall becapable of adjusting forthe slope of the pipingsystem b. Operating Temperature entering or exiting the sump wall. c. Fluid Conveyed 3.06 Adhesives-Adhesives shall be manufacturer's standard forthe piping system specified. d. Test Pressure 2.04QualityAssurance-Pipe manufacturer's quality program shalt Section 3 - Materials and Construction be in compliancewith ISO9001 and/orAPI Q1. 3.012"-4"Primaryand 3"-6"Secondary Pipe-The pipe shall be 2.05 Delivery,Storage and Handling-Pipe and fittingsshallbe manufactured by the filament winding process usingan amine protected from damage due to impact and pointloading. Pipe cured epoxythermosetting resin to impregnate strands of shall be properly supported to avoid damage due to flexural continuous glass filaments,which arewound around a mandrel strain. Thecontractorshall not allow dirt,debris or other at a 543/4"wind i ng angle under controlled tension. Thepipe extraneous materials to get into pipe and fittings. Allfactory shall be heat cured and the cure shall be confirmed using a machined areas shall be protected from sunlight until installed. Differential Scan ni ng Calorimeter. 2.06 Acceptable Manufacturers-Fiber Glass Systems, (501) Pipe shall be supplied with a T.A.B'"(Threaded and Bonded)or 568-4010,or approved equal. plain ends. Pipe shall have a minimum continuous cyclic pressure rating of Section 3 - Materials and Construction 125 psigat150oFin accordance with ASTM D2992,ProcedureAor UL971 pressure rating. 3.012"-4" Pipe-The pipeshallbemanufacturedbythefilament All pipe,both primary and secondary,shall be100%hydrotested winding process using an aminecured epoxy thermosetting at the factory before shipment at a minimum pressureof265 psig resin to impregnate strands of continuous glass filaments,which and shall be UL971-2004 Listed and Labeled. Fiber Glass Systems I KSY ProductionSolutions fgspipe@nov.com nov.com/fgs