COMPLIANCE INFO_2025 - Laserfiche WebLink

Home Browse Search

4.3.5. Recommended method for supplemental heat is to transfer 4.4.7. Joint may take up to 24 hours to cure dependent upon the warm airto the tank sump while keeping ignition sources away. temperature. Allow adhesive to fully cure before moving the joined parts. EZ-FIT ADHESIVE JOINTS (KIT AD E) 4.4. Kit contents:This kit is designed for Adhesive Joints, HAND LAYUP JOINTS (KIT LK) 4.5. Kit Contents: This kit is designed for Hand Layup Joints. Items Size Qty. Items Size Qty. Mix Instructions Sheet(INST6072) 1 Pair Rubber Gloves X-Large 1 SDS for Resin (INST 6070) 1 Plastic Roller 3/4 in.x 3 in. 1 SDS for Hardener(INST 6071) 1 Felt Roller Handle 3 in. 1 Putty Knife 1 Felt Roller Pad 3 in. 2 Resin 1 gal.can 1 Chopped Strand Fiberglass Mat 6 in.W x 33 in.L 15 Hardener 1 qt.can 1 Wooden Mixing Stick 1 Grout Bag 1 Mix Instruction Sheet(INST 6032) 1 Mixing Stick 1 SDS for Resin(ACC 5015)• 1 4.4.1. Read the following instructions completely before applying SDS for Curing Agent(Cadox L-50A-VR) 1 adhesive to EZ-Fit channel (see Figure 4-1). Resin l gal.can 1 4.4.2. Dry fit all tank sump components prior to sealingjoints as Curing Agent 5 gram tubes 15 outlined in Section 3. 4.4.3. Double-wall tank sump adhesive joints include two (2) EZ-Fit 4.5.1. Dry fit all tank sump components prior to sea lingjoints, adhesive channels perjoint, interior and exterior. as outlined in Section 3. 4.4.3.1. 42 in. and 48 in. diameter tank sumps require (1) adhesive 4.5.1.1. Gaps between two joints greater than in. must be kit per channel,totaling two (2) adhesive kits perjoint covered with maximum width 1 in. width tape to (one outside, one inside). prevent resin from running intojoint(See Figure 4-2). 4.4.3.2. 54 in. diametertank sumps require one (1) adhesive kit per interiorchannel and two (2) adhesive kits per exterior Figure 4-2. Layup Joint (Taped) channel,totaling(3) adhesive kits perjoint. Dimensions not 4.4.4. Thoroughly mix two part adhesive by hand or with a power Visually Proportional Tank Sump Body mixerfollowingthe mixing instructions contained in the adhesive kit. Pour into grout bag. t 4.4.5. With the tank sump components in place, fill the adhesive 4 in. Grind/Clean Max 1 in.width tape channel in one 3600 pass (see Figure 4-1). Matingsurface 1/2 in must be used to 4.4.6. When more than one adhesive kit will be required to fill the seal joint gap joint,fill the joint using two or more operators, each starting at the same place and going opposite directions filling the 4in. /zin. joint so the epoxy is uncured when they meet. Grind/Clean Mating Surface Figure 4-1.Adhesive Joint Tank Sump Body Tank Sump/Collar Tank Sump/Collar Exterior —Interior Adhesive Adhesive 4.5.2. The tank sump will be shipped with H-clips for positioning EZ-Fit EZ-Fit the body on the tanks' double-wall collar. With a two (2) piece Adhesive�� Adhesive tank sump,the top is shipped with 8 additional H-clips for Channel Channel positioning the tank sump components. 4.5.3. Double-wall tank sump hand layupjoints include both interior and exterior layups. channel 4.5.3.1. 42 in. and 48 in. diametertank sumps require one (1) Mesh layup kit for the interior layup and one (1) Layup kit for the exterior Layup,totaling two (2) layup kits perjoint. 4.5.3.2. 54 in. diameter tank sumps require two (2) layup kits for Tank Sump/Collar Tank Sump/Collar the interior layup and two (2) layup kits forthe exterior Exterior Interior layup, totaling four(4) layup kits perjoint. 4.5.4. Thoroughly mix resin and hardener following the mixing instructions in the layup kit. nov.com/fgs 5