WORK PLANS - Laserfiche WebLink

Home Browse Search

OPTIONAL PRIMER APPLICATION - OPTIONAL PRIMER - RESUFLOR MPE 1ST BROADCAST COAT sherwin-williams.com/resin-flooringDESIGNED TO PERFORM APPLICATION - 1ST BROADCAST COAT - RESUFLOR MPE COVERAGE RATE: One gallon of RESUFLOR MPE will cover 160 sq. ft. at 10 mils wet/dry film 145 sq. ft. at 11 mils wet/dry film 133 sq ft. at 12 mils wet/dry film 80°F 20 min 80°F 20 min COVERAGE RATE: One gallon of Resuflor MPE will cover: 160 sq. ft. at 10 mils wet/dry film 145 sq. ft. at 11 mils wet/dry film 133 sq. ft. at 12 mils wet/dry film PREMIX PART A using a Jiffy’ mixer blade and slow speed drill (This is required for both 3-gallon and full-filled 5-gallon units.) For full-filled 5 gallon pails, pour out 2 gallons into a measuring container. Then, pour the measured Part A into a mixing pail. ADD RESUFLOR MPE PART B TO PART A (3 GALLONS TOTAL MIX) For full-filled 5-gallon pails, pour out 1 gallon Part B into a measuring container that is separate from the one used with the Part A. Then, add the measured Part B to the Part A already in the mixing pail. POTLIFE: Mix only enough material which can be applied within the work time (time between the addition of Part B to Part A and the completion of all application actions). Check the following chart for work times at various temperatures. For smaller quantities, use 2 parts PART A to 1 part PART B by volume. 90°F 15 min APPLICATION - 1ST BROADCAST COAT - QUARTZ AGGREGATE IMMEDIATELY BROADCAST TO EXCESS WITH DECORATIVE QUARTZ into the uncured Resuflor MPE resin on the floor. Do not dump or pile the material Gently scatter it onto the floor by hand tossing so as to cover the wet resin completely. NOTE: It is important that epoxy is not visible (no wet or shiny areas) after quartz settles because any visible epoxy will yellow. A coverage rate of 0.4 to 0.5 pounds per sq. ft of quartz is recommended ALLOW SYSTEM TO CURE 8-10 hours at 75°F. THOROUGHLY SWEEP AND VACUUM to remove loose colored quartz from surface. NOTE: DO NOT save and reuse swept and vacuumed colored quartz unless you have taken extra precautions. PREMIX PART A using a Jiffy’ mixer blade and slow speed drill. (This is required for both 3-gallon and full-filled 5-gallon units.) For full-filled 5 gallon pails, pour out 2 gallons into a measuring container. Then, pour the measured Part A into a mixing pail. ADD RESUFLOR MPE PART B TO PART A (3 GALLONS TOTAL MIX). For full-filled 5-gallon pails, pour out 1 gallon Part B into a measuring container that is separate from the one used with the Part A. Then, add the measured Part B to the Part A already in the mixing pail POTLIFE: Mix only enough material which can be applied within the work time (time between the addition of Part B to Part A and the completion of all application actions). Check the following chart for work times at various temperatures. For smaller quantities, use 2 parts PART A to 1 part PART B by volume. RESUFLOR DECO QUARTZ DB23 SYSTEM GUIDE 90°F 15 min Sherwin-Williams, MIX FOR 3 MINUTES using a Jiffy’ mixer blade and slow speed drill (Failure to do so could result in lower/dimmished coating properties.) IMMEDIATELY POUR ALL OF THE MIXED MATERIAL onto the floor in a single bead PUSH THE SQUEEGEE at an even speed using downward pressure to apply the desired thickness. A notched squeegee can be used to increase the thickness applied NOTE: The use of spiked shoes will allow freedom of movement on the wet floor CAUTION: The surface will be slippery. START THE SECOND AND REMAINING PASSES by pushing material parallel to the first stroke. Hold the bead of material near the center of the bar and push at an even speed with slight down pressure. BACKROLL THE MATERIAL with a 3/8" nap roller for a smooth uniformed appearance. Backrollmg is required to remove the puddles and squeegee lap marks in order to obtain uniform texture and a consistent mil thickness. MIX FOR 3 MINUTES using a Jiffy' mixer blade and slow speed drill. (Failure to do so could result in lower/diminished coating properties.) IMMEDIATELY POUR ALL OF THE MIXED MATERIAL onto the floor in a single bead PUSH THE SQUEEGEE at an even speed and down pressure to apply the desired thickness A notched squeegee can be used to increase the thickness applied NOTE: The use of spiked shoes will allow freedom of movement on the wet floor CAUTION: The surface will be slippery. START THE SECOND AND REMAINING PASSES by pushing material parallel to the first stroke. Hold the bead of material near the center of the bar and push at an even speed with slight down pressure. BACKROLL THE MATERIAL with a 3/8" nap roller for a smooth uniformed appearance. Backrollmg is required to remove the puddles and squeegee lap marks in order to obtain uniform texture and a consistent mil thickness. APPROXIMATE WORK TIME 65°F 70°F 75°F 40 min 30 min 25 min APPROXIMATE WORK TIME 65°F 70°F 75°F 40 min 30 min 25 min