WORK PLANS - Laserfiche WebLink

Home Browse Search

2ND BROADCAST COAT TOPCOATAPPLICATION - 2ND BROADCAST COAT - RESUFLOR MPE APPLICATION - TOPCOAT- RESUTILE HTS 100 APPLICATION - DECORATIVE QUARTZ REPEAT STEPS used for application of the broadcast quartz GROUT COAT APPLICATION - GROUT COAT - RESUFLOR UVE sherwin-williams.com/resin-flooringDESIGNED TO PERFORM COVERAGE RATE: One gallon of Resuflor MPE will cover 65-70 sq ft./gal at 22-24 mils wet/dry film. REPEAT STEPS used for mixing and spreading of the first seed coat. 75°F 35 mm 80°F 30 min NOTE: The topcoat of Resutile HTS 100 must be applied after the Resuflor UVE has set up enough to walk on and within 24 hours. COVERAGE RATE: A gallon of Resuflor UVE will cover 107 sq. ft. at 15 mils wet/dry film 100 sq. ft. at 16 mils wet/dry film. PREMIX PART A using a Jiffy- mixer blade and slow speed drill Pour out 2 gallons into a measuring container. Then, pour the measured Part A into a mixing pail. ADD RESUFLOR UVE PART B TO PART A (3 GALLONS TOTAL MIX) Pour out 1 gallon Part B into a measuring container that is separate from the one used with the Part A. Then, add the measured Part B to the Part A already in the mixing pail. POTLIFE: Mix only enough material which can be applied within the work time (time betv/een the addition of Part B to Part A and the completion of all application actions). Check the following chart for work times at various temperatures For smaller quantities, use 2 parts PART A to 1 part PART B by volume. APPROXIMATE WORK TIME 65°F 70°F 50 min 40 min 90°F 25 min SPREAD THE MATERIAL evenly with V-shaped cross passes MAKE SURE THE FLOOR HAS JUST ENOUGH COATING TO COVER EVENLY. Excess material could cause the floor to blister, especially in high humidity. Insufficient material will cause the floor to look non-uniform. LEVEL THE AREA with straight passes that cross the initial material paths. These final strokes will reduce roller marks. If the appearance is not satisfactory, reroll the area. REMIX THE MATERIAL in the tray occasionally (with the roller) to prevent settling of the Part C (filler). NOTE: When multiple applicators are used to apply material, inconsistencies between areas may result. To ensure a more uniform finish, an individual outfitted with spike shoes may finish by pushing or pulling a roller across all applicator areas ALLOW COATING TO DRY 24 HOURS at 75°F, 50% relative humidity before opening to light traffic. Allow more time at low temperatures, low humidity or for heavier traffic. Full coating properties take 14 days to develop. POUR PART C INTO PART A while mixing CONTINUE TO MIX AND ADD PART B RESUFLOR DECO QUARTZ DB23 SYSTEM GUIDE MIX FOR 3 MINUTES using a Jiffy' mixer blade and slow speed drill Pour into application tray. APPLY RESUTILE HTS 100 at the rate of 535 sq.ft./gal with a 3/8" nap roller. For proper appearance and development of physical properties, it is crucial that material is not applied above or below this rate. Dip the roller in the coating and lightly roll out excess in the application tray. Apply two 8-10-ft.-long paths on the concrete, making one stroke left to right and one right to left. Rewet the roller and apply two more paths adjacent to the first pair. Rewet roller and apply a third pair adjacent to the second. PREMIX PART A FOR 3 MINUTES USING A JIFFY' MIXER BLADE with slow speed drill. POTLIFE: Mix only enough material which can be used in a two-hour period. NOTE: Once opened, this material cannot be resealed for later use. Sherwin-Williams. MIX FOR 2 MINUTES using a Jiffy' mixer blade and slow speed drill. (Failure to do so could result in lower/dimmished coating properties.) IMMEDIATELY POUR ALL OF THE MIXED MATERIAL onto the floor in a single bead PUSH THE FLAT SQUEEGEE at an even speeo with sufficient down pressure to apply the thinnest coat NOTE: The use of spiked shoes will allow freedom of movement on the wet floor. START THE SECOND AND REMAINING PASSES by pushing material parallel to the first stroke Hold the bead of material near the center of the bar. BACKROLL THE MATERIAL with a 3/8" nap roller for a smooth uniformed appearance. Backrolhng is required to remove the puddles and squeegee lap marks in order to obtain uniform texture and a consistent mil thickness. NOTE: Get off the Resuflor UVE as soon as possible. Resuflor UVE must be topcoated with Resutile HTS 100 at floor temperatures of 65-90°F within 24 hours.