Laserfiche WebLink
LXeR <br />advansgs HOT <br />9 7/16" <br />23 15/16” <br />El <br />PI <br />Ml <br />> <br />32 15/16" <br />1 1/16" — <br />26 3/4" <br />44 11/16" <br />| A WARNING]VOLTS/HERTZ/PHASEMODEL <br />208-240/60/1 30.5 40 40 <br />120/208-240(3W)/60/r 4030.5 40 <br />208-240/60/3 23.9 30 30 <br />40220-240/50/1 30.5 40 <br />Page 2 of 4 <br />NOTE: FOR SUPPLY CONNECTIONS, USE COPPER WIRE ONLY RATED AT 90”C MINIMUM. <br />• THIS SYSTEM REQUIRES THREE POWER WIRES WHICH INCLUDES A CURRENT CARRYING <br />NEUTRAL, AN ADDITIONAL FOURTH WIRE MUST BE PROVIDED FOR MACHINE GROUND. <br />ACCESSORY CORD KIT AVAILABLE FOR ALL MACHINES <br />DETERGENT & <br />RINSE-AID <br />ADDITIONAL CLEARANCE REQUIRED TO <br />SLIDE UNIT FORWARD FOR SERVICE ONLY <br />RATED <br />AMPS <br />MIN SUPPLY <br />CKT CONDUCTOR <br />AMPACITY <br />TRIM STRIP <br />(OPTIONAL) <br />PROTECTIVE <br />DEVICE <br />39 1/2“ <br />SERVICE <br />CLEARANCE <br />MIN. <br />Plumbing connections must comply with <br />applicable sanitary, safety and plumbing <br />codes. Drain and fill line configurations <br />vary, some methods are shown on this drawing. <br />MODELS: <br />LXeR <br />00-947872 <br />REVC <br />17" <br />MAX. <br />LOADING <br />HEIGHT <br />I <br />^HOBART/ <br />701 S Ridge Avenue, Troy, OH 45374 <br />1-888-4HOBART •www.hobartcorp.com <br />IZL <br />RECOMMENDED <br />17“ OR LESS <br />I <br />MODEL <br />LXeR <br />HEAT OUTPUT, BTU/HR <br />LATENT <br />1100 <br />SENSIBLE <br />2000 <br />SHIPPING WEIGHTS________ <br />NET WEIGHT OF MACHINE <br />DOMESTIC SHIPPING WEIGHT <br />LXeR <br />165 LBS <br />185 LBS <br />,----- 1-1/2" TRADE SIZE <br />\ PIPE MIN. REDUCED <br />\ DOWN TO 3/4" FPT <br />\ CONNECTION (BY <br />32 1/2" i £4— CHEMICAL BOTTLES <br />MAY BE LOCATED ON <br />EITHER SIDE OF MACHINE <br />Electrical and grounding connections <br />must comply with the applicable portions <br />of the National Electrical Code and/or <br />other local electrical codes. <br />I NOTICE | <br />Required flowing water pressure to the dishmachine is 15-65 PSIG. If <br />pressures higher than 65 PSIG are present, a pressure regulating valve <br />must be installed in the water line to the dishmachine (by others). <br />Pressure gauge not required on pumped rinse machines. <br />If chemical containers are to be placed in cabinet adjacent to machine, <br />a 1/2" dia. hole is required in the cabinet to run chemical supply line. <br />Notes: <br />1. All vertical machine dimensions taken from floor may be increased <br />by 1". <br />2. Moist air escapes from the door. <br />Use only moisture resistant materials adjacent to dishmachine <br />sides and top. <br />3. A vent hood is not recommended above the undercounter dishmachine <br />since it does not produce excessive vapors. <br />4. A SS-BO-F incoming cold water connection Is recommended for the LXeR. <br />Plumbing notes: <br />1. Water hammer arrestor (meeting ASSE-1010 Standard or equivalent) <br />to be supplied (by others) in common water supply line at service <br />connection. <br />2. Recommended water hardness to be 3 grains or less for best results. <br />/3?\lf drain hose Is looped above a sink, the loop must not exceed 38" AFF. <br />ELECTRICAL CONNECTION: 1-3/8" DIA. HOLE FOR <br />1" TRADE SIZE CONDUIT; 4-5/8" AFF. <br />SINGLE FILL AND RINSE CONNECTION: 3/4" FEMALE <br />GARDEN HOSE FITTING ON 6' LONG HOSE SUPPUED <br />WITH MACHINE.; <br />55-80oF (COLD) RECOMMENDED FOR LXeR. <br />P2 DRAIN CONNECTION: 5/8" BARB FITTING WITH <br />6' LONG HOSE SUPPLIED WITH MACHINE. <br />CONNECTION INFORMATION <br />(AFF = ABOVE FINISHED FLOOR) <br />LEGEND <br />10 9/16" <br />; A KJS) d—------- <br />/ RECOMMENDED WATER <br />z--< —1r-----W6 SERVICE ROUGH-IN <br />(El) L___??s/lfi"_____J 1/2" TRADE SIZE <br />r n PIPE MIN. W/SHUTOFF <br />VALVE, LINE STRAINER <br />& 3/4" MALE GARDEN <br />HOSE FITTING (BY <br />CUSTOMER). <br />(COLD WATER) <br />DELIMER <br />(ADDITIONAL x <br />CLEARANCE <br />MAY BE <br />REQUIRED) <br />F40336 - LXeR and LXePR advansds Hot and Cold <br />15186 <br />LXeR I <br />El <br />P2 <br />9" . <br />MIN. <br />P2) (PI