|
5.504.4.3 Paints and coatings. Architectural paints and coatings shall comply with VOC limits in Table 1 of
<br />the ARB Architectural Coatings Suggested Control Measure, as shown in Table 5.504.4.3, unless more
<br />stringent local limits apply. The VOC content limit for coatings that do not meet the definitions for the specialty
<br />coatings categories listed in Table 5.504.4.3 shall be determined by classifying the coating as a Flat, Nonflat
<br />or Nonflat-High Gloss coating, based on its gloss, as defined in Subsections 4.21, 4.36 and 4.37 of the 2007
<br />California Air Resources Board Suggested Control Measure, and the corresponding Flat, Nonflat or
<br />Nonflat-High Gloss VOC limit in Table 5.504.4.3 shall apply.
<br />5.504.4.3.1 Aerosol Paints and coatings. Aerosol paints and coatings shall meet the PWMIR Limits for
<br />ROC in Section 94522(a)(3) and other requirements, including prohibitions on use of certain toxic
<br />compounds and ozone depleting substances, in Sections 94522(c)(2) and (d)(2) of California Code of
<br />Regulations, Title 17, commencing with Section 94520; and in areas under the jurisdiction of the
<br />Bay Area Air Quality Management District additionally comply with the percent VOC by weight of product
<br />limits of Regulation 8 Rule 49.
<br />5.504.4.5 Composite wood products. Hardwood plywood, particleboard and medium density fiberboard
<br />composite wood products used on the interior or exterior of the buildings shall meet the requirements for
<br />formaldehyde as specified in ARB's Air Toxics Control Measure (ATCM) for Composite Wood (17 CCR 93120 et
<br />seq.). Those materials not exempted under the ATCM must meet the specified emission limits, as shown in
<br />Table 5.504.4.5.
<br />5.504.4.5.3 Documentation. Verification of compliance with this section shall be provided as
<br />requested by the enforcing agency. Documentation shall include at least one of the following:
<br />1. Product certifications and specifications.
<br />2. Chain of custody certifications.
<br />3. Product labeled and invoiced as meeting the Composite Wood Products regulation (see
<br /> CCR, Title 17, Section 93120, et seq.).
<br />4. Exterior grade products marked as meeting the PS-1 or PS-2 standards of the
<br /> Engineered Wood Association, the Australian AS/NZS 2269 or European 636 3S
<br /> standards.
<br />5. Other methods acceptable to the enforcing agency.
<br />SPECIALTY COATINGS
<br />ALUMINUM ROOF COATINGS 400
<br />BASEMENT SPECIALTY COATINGS 400
<br />BITUMINOUS ROOF COATINGS 50
<br />BITUMINOUS ROOF PRIMERS 350
<br />BOND BREAKERS 350
<br />CONCRETE CURING COMPOUNDS 350
<br />CONCRETE/MASONRY SEALERS 100
<br />DRIVEWAY SEALERS 50
<br />DRY FOG COATINGS 150
<br />FAUX FINISHING COATINGS 350
<br />FIRE RESISTIVE COATINGS 350
<br />FLOOR COATINGS 100
<br />FORM-RELEASE COMPOUNDS 250
<br />GRAPHIC ARTS COATINGS (SIGN PAINTS)500
<br />HIGH-TEMPERATURE COATINGS 420
<br />INDUSTRIAL MAINTENANCE COATINGS 250
<br />LOW SOLIDS COATINGS1 120
<br />MAGNESITE CEMENT COATINGS 450
<br />MASTIC TEXTURE COATINGS 100
<br />METALLIC PIGMENTED COATINGS 500
<br />MULTICOLOR COATINGS 250
<br />PRETREATMENT WASH PRIMERS 420
<br />PRIMERS, SEALERS, & UNDERCOATERS 100
<br />REACTIVE PENETRATING SEALERS 350
<br />RECYCLED COATINGS 250
<br />ROOF COATINGS 50
<br />RUST PREVENTATIVE COATINGS 250
<br />SHELLACS:
<br />CLEAR 730
<br />OPAQUE 550
<br />SPECIALTY PRIMERS, SEALERS & UNDERCOATERS 100
<br />STAINS 250
<br />STONE CONSOLIDANTS 450
<br />SWIMMING POOL COATINGS 340
<br />TRAFFIC MARKING COATINGS 100
<br />TUB & TILE REFINISH COATINGS 420
<br />WATERPROOFING MEMBRANES 250
<br />WOOD COATINGS 275
<br />WOOD PRESERVATIVES 350
<br />ZINC-RICH PRIMERS 340
<br />1. GRAMS OF VOC PER LITER OF COATING, INCLUDING WATER & EXEMPT COMPOUNDS
<br />2. THE SPECIFIED LIMITS REMAIN IN EFFECT UNLESS REVISED LIMITS ARE LISTED IN SUBSEQUENT COLUMNS
<br />IN THE TABLE.
<br />3. VALUES IN THIS TABLE ARE DERIVED FROM THOSE SPECIFIED BY THE CALIFORNIA AIR RESOURCES BOARD,
<br />ARCHITECTURAL COATINGS SUGGESTED CONTROL MEASURE, FEB. 1, 2008. MORE INFORMATION IS
<br />AVAILABLE FROM THE AIR RESOURCES BOARD.
<br />TABLE 5.504.4.5 - FORMALDEHYDE LIMITS1
<br />MAXIMUM FORMALDEHYDE EMISSIONS IN PARTS PER MILLION
<br />PRODUCT CURRENT LIMIT
<br />HARDWOOD PLYWOOD VENEER CORE 0.05
<br />HARDWOOD PLYWOOD COMPOSITE CORE 0.05
<br />PARTICLE BOARD 0.09
<br />MEDIUM DENSITY FIBERBOARD 0.11
<br />THIN MEDIUM DENSITY FIBERBOARD2 0.13
<br />1. VALUES IN THIS TABLE ARE DERIVED FROM THOSE SPECIFIED BY THE CALIFORNIA AIR RESOURCES BOARD, AIR
<br />TOXICS CONTROL MEASURE FOR COMPOSITE WOOD AS TESTED IN ACCORDANCE WITH ASTM E 1333. FOR
<br />ADDITIONAL INFORMATION, SEE CALIFORNIA CODE OF REGULATIONS, TITLE 17, SECTIONS 93120 THROUGH 93120.12.
<br />2. THIN MEDIUM DENSITY FIBERBOARD HAS A MAXIMUM THICKNESS OF 5/16 INCHES (8 MM).
<br />5.508.2.6 Evacuation. The system shall be evacuated after pressure testing and prior to charging.
<br />5.508.2.6.1 First vacuum. Pull a system vacuum down to at least 1000 microns (+/- 50 microns), and
<br />hold for 30 minutes.
<br />5.508.2.6.2 Second vacuum. Pull a second system vacuum to a minimum of 500 microns and hold for 30
<br />minutes.
<br />5.508.2.6.3 Third vacuum. Pull a third vacuum down to a minimum of 300 microns, and hold for 24 hours
<br />with a maximum drift of 100 microns over a 24-hour period.
<br />CHAPTER 7
<br />INSTALLER & SPECIAL INSPECTOR QUALIFICATIONS
<br />702 QUALIFICATIONS
<br />702.1 INSTALLER TRAINING. HVAC system installers shall be trained and certified in the proper
<br />installation of HVAC systems including ducts and equipment by a nationally or regionally recognized training or
<br />certification program. Uncertified persons may perform HVAC installations when under the direct supervision and
<br />responsibility of a person trained and certified to install HVAC systems or contractor licensed to install HVAC systems.
<br />Examples of acceptable HVAC training and certification programs include but are not limited to the following:
<br />1. State certified apprenticeship programs.
<br />2. Public utility training programs.
<br />3. Training programs sponsored by trade, labor or statewide energy consulting or verification organizations.
<br />4. Programs sponsored by manufacturing organizations.
<br />5. Other programs acceptable to the enforcing agency.
<br />702.2 SPECIAL INSPECTION [HCD]. When required by the enforcing agency, the owner or the
<br />responsible entity acting as the owner's agent shall employ one or more special inspectors to provide inspection or
<br />other duties necessary to substantiate compliance with this code. Special inspectors shall demonstrate competence
<br />to the satisfaction of the enforcing agency for the particular type of inspection or task to be performed. In addition to
<br />other certifications or qualifications acceptable to the enforcing agency, the following certifications or education may be
<br />considered by the enforcing agency when evaluating the qualifications of a special inspector:
<br />1. Certification by a national or regional green building program or standard publisher.
<br />2. Certification by a statewide energy consulting or verification organization, such as HERS raters, building
<br /> performance contractors, and home energy auditors.
<br />3. Successful completion of a third party apprentice training program in the appropriate trade.
<br />4. Other programs acceptable to the enforcing agency.
<br />Notes:
<br />1. Special inspectors shall be independent entities with no financial interest in the materials or the
<br />project they are inspecting for compliance with this code.
<br />2. HERS raters are special inspectors certified by the California Energy Commission (CEC) to rate
<br />homes in California according to the Home Energy Rating System (HERS).
<br />[BSC-CG] When required by the enforcing agency, the owner or the responsible entity acting as the owner's agent
<br />shall employ one or more special inspectors to provide inspection or other duties necessary to substantiate
<br />compliance with this code. Special inspectors shall demonstrate competence to the satisfaction of the enforcing
<br />agency for the particular type of inspection or task to be performed. In addition, the special inspector shall have a
<br />certification from a recognized state, national or international association, as determined by the local agency. The
<br />area of certification shall be closely related to the primary job function, as determined by the local agency.
<br />Note: Special inspectors shall be independent entities with no financial interest in the materials or the
<br />project they are inspecting for compliance with this code.
<br />703 VERIFICATIONS
<br />703.1 DOCUMENTATION. Documentation used to show compliance with this code shall include but is not limited to,
<br />construction documents, plans, specifications, builder or installer certification, inspection reports, or other methods
<br />acceptable to the enforcing agency which demonstrate substantial conformance. When specific documentation or
<br />special inspection is necessary to verify compliance, that method of compliance will be specified in the appropriate
<br />section or identified applicable checklist.
<br />2022 CALIFORNIA GREEN BUILDING STANDARDS CODE
<br />NONRESIDENTIAL MANDATORY MEASURES, SHEET 4 (July 2024 Supplement)
<br />SECTION 5.505 INDOOR MOISTURE CONTROL
<br />5.505.1 INDOOR MOISTURE CONTROL. Buildings shall meet or exceed the provisions of California Building Code,
<br />CCR, Title 24, Part 2, Sections 1202 (Ventilation) and Chapter 14 (Exterior Walls). For additional measures, see
<br />Section 5.407.2 of this code.
<br />SECTION 5.506 INDOOR AIR QUALITY
<br />5.506.1 OUTSIDE AIR DELIVERY. For mechanically or naturally ventilated spaces in buildings, meet the minimum
<br />requirements of Section 120.1 (Requirements For Ventilation) of the California Energy Code, or the applicable local
<br />code, whichever is more stringent, and Division 1, Chapter 4 of CCR, Title 8.
<br />5.506.2 CARBON DIOXIDE (CO2) MONITORING. For buildings or additions equipped with demand control
<br />ventilation, CO2 sensors and ventilation controls shall be specified and installed in accordance with the requirements
<br />of the California Energy Code, Section 120(c)(4).
<br />5.506.3 Carbon dioxide (CO2) monitoring in classrooms.
<br />(DSA-SS) Each public K-12 school classroom, as listed in Table 120.1-A of the California Energy Code, shall be
<br />equipped with a carbon dioxide monitor or sensor that meets the following requirements:
<br />1.The monitor or sensor shall be permanently affixed in a tamper-proof manner in each classroom between 3 and
<br />6 feet (914 mm and 1829 mm) above the floor and at least 5 feet (1524 mm) away from door and operable
<br />windows.
<br />2.When the monitor or sensor is not integral to an Energy Management Control System (EMCS), the monitor or
<br />sensor shall display the carbon dioxide readings on the device. When the sensor is integral to an EMCS, the
<br />carbon dioxide readings shall be available to and regularly monitored by facility personnel.
<br />3.A monitor shall provide notification though a visual indicator on the monitor when the carbon dioxide levels in the
<br />classroom have exceeded 1,100ppm. A sensor integral to an EMCS shall provide notification to facility
<br />personnel through a visual and/or audible indicator when the carbon dioxide levels in the classroom have
<br />exceeded 1,100ppm.
<br />4.The monitor or sensor shall measure carbon dioxide levels at minimum 15- minute intervals and shall maintain a
<br />record of previous carbon dioxide measurements of not less than 30 days duration.
<br />5.The monitor or sensor used to measure carbon dioxide levels shall have the capacity to measure carbon dioxide
<br />levels with a range of 400ppm to 2000ppm or greater.
<br />6.The monitor or sensor shall be certified by the manufacturer to be accurate within 75ppm at 1,000ppm carbon
<br />dioxide concentration and shall be certified by the manufacturer to require calibration no more frequently than
<br />once every 5 years.
<br />SECTION 5.507 ENVIRONMENTAL COMFORT
<br />5.507.4 ACOUSTICAL CONTROL. Employ building assemblies and components with Sound Transmission Class
<br />(STC) values determined in accordance with ASTM E 90 and ASTM E 413, or Outdoor-Indoor Sound Transmission
<br />Class (OITC) determined in accordance with ASTM E 1332, using either the prescriptive or performance method in
<br />Section 5.507.4.1 or 5.507.4.2.
<br />Exception: Buildings with few or no occupants or where occupants are not likely to be affected by exterior
<br />noise, as determined by the enforcement authority, such as factories, stadiums, storage, enclosed parking
<br />structures and utility buildings.
<br />Exception: [DSA-SS] For public schools and community colleges, the requirements of this section and all
<br />subsections apply only to new construction.
<br />5.507.4.1 Exterior noise transmission, prescriptive method. Wall and roof-ceiling assemblies exposed to
<br />the noise source making up the building or addition envelope or altered envelope shall meet a composite STC
<br />rating of at least 50 or a composite OITC rating of no less than 40, with exterior windows of a minimum STC of
<br />40 or OITC of 30 in the following locations:
<br />1. Within the 65 CNEL noise contour of an airport.
<br />Exceptions:
<br />1. Ldn or CNEL for military airports shall be determined by the facility Air Installation Compatible
<br /> Land Use Zone (AICUZ) plan.
<br />2. Ldn or CNEL for other airports and heliports for which a land use plan has not been developed
<br /> shall be determined by the local general plan noise element.
<br />2. Within the 65 CNEL or Ldn noise contour of a freeway or expressway, railroad, industrial source or
<br /> fixed-guideway source as determined by the Noise Element of the General Plan.
<br />5.507.4.1.1. Noise exposure where noise contours are not readily available. Buildings exposed to a
<br />noise level of 65 dB Leq - 1-hr during any hour of operation shall have building, addition or alteration
<br />exterior wall and roof-ceiling assemblies exposed to the noise source meeting a composite STC rating of
<br />at least 45 (or OITC 35), with exterior windows of a minimum STC of 40 (or OITC 30).
<br />5.507.4.2 Performance Method. For buildings located as defined in Section 5.507.4.1 or 5.507.4.1.1, wall and
<br />roof-ceiling assemblies exposed to the noise source making up the building or addition envelope or altered
<br />envelope shall be constructed to provide an interior noise environment attributable to exterior sources that does
<br />not exceed an hourly equivalent noise level (Leq-1Hr) of 50 dBA in occupied areas during any hour of operation.
<br />5.507.4.2.1 Site Features. Exterior features such as sound walls or earth berms may be utilized as
<br />appropriate to the building, addition or alteration project to mitigate sound migration to the interior.
<br />5.507.4.2.2 Documentation of Compliance. An acoustical analysis documenting complying interior
<br />sound levels shall be prepared by personnel approved by the architect or engineer of record.
<br />5.507.4.3 Interior sound transmission. Wall and floor-ceiling assemblies separating tenant spaces and tenant
<br />spaces and public places shall have an STC of at least 40.
<br />Note: Examples of assemblies and their various STC ratings may be found at the California Office of
<br />Noise Control: www.toolbase.org/PDF/CaseStudies/stc_icc_ratings.pdf.
<br />SECTION 5.508 OUTDOOR AIR QUALITY
<br />5.508.1 Ozone depletion and greenhouse gas reductions. Installations of HVAC, refrigeration and fire suppression
<br />equipment shall comply with Sections 5.508.1.1 and 5.508.1.2.
<br />5.508.1.1 Chlorofluorocarbons (CFCs). Install HVAC, refrigeration and fire suppression equipment that do not
<br />contain CFCs.
<br />5.508.1.2 Halons. Install HVAC, refrigeration and fire suppression equipment that do not contain Halons.
<br />5.508.2 Supermarket refrigerant leak reduction. New commercial refrigeration systems shall comply with the
<br />provisions of this section when installed in retail food stores 8,000 square feet or more conditioned area, and that
<br />utilize either refrigerated display cases, or walk-in coolers or freezers connected to remote compressor units or
<br />condensing units. The leak reduction measures apply to refrigeration systems containing high-global-warming potential
<br />(high-GWP) refrigerants with a GWP of 150 or greater. New refrigeration systems include both new facilities and the
<br />replacement of existing refrigeration systems in existing facilities.
<br />Exception: Refrigeration systems containing low-global warming potential (low-GWP) refrigerant with a GWP
<br />value less than 150 are not subject to this section. Low-GWP refrigerants are nonozone-depleting refrigerants
<br />that include ammonia, carbon dioxide (CO2), and potentially other refrigerants.
<br />5.508.2.1 Refrigerant piping. Piping compliant with the California Mechanical Code shall be installed to be
<br />accessible for leak protection and repairs. Piping runs using threaded pipe, copper tubing with an outside
<br />diameter (OD) less than 1/4 inch, flared tubing connections and short radius elbows shall not be used in
<br />refrigerant systems except as noted below.
<br />5.508.2.1.1 Threaded pipe. Threaded connections are permitted at the compressor rack.
<br />5.508.2.1.2 Copper pipe. Copper tubing with an OD less than 1/4 inch may be used in systems with a
<br />refrigerant charge of 5 pounds or less.
<br />5.508.2.1.2.1 Anchorage. One-fouth-inch OD tubing shall be securely clamped to a rigid base to
<br />keep vibration levels below 8 mils.
<br />5.508.2.1.3 Flared tubing connections. Double-flared tubing connections may be used for pressure
<br />controls, valve pilot lines and oil.
<br />Exception: Single-flared tubing connections may be used with a multiring seal coated with
<br />industrial sealant suitable for use with refrigerants and tightened in accordance with manufacturer's
<br />recommendations.
<br />5.508.2.1.4 Elbows. Short radius elbows are only permitted where space limitations prohibit use of
<br />long radius elbows.
<br />5.508.2.2 Valves. Valves Valves and fittings shall comply with the California Mechanical Code and as
<br />follows.
<br />5.508.2.2.1 Pressure relief valves. For vessels containing high-GWP refrigerant, a rupture disc shall
<br />be installed between the outlet of the vessel and the inlet of the pressure relief valve.
<br />5.508.2.2.1.1 Pressure detection. A pressure gauge, pressure transducer or other device shall
<br />be installed in the space between the rupture disc and the relief valve inlet to indicate a disc
<br />rupture or discharge of the relief valve.
<br />5.508.2.2.2 Access valves. Only Schrader access valves with a brass or steel body are
<br />permitted for use.
<br />5.508.2.2.2.1 Valve caps. For systems with a refrigerant charge of 5 pounds or more, valve caps
<br />shall be brass or steel and not plastic.
<br />5.508.2.2.2.2 Seal caps. If designed for it, the cap shall have a neoprene O-ring in place.
<br />5.508.2.2.2.2.1 Chain tethers. Chain tethers to fit ovr the stem are required for valves
<br />designed to have seal caps.
<br />Exception: Valves with seal caps that are not removed from the valve during stem
<br />operation.
<br />5.508.2.3 Refrigerated service cases. Refrigerated service cases holding food products containing vinegar and
<br />salt shall have evaporator coils of corrosion-resistant material, such as stainless steel; or be coated to prevent
<br />corrosion from these substances.
<br />5.508.2.3.1 Coil coating. Consideration shall be given to the heat transfer efficiency of coil coating to
<br />maximize energy efficiency.
<br />5.508.2.4 Refrigerant receivers. Refrigerant receivers with capacities greater than 200 pounds shall be fitted
<br />with a device tha indicates the level of refrigerant in the receiver.
<br />5.508.2.5 Pressure testing. The system shall be pressure tested during installation prior to evacuation and
<br />charging.
<br />5.508.2.5.1 Minimum pressure. The system shall be charged with regulated dry nitrogen and
<br />appropriate tracer gas to bring system pressure up to 300 psig minimum.
<br />5.508.2.5.2 Leaks. Check the system for leaks, repair any leaks, and retest for pressure using the same
<br />gauge.
<br />5.508.2.5.3 Allowable pressure change. The system shall stand, unaltered, for 24 hours with no more
<br />than a +/- one pound pressure change from 300 psig, measured with the same gauge.
<br />5.504.4.6 Resilient flooring systems. Where resilient flooring is installed, at least 80 percent of floor area
<br />receiving resilient flooring shall meet the requirements of the California Department of Public Health,"Standard
<br />Method for the Testing and Evaluation of Volatile Organic Chemical Emissions from Indoor Sources Using
<br />Environmental Chambers," Version 1.2, January 2017 (Emission testing method for California Specifications
<br />01350)
<br />See California Department of Public Health's website for certification programs and testing labs.
<br />https://www.cdph.ca.gov/Programs/CCDPHP/DEODC/EHLB/IAQ/Pages/VOC.aspx#material
<br />5.504.4.6.1 Verification of compliance. Documentation shall be provided verifying that resilient flooring
<br />materials meet the pollutant emission limits.
<br />5.504.4.7 Thermal insulation
<br />Comply with the requirements of the California Department of Public Health, "Standard Method of the Testing
<br />and Evaluation of Volatile Organic Chemical Emissions from Indoor Sources Using Environmental Chambers,
<br />"Version 1.2, January 1.2, January 2017 (Emission testing method for California Specification 01350).
<br />See California Department of Public Health's website for certification programs and testing labs.
<br />https://www.cdph.ca.gov/Programs/CCDPHP/DEODC/EHLB/IAQ/Pages/VOC.aspx#material
<br />5.504.4.7.1 Verification of compliance.
<br />Documentation shall be provided verifying that thermal insulation materials meet the pollutant emission
<br />limits.
<br />5.504.4.8 Acoustical ceiling and wall panels.
<br />Comply with the requirements of the California Department of Public Health, "Standard Method for the Testing
<br />and Evaluation of Volatile Organic Chemical Emissions from Indoor Sources Using Environmental Chambers, "
<br />Version 1.2, January 2017 (Emission testing method for California Specification 01350).
<br />See California Department of Public Health's website for certification programs and testing labs.
<br />5.504.4.8.1 Verification of compliance. Documentation shall be provided verifying that acoustical
<br /> finish materials meet the pollutant emission limits.
<br />5.504.5.3 Filters. In mechanically ventilated buildings, provide regularly occupied areas of the building with air
<br />filtration media for outside and return air that provides at least a Minimum Efficiency Reporting Value (MERV) of
<br />13. MERV 13 filters shall be installed prior to occupancy, and recommendations for maintenance with filters of
<br />the same value shall be included in the operation and maintenance manual.
<br />Exceptions: Existing mechanical equipment.
<br /> 5.504.5.3.1 Labeling. Installed filters shall be clearly labeled by the manufacturer indicating the MERV
<br /> rating.
<br />5.504.7 ENVIRONMENTAL TOBACCO SMOKE (ETS) CONTROL. Where outdoor areas are provided for smoking,
<br />prohibit smoking within 25 feet of building entries, outdoor air intakes and operable windows and within the building as
<br />already prohibited by other laws or regulations; or as enforced by ordinances, regulations or policies of any city,
<br />county, city and county, California Community College, campus of the California State University, or campus of the
<br />University of California, whichever are more stringent. When ordinances, regulations or policies are not in place, post
<br />signage to inform building occupants of the prohibitions.
<br />5.504.4.3.2 Verification. Verification of compliance with this section shall be provided at the request of
<br />the enforcing agency. Documentation may include, but is not limited to, the following:
<br />1. Manufacturer's product specification
<br />2. Field verification of on-site product containers
<br />5.504.4.4 Carpet Systems.
<br />All carpet installed in the building interior shall meet the requirements of the California Department of Public
<br />Health, "Standard Method for the Testing and Evaluation of Volatile Organic Chemical Emissions from Indoor
<br />Sources Using Environmental Chambers." Version 1.2, January 2017 (Emission testing method for California
<br />Specifications 01350).
<br />See California Department of Public Health's website for certification programs and testing labs.
<br />https://www.cdph.ca.gov/Programs/CCDPHP/DEODC/EHLB/IAQ/Pages/VOC.aspx#material
<br />5.504.4.4.1 Carpet cushion. All carpet cushion installed in the building interior shall meet the
<br />requirements of the California Department of Public Health,"Standard Method for the Testing and
<br />Evaluation of Volatile Organic Chemical Emissions from Indoor Sources Using Environmental
<br />Chambers,"Version 1.2, January 2017 (Emission testing method for California Specifications
<br />01350).
<br />See California Department of Public Health's website for certification programs and testing labs.
<br />https://www.cdph.ca.gov/Programs/CCDPHP/DEODC/EHLB/IAQ/Pages/VOC.aspx#material
<br />5.504.4.4.2 Carpet adhesive. All carpet adhesive shall meet the requirements of Table 5.504.4.1.
<br />DISCLAIMER:THIS DOCUMENT IS PROVIDED AND INTENDED TO BE USED AS A MEANS TO INDICATE AREAS OF COMPLIANCE WITH THE CALIFORNIA GREEN BUILDING STANDARDS (CALGREEN) CODE. DUE TO THE VARIABLES BETWEEN BUILDING DEPARTMENT JURISDICTIONS, THIS CHECKLIST IS TO BE USED ON AN INDIVIDUAL PROJ
<br />E
<br />C
<br />T
<br />
<br />B
<br />A
<br />S
<br />I
<br />S
<br />
<br />A
<br />N
<br />D
<br />
<br />M
<br />A
<br />Y
<br />
<br />B
<br />E
<br />
<br />M
<br />O
<br />D
<br />I
<br />F
<br />I
<br />E
<br />D
<br />
<br />B
<br />Y
<br />
<br />T
<br />H
<br />E
<br />
<br />E
<br />N
<br />D
<br />
<br />U
<br />S
<br />E
<br />R
<br />
<br />T
<br />O
<br />
<br />M
<br />E
<br />E
<br />T
<br />
<br />T
<br />H
<br />O
<br />S
<br />E
<br />
<br />I
<br />N
<br />D
<br />I
<br />V
<br />I
<br />D
<br />U
<br />A
<br />L
<br />
<br />N
<br />E
<br />E
<br />D
<br />S
<br />.
<br />
<br />
<br />T
<br />H
<br />E
<br />
<br />E
<br />N
<br />D
<br />
<br />U
<br />S
<br />E
<br />R
<br />
<br />A
<br />S
<br />S
<br />U
<br />M
<br />E
<br />S
<br />
<br />A
<br />L
<br />L
<br />
<br />R
<br />E
<br />S
<br />P
<br />O
<br />N
<br />S
<br />I
<br />B
<br />I
<br />L
<br />I
<br />T
<br />Y
<br />
<br />A
<br />S
<br />S
<br />O
<br />C
<br />I
<br />A
<br />T
<br />E
<br />D
<br />
<br />W
<br />I
<br />T
<br />H
<br />
<br />T
<br />H
<br />E
<br />
<br />U
<br />S
<br />E
<br />
<br />O
<br />F
<br />
<br />T
<br />H
<br />I
<br />S
<br />
<br />D
<br />O
<br />C
<br />U
<br />M
<br />E
<br />N
<br />T
<br />,
<br />
<br />I
<br />N
<br />C
<br />L
<br />U
<br />D
<br />I
<br />N
<br />G
<br />
<br />V
<br />E
<br />R
<br />I
<br />F
<br />I
<br />C
<br />A
<br />T
<br />I
<br />O
<br />N
<br />
<br />W
<br />I
<br />T
<br />H
<br />
<br />T
<br />H
<br />E
<br />
<br />F
<br />U
<br />L
<br />L
<br />
<br />C
<br />O
<br />D
<br />E
<br />.
<br />Y N/A Y N/A Y N/A Y N/A
<br />RESPON.
<br />PARTY
<br />RESPON.
<br />PARTY
<br />RESPON.
<br />PARTY
<br />RESPON.
<br />PARTY
<br />Y = YES
<br />N/A =NOT APPLICABLE
<br />RESPON. PARTY =RESPONSIBLE PARTY (ie: ARCHITECT, ENGINEER,
<br />OWNER, CONTRACTOR, INSPECTOR ETC.)
<br />TABLE 5.504.4.3 - VOC CONTENT LIMITS FOR ARCHITECTURAL
<br />COATINGS2,3
<br />GRAMS OF VOC PER LITER OF COATING, LESS WATER & LESS EXEMPT COMPOUNDS
<br />COATING CATEGORY CURRENT VOC LIMIT
<br />FLAT COATINGS 50
<br />NONFLAT COATINGS 100
<br />NONFLAT HIGH GLOSS COATINGS 150
<br />1"12"0
<br />PROPRIETARY AND CONFIDENTIAL
<br />ABCDEFGH
<br />1
<br />2
<br />3
<br />4
<br />5
<br />6
<br />DATENO.REVISIONORIGINAL SIZE 24"X36"
<br />SHEET SIZE ARCH "D"
<br />3500 DEER CREEK RD.
<br />PALO ALTO, CA 94304
<br />(650) 681-5000
<br />3/27/2024AARCH SITE PLAN COMMENTS10/18/2024BCIVIL AND BUILDING COMMENTS14700 THORNTON RDLODI, CA 95242, USCALGREEN
<br />CHECKLIST
<br />G-006
<br />REV: B IFP
<br />MVANDERWALPLOT DATE: 10/25/2024 9:21 a. m.
<br />JB-9528024TESLA SUPERCHARGER_LODI, CAPHASE 1: 16 SUPERCHARGERSB
|