INSTALL_1995 - Laserfiche WebLink

Home Browse Search

ote Preparation and Installation Iouctions : EMC Basic Monitoring Console lbarco 5. Place the second adaptor on top of the probe canister with its bevelled edge up and its locking tabs aligned with the flats an the canister. i. 6. Press the adaptor onto the canister until the locking ,w`L Qin, WGNEr tabs are on the flats.Twist the adaptor until its locking - W"A° tabs snap into the locking grooves. a7 D.FLOAT ASSEMBLIES 11 1. Remove the fuel float and water float from the Magne- tostrictive Probe Installation Kit box(refer to Figure 15 FUEL FLOAT or 16). I ASSEmaLY W(',NLT 2. Ballast rings are factory-installed on the water float of WATER FLOAT YN TOP ASSL NtlLr magnetostrictive probes to ensure proper float action. The ring type varies with the fluid being measured.Float Figure 20. Probe Assembly for Products Requiring ballast rings are available for the following liquids: Water Measurement(2" Installation Kit) Ballast Ring G2 — used with: aviation gas, regular unleaded gasoline,premium unleaded gasoline,leaded NOTE: When using 2" floats, be sure to choose 2" gasoline,gasohol �„ float during In-Tank Setup. Ballast Ring L2—used with: motor oil, toluene, xylene, CAUTION: INSTALL THE FLOATS MAGNET- gear oil 90W,transmission fluid. SIDE UP. IF THEY ARE INSTALLED INCOR- Ballast Ring D2—used with:jet fuel,kerosene,diesel RECTLY,INCORRECT FUEL HEIGHT AND WA- TER HEIGHT READINGS WILL RESULT. The following liquids do not use a water float,as water is CAUTION:WHEN SLIDING THE FLOAT ONTO not measurable in the liquid:ethylene glycol(antifreeze), THE PROBE SI�IAFT, BE CAREFUL NOT TO FIN- propylene glycol (antifreeze), wastewater, windshield BREAKANY OFTHE MAGNET RETENTION FIN- GERS. THIS COULD RESULT IN IMPROPER washer fluid, used oil, fuel oil #4 with specific gravity MOVEMENTOFTHE FLOATAND INACCURATE greater than 0.925. READINGS. NOTE:Only the water float mounting tube will be w used in place of the water float assembly for the = products where water measurement is not possible. (See Figure 21). ;t 3. Gently slide the fuel float onto the probe shaft, magnet-side up. The float should move freely on the probe shaft.(See Figure 19 or 20,"Probe Assembly for MAGNET Ml TOP MAGNET Products Requiring Water Measurement," or Figure w Tom. 21,"Probe Assembly for Products h=Requiring Wa- aoaT ter Measurement"). 'y +' f<' ll ni 1c��, Ik FUEL FLOAT WATER FLOAT MAGNET f BALLAST 03W ASSEM9LY MOUNUNG TUDE 1T OP RLUUmEOJ 1, Figure 21. Probe Assembly for Products N41 Requiring Water Measurement(4"Installation Kit) 4. Gently slide the water float mounting tube onto the MAGNET -endprobe shaft, magnet end first, ballast last. The FUEL FLOAT W TOP WATER FLOAT ASSEWALr ASSEMULr float should move freely an the probe shaft. (Refer to Figure 19 or 20,or 21.) Figure 19. Probe Assembly for Products Requiring CAUTION:WHEN SLIDING THE FLOAT ONTO Water Measurement(4"Installation Kit) THE PROBE SHAFT, BE CAREFUL NOT TO BREAKANY OFTHE MAGNET RETENTION FIN- NOTE:The fuel float must be placed magnet-side ,GFRs. THIS COULD RESULT IN IMPROPER inin toeffectivelymeasure fuel.The magnet islocated MO,VEMENTOFTHE'FLOATANDINACCURATE the narrow cylindrical end of the fuel float. The READINGS. wider end of the float is marked "BOTTOM THIS SIDE DOWN". 5. Slide the boot onto the end of the probe,and turn until BE SURE TO SLIDE THE MAGNET END OF THE t gyre's or es or 21.intothe probe detents.(Refer to FLOAT ON FIRST. 15