COMPLIANCE INFO_PRE 2019 - Laserfiche WebLink

Home Browse Search

• • IPS MATERIAL SAFETY DATA SHEET Date Revised MAR 2005 WELD-ON Supersedes:MAY 2004 Information on this form is furnished solely for the purpose of compliance with the Occupational Safety and Health Act and shall not be used for any other purpose. IPS Corporation urges the customers receiving this Material Safety Data Sheet to study it carefully to become aware of the hazards,if any,of the product involved. In the interest of safety,you should notify our employees,scents and contractors of the information on this sheet. SECTION I MANUFACTURER'S NAME Transportation Emergencies: IPS Corporation CHEMTREC:(800)424-9300 ADDRESS Medical Emergencies: 17109 S.Main St.,P.O.Box 379,Gardena,CA.90248 3 E COMPANY (24 Hour No.) (800)451-8346 Business:(310)898J300 CHEMICAL NAME and FAMILY TRADE NAME: Acrylic cement WELD-ON 16 for Acrylic Mixture of Acrylic Resin and Organic Solvents FORMULA:Proprietary SECTION II - HAZARDOUS INGREDIENTS One of the ingredients listed below is listed as a carcinogen(];)by IARC and NTP CAS# APPROX%ACGIH-TLV ACGIHSTEL OSHA-PEL OSHA-STEL Synthetic Acrylic Resin NON/HAZ 5-20 N/A N/A Methylene Chloride ($) 75-09.2 30-60' 50 PPM 25 PPM 125 PPM Methyl Acetate 79-20-9 0-35' 200 PPM 250 PPM 20D PPM Methyl Ethyl Ketone 78-93-3 0-40' 200 PPM 300 PPM 200 PPM 300 PPM Methyl Methacrylate Monomer 80-62-6 0-5 100 PPM 100 PPM All of the constituents of Weld-On adhesive products are listed on the TSCA inventory of chemical substances maintained by the US EPA,or are exempt from that list 'Title III Section 313 Supplier Notification: This product contains toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning and Community Right-To-Know Act of 1986 and of 40CFR372. This information must be included in all MSDS's that are copied and distributed for this material. PROPOSITION 65 NOTICE This product contains chemicals known to the state of California to cause cancer. This material is an aspiration hazard and defats the skin.The ingredients are toxic by inhalation and ingestion and may be absorbed through the skin.Exposure by these routes may cause central nervous system depression,liver and kidney damage and may sensitize the heart muscle.Methylene Chloride may interfere with the oxygen carrying capacity of the blood.Methylene Chloride is a possible human cancer hazard based on test results with laboratory animals.Methylene Chloride has been listed as a potential carcinogen by IARC and NTP. Methylene Chloride is not believed to pose a measureable risk to man when handled as recommended. Under some circumstances,mutagenic changes have been observed with Methyl Methacrylate in animal studies.Precautions should be taken to avoid unnecessary exposure to this cement. SHIPPING INFORMATION SPECIAL HAZARD DESIGNATIONS DOT Shipping Name: Flammable liquid,toxic,n.o.s.(Methyl acetate, HMIS NFPA HAZARD RATING DOT Hazard Class: 3;Subsidiary Risk: 6.1 Dichloromethane) HEALTH: 3 2 0-MINIMAL Identification Number: UN 1992 FLAMMABILITY: 3 3 1-SLIGHT Packaging Group: II REACTIVITY: 0 0 2-MODERATE Label Required: Flammable Liquid&Toxic(Domestic&International) PROTECTIVE 3-SERIOUS EQUIPMENT: B-H 4-SEVERE B=Eye,Hand/Skin Protection(Normal use or application&small spill Exceptions: None clean-up activities) H=Eye,Hand/Skin and Respiratory Protection plus Impermeable Apron When risk of immersion dipping and/or splashing is resent SECTION III - PHYSICAL DATA APPEARANCE ODOR BOILING POINT('F/'C) Clear,thin liquid Ketone like odor 104-F(40°C)Based on first boiling component: Methylene Chloride SPECIFIC GRAVITY 73-F Y 3.8'(23-C 12') VAPOR PRESSURE(mm Hg.) PERCENT VOLATILE BY VOLUME(%) Typical 1.10:0.040 355 mm Hg.®68-F(20'C)based on first boiling Approx.80-95% component,Methylene Chloride VAPOR DENSITY(Air=1) EVAPORATION RATE(BUAC=1) SOLUBILITY IN WATER 2.93 based on Methylene Chloride Approx.14.5 based on Methylene Chloride Solvent slightly miscible Resin precipitates VOC STATEMENT:Maximum VOC emissions as applied and tested per SCAQMD Rule 1168,Test Method 316A:350 Grana rt ter(gn).Meets VOC emission limits far Plastic Cement Welding. SECTION IV - FIRE AND EXPLOSION HAZARD DATA FLASH POINT FLAMMABLE LIMITS LEL UEL 21°F -6°C T.C.C.based on MEK Percent b Volume 1.8 11.5 FIRE EXTINGUISHING MEDIA Dry chemical,carbon dioxide or foam.Water may be an ineffective extinguishing agent. SPECIAL FIRE FIGHTING PROCEDURES The use of a SCBA is recommended for fire fighters.Water spray may be useful in minimizing vapors and cooling containers exposed to heat and flame.Avoid spreading burning liquid with water used for cooling purposes. UNUSUAL FIRE AND EXPLOSION HAZARDS Avoid hot surfaces and other sources of ignition. a: mar-04