Laserfiche WebLink
DISPENSER <br /> STABILIZING BAR j <br /> SUMP SENSOR J-BOX SPRING NUT 2-IN-1 SENSOR BOX <br /> DISPENSER SUMP r . <br /> FRAME 1 <br /> PRODUCT SHEAR <br /> ANCHOR BOLT VALVE a r c h i t e c t u r e <br /> ELBY CAPPED ELBOW MOUNTING FLANGES e n g i n e e r i n g <br /> (TYP.) DISPENSER JUNCTION ANCHOR BOLTS <br /> BOX (TYP.) 6"THICK RIVE SLAB MINI HYDROSTATIC SUMP L} IB & �ssoda+es, Ltc�. <br /> ANNULAR SENSOR W/BRINE <br /> RESERVOIR WITH SIGHT GLASS (TYP.) 867 Pacific Street,Suite 120 <br /> o San Luis Obispo,CA 93401 <br /> ph 805.540.5240 <br /> DISPENSER SUMP FRAME SEAL-OFF (TYP.) ° 4 a ° CONDUITS ROUTED fax 805.540.5241 <br /> THROUGH SLOTS IN www.LHBassoc.conn <br /> SUMP FRAME (TYP) <br /> RUN CONDUITS THROUGH DISPENSER UNDER DISPENSER 1-1/2"MxMS FLEX CONNECTOR <br /> HOLES IN DISPENSER SUMP "BRAVO" (TYP.) <br /> FRAME"A"SIDE OR"B" DOUBLE WALL FRP 30"DEEP QE-FESS/O <br /> SIDE O.K. (TYP.) <br /> CONTAINMENT SUMPBFq� <br /> SENSOR MOUNTING w <br /> DISPENSER KIT e No.78916 <br /> 6 m <br /> * . rn <br /> MONITORING CONDUIT SENSOR MOUNTING 0j 8 <br /> HANGER KIT (TYP.) LIQUID SENSOR00 <br /> q7 VI <br /> DISPENSER POWER <br /> 3"OVER 2" D.W. P OF CA�FO <br /> & DATA CONDUIT SUMP MONITOR FRP PRODUCT PIPING <br /> LIQUID SENSOR I <br /> 1-1/2"90° ELBOW (TYP.) 3 CONSULTANTS <br /> 1-1/2"x2" BELLxFEMALE FRP ADAPTER (TYP.) <br /> NOV FIBERGLASS D.W. CUFF <br /> 2"FRP TERMINATION FITTING WITH TEST ENTRY <br /> PORT AND VACUUM TUBING ROUTED TO <br /> VACSENSORASSEMBLY (TYP.) <br /> J CONDUIT ROUTING DETAIL (�4VPRODUCT PIPING AT DISPENSER <br /> SCALE: N.T.S. ' SECTION <br /> SCALE: IN TS. <br /> DISPENSER VAPOR PRESSURE SENSOR (1 PER SITE) <br /> STABILIZING BAR <br /> SPRING NUT <br /> VAPOR FLOW SENSOR 1 PER DISPENSE REVISIONS <br /> DISPENSER SUMP ( PLAN CHECK#16-3684 <br /> FRAME <br /> 07 DECEMBER 2016 <br /> 1"STREET 90°WITH 1" NPT NIPPLE ENGINEERING PLAN CHECK <br /> ANCHOR BOLT (SUPPLIED BY CONTRACTOR) #16-3684,3685 29 MARCH 2016 <br /> MOUNTING FLANGES VAPOR SHEAR SJC EHD PLAN CHECK <br /> VALVE #SR0076222 8 NOVEMBER 2017 <br /> 3 6"THICK RIVE SLAB <br /> AA AA ANCHOR BOLTS <br /> a 0 <br /> SUBMITTAL DATES <br /> OWNER: <br /> UNDER DISPENSER 1-1/2"MxMS FLEX CONNECTOR (TYP.) 03/29/2016 <br /> "BRAVO" REG. AGENCIES <br /> DOUBLE WALL FRP 30"DEEP <br /> FLANGE W/1"NPT CONTAINMENT SUMP -- <br /> 1/2"x 1"THREADED . THREADED INLET O.T.B.: <br /> MALE ADAPTOR INLET SCREEN <br /> VAPOR FLOW PROJECT NO. <br /> SENSOR CABLE TO JUNCTION 15-13-001 <br /> BOX � <br /> 1"SHORT NIPPLE 3"OVER 2" D.W. DRAWN BY: <br /> FRP VAPOR PIPING AFS <br /> "' .------- OUTLET O-RING <br /> 1"90°STREET CHECKED BY: <br /> ELBOW A FLANGE W/1"NPT JRB <br /> STABILIZER ASSEMBLY THREADED OUTLET 1-1/2"90° ELBOW (OR TEE WHEN <br /> TOP OF ISLAND 1"PLUG CONNECTING TO ISD PRESSURE SENSOR) <br /> 1-1/2"x2"BELLxFEMALE FRP ADAPTER NOV FIBERGLASS D.W. CUFF <br /> ENTRY <br /> 2"FRP TERMINATION FITTING WITH TEST <br /> VAPOR SHEAR VALVE PORT AND VACUUM TUBING ROUTED TO NOTE: <br /> NOTES VAC SENSOR ASSEMBLY CONDUIT AND SENSORS NOT <br /> 1. (1)VAPOR FLOW SENSOR REQUIRED PER DISPENSER.SENSOR SHALL BE SHOWN IN THIS DETAIL FOR <br /> MOUNTED ABOVE SHEAR VALVE. CLARITY. 59 <br /> co <br /> W m <br /> 4 ISD VAPOR FLOW SENSOR 2 VAPOR PIPING AT DISPENSER U U) Z <br /> SCALE'NTS SECTIO N <br /> SCALE: N.T.S. W Z0 <br /> L Q <br /> J <br /> ' Z <br /> Q � 0 <br /> 4� ° <br /> ow <br /> tZ <br /> � Q <br /> VAPOR PRESSURE SENSOR <br /> CABLE TO JUNCTION <br /> MOUNT SENSOR TO DISPENSERS BOX <br /> INNER FRAME WITH SUPPLIED <br /> BRACKET <br /> PRESSURE SENSING <br /> PORT 1/4"OD COPPER TUBING. <br /> AVOID ANY TRAPS!(BY <br /> CONTRACTOR) a SHEET TITLE <br /> 1/4"TUBE W/1/4"NPT MALE <br /> ADAPTER FITTING INTO TEE <br /> FITTING.#CA68A-4 <br /> r <br /> CAP REDUCE THREADS FROM 1-1/2" PIPING INSTALL <br /> TO 1/4"WITH DOUBLE TAP <br /> p PIPEBUSDOPE <br /> APPLY APPROVED DETAILS AT <br /> 2-WAY CALIBRATION PIPE DOPE AT ALL THREADS FOR v <br /> VALVE A TIGHT SEAL. <br /> PRODUCT <br /> 15 <br /> DISPENSERS <br /> VAPOR RETURN <br /> 0 <br /> BACK TO TANK 0 <br /> 0 <br /> U <br /> NOTES <br /> M <br /> 1. ONLY(1)VAPOR PRESSURE SENSING DEVICE REQUIRED PER SITE_ <br /> SENSOR SHALL BE MOUNTED AT ONLY DISPENSER LOCATED CLOSEST t <br /> TO TANKS. v <br /> B SHEET NO. <br /> NTRACTOR SHALL PITCH ALL 1/4"TUBING AS REQUIRED TO AVOID Y <br /> ANY LIQUID TRAPS <br /> m <br /> 0 <br /> (�) VEEDER-ROOT ISD VAPOR PRESSURE <br /> FS <br /> `' SENSOR CONNECTION SCALE NTS M <br />