COMPLIANCE INFO_2016 - 2018 - Laserfiche WebLink

Home Browse Search

UL/ULC Listed Red Threadgll A Piping System GENERAL SPECIFICATIONS Primary Piping SECTION 1 - Qggpe This section covers the use of fiberglass reinforced plastic 2.06 Acceptable Manufacturers - NOV Fiber Glass (FRP) pipe for single wall fuel handling and fuel handling vent Systems, 501-568-4010,or approved equal. and vapor applications Including gasoline, unleaded gasoline, gasoline/alcohol mixtures, bio-diesel and diesel up to 150°F Section 3 - Material and Construction and 250 psig cyclic pressure. 3.01 2"-4" Pipe - The pipe shall be manufactured by the filament winding process using an amine cured epoxy SECTION 2 - General Conditions thermosetting resin to impregnate strands of continuous 2.01 Material furnished and work glass filaments, which are wound around a mandrel at a performed under this section shall be coordinated with the 543/4° winding angle under controlled tension. The pipe related work and equipment specified under other sections, shall be heat cured and the cure shall be confirmed using a i.e.Valves, Flexible Connectors, Equipment. Differential Scanning Calorimeter. Pipe shall be supplied with a T.A.B.- (Threaded and 2.02 Governing Standards - Except as modified or Bonded)ends. supplemented herein, all materials and construction methods Pipe shall have a minimum continuous cyclic pressure shall comply with and be tested in accordance with the rating of 125 psig at 150°F in accordance with ASTM L12992, following standards and test methods: Procedure A or UL 971 pressure rating. Standards and Test Methods: All pipe shall be 1009& hydrotested at the factory before UL971 Standard for Nonmetallic Underground Piping for Flam- shipment at a minimum pressure of 265 psig and shall be 2004 mable Liquids UL971-2004 Listed and labeled. ASTM Standard Classification for Machine-Made"Fiberglass" 3.02 ASTM D2310 Classifications fat 73.41F1 D2310 (Glass Fiber Reinforced Thermosetting Resin)Pipe 2--3- RTRP-IIAF ASTM Standard practice for obtaining Hydrostatic or Pressure q" RTRP-I 1 AH D2992 Design Basis for"Fiberglass" (Glass Fiber Reinforced (Mechanical properties cell classifications shown are Thermosetting Resin)Pipe and Fittings minimums.) 3.03 F€ttl1)gs - All fittings shall be manufactured using 2.03 Operatinci Conditions - In addition to the above the same type of material as the pipe. Fittings may be listed minimum design requirements, the system shall meet manufactured either by compression molding, filament the following minimum operating conditions: winding, resin transfer molding or contact molding methods. a. Operating Pressure All fittings, adapter, and sump penetrations shall be UL971- 2004 Listed. b. Fluid Conveyed Fittings shall be adhesive bonded matched tapered bell c. Test Pressure and spigot. 3.04 Connections - Connections to flex connectors or 2.04 Quality Assurance - Pipe manufacturer's quality other piping materials shall be made by the use of NPT program shall be In compliance with ISO 9001 and/or API O1. (National Pipe Thread) threaded adapters or flanges bonded to the FRP piping system. 2.05 Delivery. Storage. and Handling - Pipe and fittings 3.05 Sump Penetrations - Sump penetrations shall be shall be protected from damage due to impact and point made by means of a permanently bonded FRP coupling. The loading. Pipe shall be properly supported to avoid damage coupling shall be capable of adjusting for the slope of the due to flexural strain. The contractor shall not allow dirt, piping system entering or exiting the sump wall. debris or other extraneous materials to get into pipe and 3.06 Adhesives - Adhesives shall be manufacturer's fittings. All factory machined areas shall be protected from standard for the piping system specified. sunlight until installed. VOWWAgapipe.com 2700 West 65th Street 25 S.Main Street 171''' Fiber Glass Systems Little flack,Arkansas 72209 Sand Springs,Oklahoma 74063 Phane:1 (501)568-4010 1(918)245-6651