|
t
<br /> a
<br /> Step 79: Electronic Liquid Level Monitoring H14790PA
<br /> If an electronic level monitor is installed, it must be calibrated to match the top of the 61 SO valve body, which i July 2003
<br /> must correlate with 95% of the actual tank capacity. i
<br /> PREVENTATIVE MAINTENANCE
<br /> �. .
<br /> Annually, inspect the flapper in the 61 SO to see that it is open by looking down the drop tube opening. Test the
<br /> 61 SO drop tube seals with CARB procedure TP-201.1 D. If the drop tube seal passes testing, no further
<br /> maintenance is required. If the drop tube fails testing, replace the drop tube seal with OPW PIN: H11931 M for 4"
<br /> Tubes. Re-test the 61SO drop tube with CARIB procedure TP-201.1 D. If this does not correct the leak the 61SO
<br /> needs to be replaced.
<br /> CAUTION: Do not insert any foreign object into drop tube if flapper is in the closed position. For example
<br /> a tank level measuring stick. This will damage the valve and void the Warranty. ALWAYS check flapper OPW Installation & Maintenance
<br /> location before "sticking" the tank. If flapper is in the closed position the tank is either over filled and you
<br /> need to wait until the liquid level goes down or the 61SO is damaged and needs to be replaced.
<br /> Instructions
<br /> 6150 Performance Specifications: �
<br /> This Overfill Prevention Valve has been manufactured and tested to, and met, the following California
<br /> specifications. Performance Requirement: teak rate to be less than or equal to 0.17 @ 2A"W.C.
<br /> Torque Specification:
<br /> ASSEMBLY, INSTALLATION, and MAINTENANCE
<br /> Self-Clinching Studs, 5116-8 UN thread, 11.5 ft-lbs minimum to 13.5 ft-lbs maximum. INSTRUCTIONS FOR OPW 61 SO-EVR VAPOR
<br /> i
<br /> Important: Leave these installation instructions and maintenance procedures with the station TIGHT, OVERFILL PREVENTION VALVES.
<br /> operator,
<br /> Notice: OPW products must be used in compliance with applicable federal,state,and local laws and regulations. Product
<br /> selection should be based on physical specifications and limitations and compatibility with the environment and material to be IMPORTANT: Please read these assembly and
<br /> handled. All illustrations and specifications in this literature are based on the latest production information available at the time installation instructions completely and carefully before
<br /> of publication. Prices,materials, and specification are subject to change at any time,and models may be discontinued at any
<br /> time, in either case,without notice or obligation. Starting. 1
<br /> Standard Product Warranty
<br /> f
<br /> OPW warrants that products sold by it are free from defects in materials and workmanship for a period of one year from the f ,
<br /> date of manufacture by OPW(ECO products two years from date of manufacture.) Proof of purchase may be required. As the 1 j
<br /> exclusive remedy under this limited warranty, OPW,will at its sole discretion, repair, replace,or issue credit for future orders
<br /> for any product that may prove defective within the one year date of manufacture period (repairs, replacements,or credits may
<br /> be subject to prorated warranty for remainder of the original warranty period,complete proper warranty claim documentation r
<br /> required.) This warranty shall not apply to any product that has been altered in any way,which has been repaired by any party i
<br /> other than a service representative authorized by OPW,or when failure is due to misuse,or improper installation or
<br /> maintenance. OPW shall have no liability whatsoever for special, incidental or consequential damages to any party,and shall
<br /> have no liability for the cost of labor,freight,excavation,clean up,downtime, removal, reinstallation,loss of profit,or any other �r
<br /> cost or charges.
<br /> For any product certified to California 2001 standards, OPW warrants that product sold by it are free from defects in
<br /> material and workmanship for a period of one year from date of manufacture or one year from date of registration of
<br /> installation not to exceed 15 months from date of manufacture by OPW.
<br /> THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,AND SPECIFICALLY THE Vapor Overf Il
<br /> WARRANTIES OF MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE. THERE ARE NO WARRANTIES,WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
<br /> 1=1 VV. Prevention Valves
<br /> AIDOYFR eOMPAerr
<br /> P.O. Box 405003* Cincinnati, Ohio 45240-5002
<br /> 1-800-422-2525 Domestically
<br /> 513-870-3315 Internationally i
<br /> www.opw-fc.com
<br /> Copyright, 2003 -OPW Fueling Components Inc., Cincinnati, OH
<br /> Printed in U.S.A. pin H14790PA-7103
<br /> i
<br /> OPW 61 SO Overfill Prevention Valve Page 8 OPW 61 SO Overfill Prevention Valve Page 1
<br /> i
<br />
|