Laserfiche WebLink
Figure 2A Figure 213 <br /> Typical Product Side Installation of Phil-Tile System Using 61SO-PT Typical Product Side Installation of Phil-Tice System Using EBW Autolimiter 11 708-49X-Series <br /> Duet Cap Phil-Tile Cast Iron Dust Cap _Phil-Tite Cost Iron <br /> Finish Grade Lid wim Mton Seal Finish Glade Lid with Viton Seal <br /> Spill container must be Phll-Tlte Fit Spill container must be Phil-TNM FIB <br /> metalled 1.25 Below SwNel Adeplr Installed 1 26 BWW gdyst Adaptor <br /> Fli Grade Flnleh Grade <br /> AYI $RI <br /> iN'Fht Sest Ph9-Tits Mil 1 Sense phl-Tits,8111 1 sense <br /> PM 85039 Spill Comalner m» de <br /> vead 1/P Flat Sul Spill Container is threaded <br /> directly on Me Riser Adaptor PM 85039 directly on the R bor Adaptor <br /> or Tank Riser. or Tank Riser. <br /> For GARB EVR Instal lotions, -Drain Path For CARB EVR Installations, <br /> ath <br /> install ttw drop tube below .....Drain Valve install the drop tube below Drain aim <br /> the Il con�inerdralnvalve. Drain Valve <br /> 1/4'Flat Seal P/N 85039 the spill container drain valva. <br /> --1I4'Flet Seal P/N 85039 <br /> Drop Tube Seal Tube Flared Flange _. Drop Tube Flared Flange <br /> PM 85039-DT Drop Tube Seal <br /> Poser Atleptor(WF 4X4) PM 85039-07 _ Riser Adaptor(WF 4X4) <br /> 4"Threaded Tank Riser - 4"Threaded Tank Riser <br /> Top of Storage Tank <br /> —nlyrAstlalaasalBWrndar rruat-- Top of Storage Tank <br /> z_ <br /> Upper Section of Drop Tube and <br /> Upper Section d Drop Tube and <br /> Shut-off Valva is factory assembled <br /> 61S0EPT Shut-OI(Flost i and tested to meet a maximum leak Autolimilr body is factory awambla0 <br /> rete of 0.17 CFH at 2.00"of WC and tested to meet a maximum leak <br /> rate o10,17 CFH at 2.00"of WC <br /> i <br /> EBW Aulolimder Shut-ort Verve <br /> Bottom section of drop W be is <br /> �._ threaded and screws on to Note: Bottom section of drop tube is <br /> Note. Shut-OtF valve The discharge opening of be fill-pipe threaded and screws on W <br /> The discharge opening of the fill-pipe 13'Mnmum most be entirely submerged wren Ne Autoiimiter valve <br /> mull ba entirely submerged vhen Ne Clearance Mliquid level is six inches above the <br /> liquid level is six incrive above Ne FbBt Tt1s Orrd D(the Bottom 6eW m Of ll>a bosom of the tank. c e TTe end D(the Bottom Section O(the <br /> bottom of vie tank. drop lube should be but streight or on <br /> and angle drop tube should be cut straight or on <br /> _________________ . .._____ __ _________ 9 _ and angle <br /> ______________________r __ __ _____________________ <br /> IN ssbea'orlum Bottom of Storage <br /> j DWt iobowwt l BodomdStxege Tank <br /> — L _ <br /> Executive Order VR-101-L,FFS Phil-Tile Phase I Vapor Recovery System,Exhibit 2, Page 6 Executive Order VR-101-L,FFS Phil-Tice Phase I Vapor Recovery System,Exhibit 2, Page 7 <br />