COMPLIANCE INFO_2009 - 2015 - Laserfiche WebLink

Home Browse Search

May 18 2009 14: 38 Armour Petroleum Service 707-437-6068 p. 3 RED THREAD011 Piping System ar i i� iris GENERAL SPECIFICATIONS SECTION fl - Scope 2.03 Q22Eaena opnditlone- In addition to the above This section covers the use of fiberglass reintorced plastic listed m nlmunl design requirements, the system shall (FRPi pipe for mild chemical arid water awvicea up to 21 o'F meet the following minlmwm operating conditions: and 450 pelg steady pressure. a.Operating Pressure The piping System shall be furnished and Installed oOmplete b,Operating Temperature with all fittings,lolning materials, Supports, specials, and other c. Fluid Conveyed necessary appurtenances. d.Tear Pressures 6aCTClN 4 _ aan�raf Condltione 2,04 Quellty Aaeuranoe - Pipe manufneturef'9 qual- 2.01 j-1nptdlipaalalflp - Material furnished end work per- Ity program shall be In compliance with ISO 8001 and/ fomled under this section shall be coordlnsted with slated or API Qi. wort:and aqulpmetlt spacltied under other sections. Valves Section 2,05 Deltvefv. Stomas. and Handling - Plpe and fit- Supports Section tinges shall be protected from damage due to Impact and Equipment Section point loading. Pipe shall be pmpery supported to avoid dam- age due to flexural avakta, The contractor shall not allow dirt, 2,02 Oovemltw Standards -Except as modified or sup- debris, or other extraneous materials to get Into pipe and plernented herein, all materials and construction methods fittings. All factory machined areas shall be protected from shall comply with the applicable provielona of the following eurlllg)1l until Installed_ specifications and be tested using the following standards: 2.06 Acceptable Manufacturers - NOV Faber Glass Standard Sveoiflcations Systems, 501-558-4010, or approved equal. ASTM Standard pec a Olt or ameh our "Fiberglass" (Glass-Fiber-Rein(orced Ther- sZGT10N a - Matanaie enril Conpyuottan D2996 mosett" Resin) Pipe 3.01 2'-2a' Plow - The pipe shall be manufactured by ASTM Standard Specification for Reinforced the filament winding process using an amine cured epoxy 4024 Thermosetting Realn (RTO) Flarlgoe therrnoeetting reeln to Impregnate strands of continuous glass ASTMa ar pec ca on or "Fiberglass"' filaments,which are wound around a mandrel at a 54to/e wind- D5685 (Glass-Fl ber-Reinforced-Ther mosettl ng- Ing angle under controlled tension. Pipe shall be neat cured Resin) Pressure Pipe Fittings and the cure shall be confirmed using a Differential Soanning Calorimeter, Standard Test Mg;ltOds Standard ract ce for Maining HyTostatic Pipe shall be supplied with a matching tapered bell and a ASTM or Pressure Design Bas19 for "Fibarglass" matclNng taperad spigot. 02992 (Gla as-Ftbar-Relnforced-Thorrllosetting Resin) Pipe arid Fittings Pipe shall have a minimum continuous steady pressures rat- ASTM Standard Practice for Measuring Beam Ing of 225 pslg at 210°F In accordance with ASTM 02992 02925 Deflection of Reinforced Thermosetting procedure A. Plastic Pipe Under Full Bore Flow ASTM Standard Test Method for Sirort-Time Hy- All pipe ahall be 100%hydrotested at the factory before ship- 01599 drauilo Failure Pressure of Plastic Pipe. Tub- ment at a minimum pressure of 300 palg. Ing and Fittings standard Bs e o nr� n 3.02 F a pain and FAUnaa -All fittings shall be manu- ASTM elle Properties of "Flberglass" (Glass-Flber- lectured using the same type materials as the pipe. Fittings D2106 Relnforced-Thermosetting Realn) Pipe and may be manufactured either by co mpreseion molding, spray- 7Ube up/contact molding,or filament winding methods. ASTM Standard Test Method for Delos minatlon of 02412 External Loeding Characteristics of Plastic Pipe by Parallel-Plate Loading e ar.e"9y.S1,191 fR 1W AdWGlass stems 2700 Wasr 651h S1,191 zs�.Mnln Street Lillie Rock,Arta w 72205 Saul Springs,OkJOcor 7416:3 Phvw 1(50t 565-4010 1(018)245-FMI