COMPLIANCE INFO_2009 - 2015 - Laserfiche WebLink

Home Browse Search

Mag 18 2009 14: 38 Armour Petroleum Service 707-437-6068 p. 4 • RED THREAD* it Piping System Fittings shall be adhesive bonded matched tapered bell and 4.08 EMPALlinatnUallm- Pipe shall be Installed a6 specl- spigot, threaded or grooved adapters, or hanged. Fittings fled and Indicated on the drawings. shall be certified to ASTM MOM. The piping system shall be Installed In accordance with the Flanges shall have ANSI 818.5 Class 160 bolt hole patterns, manufacturer's current published Installation procedures. 3.03 AdhselVO - Adhesive shall be manufacturer's sten- 4.03 Tasting - A hydrostatic pressure toot shall be con- dard for the piping system specllled. ducted on the completed piping System. The piping system shall be subjected to 10 preasuri2:atlon cycles Tlom 0 pslg to 3.04 Daaksts- Gaskets shall be//e" thick, 50-70 durom- l,.times the design operating pressure as stated in section eter full-faces type suitable for the service shown on the draw- 2.03.0. After the 10 cycles, the pressure Mall be held on the Inge and ee recommended In the manufacture#'a standard system for a minlrnum of 1 hoot and the line Inspected for Installation procedures. leaka. 3.Oe 6olh. Nuts. f Waetlera -ASTM A307,Grade 8, Test pressure shall not exceed 11/2 times the maximum rated hex heed bolts shall be supplied. SAE washers shall be sup- pressure of the lowest rated element in the system, piled on all nuts and bone. Unes that are subjected to severe temperature cycles shell 3.08 - RED THREAD II as rnanlQae- be tested at 11/2 times the cyclic pressure rating of the low- furred by NOV Aber Glass Systen s,or approvad equal. set rated component, even If the system shall operate at low pressure. RECTInN 4-installation and Tisr_tlna 4.01 Tralnlna and Certification - All joints Installed or The system shall be filed with water at the lowest point and conatr ucted In the field shall be assembled by employees of air bled off from the highest point. "terns shall be brought the contractor who have been trained by the pipe rnanufac- up to test pressure slowly to prevent water hammer orover- turer. The pipe manutacturer or their authorized represen- presauriZation, tativs shall train the contractor's employees In the proper Joining and assembly procedures required for the project, All pipe Joints shall be water tight. Alt Joints that Ere found to including hands-on participation by the contractor's employ- leak by abservatlon or during testing shall be repaired by[he ass. Each bonder shall fabricate one pipe-to-pipe and one contractor and retested. pips-to-fitting Joint that shall pass the ntlnimunn pressure toot for the applk:atlpn as atatacl in section 2.03.4 without leaking. Only bonders who have successfully completed the pressure 's0 901 test shall bond pipe and fittings. Certification by the manufacturer shall be In compliance with ASME 831.3, Section A328.2 for the type of joint being made. /IOV RIiQR awes etlrsMs Natnne Oawen vnw bas produces mb Wom"for ganwm mrommom will,errs Iis.nat Wita ded fur dit tqn pr rpavaa. Asroagh every ertwtfee bean made 1st maiMan Hie acwrar.T and tNiWWdy of N writems,raabna O&M Vaso a no wad'aawarte ralSW tpiltty tot fabs b try loss,damage a"retulting from Me we of ptamalM and data hemp purr is 3rq'w'ifarWy erpreaees a rases. AWeWR CMW MW46Ins W11110 dere vRM Ere most Wmd wrtkn rated at be web aft rated In 50 Nualti e. 2700 WrtMarS" `0'" NW FiberGlassSystems 2700 Wet r�M Sireel 25 v.Main Street Unit Roca,Adar=72209 SaW Springs,Oklahma 74M o Trade.wk d lATwr w atweuv CD PRone:1 1501)56"10 1(918)745-5651 o tdoe.r"TIOWL auveu vraco AIM Febntar/Teep