Laserfiche WebLink
uuiii,y0 lb: uo rAe 12uoti2ZdbLy i0 PLASP EWLIr. liML U1L 41008 <br /> BRAVO <br /> • ipw <br /> II ° BULKHEADINSTALLATION <br /> ................................................................................................................ .................. <br /> Please note: All surfaces should be as clean as possible prior to <br /> tightening any bullhead fittings into place. BRAVO SYSTEMS B-200 BULYHEAD FIT FNGS HOLE Saw SIZE <br /> 1. For field installation for vapor recovery, penetration openings Bulkhead Hole Saw Bulkhead Hole Saw <br /> must be cut to accommodate the correct Bravo bulkhead fit- Fig size Fitting size <br /> tings.On the bottom of the box,indicate where vapor recovery BH 1/2"NPT 7/8" 3° &1.1/2°DBF 2" <br /> lines should go, and make the penetrations to accommodate BH 3/4"NPT 11/16" 4"&1-1/2"DBF 2" <br /> them. (Hole perforation sizes are noted on the side of the B-200 BH I"NPT 1318" 04 MYE 1-3/4" <br /> box and on chart 5-A at right.) BH 1-1/2" 2" a5 MYE 2" <br /> • Available sues for Bravo vapor recovery fittings: 1/2",3/4", 1", Note:DBF(Double Bottom Fitting) B 27 SET 2.3/8" <br /> )-1/2". for Conminme_ne of vapor Unes <br /> 2. With the long end up, place one Flat washer and one gasket <br /> onto the fitting.The fixed nut will be on the outside of the box. S" <br /> (See 5-B) ..... <br /> 3. Insert the fitting through the exterior of the B-200 box. Place Locking Nut <br /> one gasket and one flat washer onto the fitting from the interior <br /> of the B-200.Thread the nut onto the unit.Apply UL approved Gasket nslde of Con ainmanl Box <br /> pipe sealant to all pipe thread connections. <br /> 4. Above and below the base of the B-200 box, connect the vapor <br /> recovery line to the bulkhead fittings and/or factory installed <br /> couplings.Hold the bulkhead fittings stationary while connect- <br /> ing the vapor lines. If the B-200 box has factory-installed fit- Gasket <br /> tings,simply attach the lines. Fitting Body <br /> s-B <br /> NOTE: Bulkhead vapor fittings can be used for electrical pene- <br /> trations. <br /> ................................................................................................................................... <br /> • The MYE fitting is used to provide a continuous conduit run to <br /> the electrical seal off. <br /> • Electrical conduit fittings are available in 1-1/4"ST(MYE No.4) Electrical <br /> for 3/4'; 1-1/2"ST (MYE No. 5)for V. Consult your Bravo dis- Seal Off <br /> tributor. <br /> • A threaded half nipple is used to prevent leakage from the B- Continuous <br /> 200(See s•C). Conduit Run <br /> 1. For field installation MYE electrical fittings, penetration open- <br /> ings must be cut to accommodate the correct Bravo bulkhead MYE Fitting <br /> fittings. On the bottom of the box indicate where fittings Half Nipple <br /> should go, and make the penetrations to accommodate them. <br /> (Ser 5-.4). <br /> (orae of Conuinmem Bm <br /> 2. Apply pipe sealant to a half nipple and thread it into the MYE <br /> fitting. — v— Gasket <br /> 3. Insert the MYE fitting from the inside of the B-200 box. Insert Washer _ <br /> the gasket(See 5-C)from the outside of the B-200,then install a Locking Nut <br /> Iflat washer and a locking nut to vette a seal. t Y <br /> •4. Pass the conduit ulrough either the MYE or factory-installed �i <br /> electrical fittings. <br /> r <br /> _ 5 <br /> JUN-17-1998 1608 12066229629 96% P.08 <br />