COMPLIANCE INFO 1998-2003 - Laserfiche WebLink

Home Browse Search

..� i, . �� i�. � r.v a.��..a�..a ..�i r�.•i: [.v�"r. •-•� r1!lr. V1L 6J UlU — BRAVO • 0i " MAINTENANCE I STRUCTIONS IMPORTANT! ................................................................................................................................... ROUTINE FILTER CHANGES CAUTION! ��FIoaI Pivot IMPORTANT.Turn off power to the dispenser If the containment box Hitch Pin prior a changing the filter. is not performing nor- � mallwhen the o erat- 1. Check the float chain tension for proper y P adjustment Made sure it is connected to the ing instructions are fol- shear valve and the float arm. Lead e lowed, contact a quali- 2. Next test the float system by gently raising Seal fied service person or Clevls » P the float tubing approximately 1/4" to 1/2' Pin Bravo's customer ser- with the valve in the open position. This 7-a vice at(800)282.7286. action should dose the shear valve.If it does Outside U.S.A., call not, refer to Adjusting the Float Mecha- the containment box. Use the manufacturer's nism. supplied cup/collector to minimize fuel loss. not attemptmpt tto (714) Do 5. Next remove all fluids from the containment o service 3. Examine the lead seal at the float chain or pivot (7-A)and if the seals were not altered, box. Bravo's manual siphon pump is or repair the contain- continue with the next step.If the seals were designed to connect to the top of the float ment box yourself. altered, refer to Step 7 of Adjusting the Float tubing for easy fluid removal. DO NOT leave Mechanism• absorbent materials in the containment box • Prior to any mainte• q. While removing the filter, collect as much to soak up fluids. Hance, assure that the fuel as possible from the filter before it enters 6. Properly dispose of removed fluids according to containment box ince local,state and federal regulatory guidelines. rior is clean and free of ................................................................................................. debris and obstruc- ADJUSTING THE FLOAT and thread it through the lead disc. Pull the tions, especially in the float area. MECHANISM wire taunt and crimp the disc to prevent tam- • Do not tamper with 1. Remove the hitchpins from the float drain pering.(7-A) or modify the float (see 7-B). If the lead seal on the float pivot was altered, re-secure it by looping the wire through the device or the shutoff 2. Reset the shear valve in the open position. clevis pin (7-A)and twisting the wire togeth- system. This includes (see 7-11). er.Thread the wire through the lead disc.Pull the lead seals and the 3. If a fluid test was performed, drain the float the wire taunt and crimp the disc. float chain. Any tam- reservoir through the float tubing by using Initial Installation:Continue with Step 5, Pae 6. pering with these the Bravo siphon pump. g components is iLLE- Routine Filter Change:Continue with Step 4 of GAL and transfers the 4. Properly dispose of removed fluids according Routine Filter Changes. liability for the shut- to regulatory guidelines. Off system function to 5. Reconnect the float chain to the valve trip the person or persons mechanism (7-A). Put the hitch pins back in who tamper with the place. Retest the float-trip mechanism while above components. adjusting the tension chain until there is no • Assure that the con- more slack. HITCH PINS tainment box is not 6. Retest the float trip mechanism. During the I A submersed in fuel, retest, if the float trips the valve correctly OPEN VALVE water or other fluids. then proceed with Step 7. NO"t'E: If the float • • The interior of the con- still does not function correctly, immediately tainment box must not call Bravo technical assistance at (800) 282- a'. ' CLOSE VALVE be directly exposed to 7286,Outside USA,call(714)739-9686. rock:salt,ice or snow. 7. Install the tamperproof lead seal to the float chain(as shown in 7-A).Twist the wire together _ 7 JUN-17-1998 16:09 12066229629 95% P.10