COMPLIANCE INFO 2017 - 2018 - Laserfiche WebLink

Home Browse Search

MSZ BLM-xx Page 2 Step 7: Install The Eccentric Insert&Multi-Sync Reducer • Dry fit the Eccentric insert.Make sure it fits properly over the pipe&inside the *' sleeve. • Dry fit the Multi-Sync Reducer a • Adjust the positions so that they lineup properly with the Repair Sleeve&Pipe. Note: A proper fit will not cause extra pressure or force to the sleeve and will allow a longer lasting repair. • Once you have the part lined up correctly 1. Pull back the Multi-Sync Reducer&Eccentric Insert 2.Apply Zip Tite bonder all around the Eccentric Insert, 3. Slide Eccentric into the Repair sleeve in the proper position 4. Apply Zip Tite bonder all around the Multi-Sync Reducer Adjust the position of the Eccentric Insert& Multi 5. Slide the Multi-Sync Reducer into it's proper place Sync Reducer by turning them around the opening 6- Set the Clamp the around the sleeve&over the Eccentric Insert and tighten and pipe until they are lined up such that there is "snugly". 7. Set clamp over reducer end on the pipe&tighten enough to create a seal little or no stress applied to the sleeve opening. around the pipe. P,pe Sire Repair Kit Cuff Insert Eccentric Insert Multi-Sync DBF II Fill Clamp 50 MM Pipe XXX2.0 MSZ BLM-2.0 UIZ BLM 5.1x2.0 UIZ 6.0.4.5E URZ MS 4.Sx2.0 41 32 2"FRP XXX2.5 MSZ BLM-2.4 UIZ BLM 5.1x2 4 UIZ 6.0.4.5E URZ MS 4.5x2.4 39 40 63 MM Pipe XXX2.5 MSZ BLM-2.5 UIZ BLM S.Wx 5 UIZ 6.0.4.5E URZ MS 4.5x2.5 38 40 2"LCX XXX2.7 MSZ BLW2.7 UIZ BLM 5.1x2.7 UIZ 6.Ox4.SE URZ MS 4.5x2.7 37 44 75 Mm Pipe XXX3.0 MSZ BLM-3.0 UIZ BLM 5.1x3.0 UIZ 6.0x3.0 N/A 34 48 3"FRP&90 MM Pipe XXX3.5 MSZ BLM-3.6 UIZ BLM 5.1x3.6 UIZ 6.0x3.6 N/A 30 60 3"FRP over 2"FRP XXX3.Sx2.4 M52 BLM-3.6 U12 BLM 5.1x3.6 U12 6.0x3.6 N/A 30 M32 3"LCX XXx3.7 MSZ BLM-3.8 UIZ BLM 5.1x3.8 UIZ 6.W.8 N/A 28 Corrugated Ducting over 1112"Flex XXX4.8x2.0 MSZ BLM-4.6x2.0 UIZ BLM 5.1x2.0 UIZ 6.Ox4.SE URZ MS 4.Sx2.0 33 Corrugated Ducting over 1 1/2"Flex XXX4.8x2.5 M5Z BLM-4.6x2.5 UIZ BLM 5.1x2.5 UIZ 6.0.4.5E U0.ZMS45x2.5 31 Step 9: Fill With DBF II,Insert Fill Plug TOOLS REQUIRED: • Assemble DAG&DBF II(see instructions on DPM website). Gloves and Static Mixer • Purge 1-2 oz. 5/16"Nut driver (for Band Clamps) Fill fitting slowly. DAG Caulk Gun (for DBF II) Note: Use Remote Fill option if access is limited DAGP Caulk Gun (Pneumatic version for DBF II) • Insert fill plug when filling is completed. DAG III Caulk Gun (for DEB V) Clean any spilled DBF It with DBC and dispose of remaining products per local requirements. PRODUCTS NEEDED: DBC Cleaner DBB III Bonder Each DBF II&DBB V come Note: After 1 hour with a Static Mixer the repair job may be DBF II Polysulfide Liquid Fill hydro-static tested DBB V Bonder(for Poly or Fiberglass sumps) FILL Volume: (per repair boot) Volume of DBF II needed = See Table above Volume of DBB III needed = Remote Fill Option: Volume of DBB V needed = The following parts are available to order if you can not properly position the assembled DBF II applicator gun to Parts in kit: "fill"the repair. The Remote Fill parts provide a flexible Bonding Ring UIZ MS 6.0x5.7 CR extension for the filling process. Sleeve USZ 6.0x6.0 Eccentric Insert UIZ 6.OxSee Table RF Adapter 24"tube with male&female ends Multi-Sync Reducer uRZ MS 4.5xSee Table RFA Tube-24 %"Tubing in 24"lengths 5 clamps 3 496,1#80,14 See Table RFA Tube %"Tubing in 200'length roll Fill Port Plug RFA xPlug RFA TubexTube '/�"Tube Coupling Install Instructions RFA xFemale '/"Tube-Female Fill Port end RFA.Male '/2"Tube-Male Fill Port end RFA xPlug %"Tube-Male Plug for fill port