Laserfiche WebLink
IMPORTANT 1.0 TANK SET-UP INFORMATION, <br /> _ <br /> Please read this safety information before WARRANTY AND CHECK-OUT <br /> FORM <br /> beginning set-up. <br /> This product has been installed and will operate in the Warranty and check-out forms were sent to you when <br /> highly combustible environment of a gasoline storage your X76 ETM was shipped. The white copy of these <br /> tank. It is essential that you carefully read and follow forms must be completed and returned to API/Ronan <br /> the warnings and instructions in this manual to protect to validate the warranty. Part 1 of the Warranty and <br /> yourself and others from serious injury, explosion or Check-out Form includes the Tank Set-up Informa- <br /> electrical shock. tion Form. See sample on page 18. <br /> For safety reasons we have taken particular care in Before starting, make sure the following material and <br /> the design of this product to limit power in the wiring information is available. <br /> to the fuel tanks and to keep that wiring physically A. Warranty and Check-out Forms. <br /> separated from other wiring. It is your responsibility to B. Site Preparation and Installation Manual. <br /> maintain the effectiveness of these safety features by <br /> starting up and operating this product in accordance C. Tank Specifications - including tank material, <br /> with the following instructions and warnings. Failure volume, diameter, manufacturer's height to <br /> to do so could create danger to life and property and volume conversion chart. <br /> result in voiding all warranties connected with this D. Tank Tilt Information. <br /> product. Fuel height readings at fill riser and probe riser, and <br /> Warnings their distances from the center tank hole should have <br /> been taken at the time of probe installation and <br /> Do not apply power to the X76 ETM System until its recorded in the site preparation manual. Check Sec- <br /> installation has been checked and found to be in ac- tion 4.0 Component Installation, starting on page 5, <br /> cordance with the instructions outlined in the following for tank tilt information and enter it on set-up informa- <br /> warnings and conditions: as well as, the National tion sheet. <br /> Electrical Code: Federal, State and Local Codes, and If tank tilt was indicated by a difference in fuel read- <br /> other applicable safety codes. ings, enter "YES" on the set-up chart. The X76 ETM <br /> 1. Conduits or wiring troughs from Probes to Control- will calculate the tank tilt information you input from <br /> ler must not contain additional wires. No other the set-up information sheet. <br /> wires are permitted in the same enclosure as Note: Refer to page 9 for Product Label code num- <br /> probe wires. Probe wires must be contained in a bers. <br /> separate, dedicated rigid conduit. <br /> 2. The conduit run from probe to controller must not <br /> exceed 2,500 feet. See installation diagram for the <br /> X76 ETM's correct wire requirements. 2,0 PRODUCT DESCRIPTION <br /> 3. All conduits must enter the controller through pre- <br /> punched conduit holes. Ronan's Electronic Tank Monitoring Systems assure <br /> 4. Do not install the controller in a volatile, combus- you of accurate and dependabe performance no mat- <br /> tible or explosive atmosphere. ter what your application—fuel inventory, intank leak <br /> 5. Installation and use of this product must comply detection, product line leak detection, secondary con- <br /> with the National Electrical Code; Federal State tainment monitoring or vadose and ground water well <br /> and Local Codes: and any other applicable safety monitoring. The heart of the Series X76 ETM system <br /> codes. is an unique memory chip which will not lose program <br /> 6. For information on line pressure, vapor monitoring information or report even when power is shut off. <br /> and other X76 ETM related devices, refer to the Combining an on-board printer, a membrane keypad <br /> X76 LVC Instructions and Operating Manual. and an LCD display, the X76 ETM is a system easy <br /> to operate and simple to understand. <br /> In addition to simple operation, the X76 Electronic <br /> Tank Monitoring System provides advantages be- <br /> cause of two on-board telecommunication interfaces. <br /> This advanced technology allows you to schedule <br /> timely bulk deliveries and provides the convenience <br /> 3 <br />