INSTALL 1992 - Laserfiche WebLink

Home Browse Search

Code Product Code Product tank chart, press ENT.To enter tank tilt, (1=Yes, 2=No) press ENT. If no tank tilt is entered, press 00 None 23 Unleaded 1 TANK NO.to advance to the next tank to be 01 Gasoline 24 Unleaded 2 programmed. If the tank is not tilted, enter the 02 Lead Free 25 Unleaded 3 number of the next tank to be programmed. 03 Leaded 26 Unleaded 4 04 Leaded Gasoline 27 Unleaded Gasoline Press ENT and repeat the preceding process. If 05 Leaded Regular 28 Unleaded Premium the tank is tilted, continue with programming by 06 No Lead 29 Unleaded Regular entering 1 if the probe is between the fill riser 07 Premium 30 Unleaded Super and the center of the tank, enter 2 if it is not, then 08 Premium Leaded 31 XTRA press ENT. Enter the fuel height at the probe 09 Premium Unleaded 32 Toluene riser and press ENT. Enter the fuel height at the 10 Regular 33 Hydraulic Oil fill riser and press ENT. Enter the distance be- 11 Regular 1 34 #2 Heating Oil tween the probe and the fill riser and press ENT. 12 Regular 2 35 Kerosene Press TANK NO. to advance to the next tank to 13 Regular 3 36 Torbine Oil 14 Regular 4 37 Xylene be programmed and repeat the process. 15 Regular Leaded 38 Diesel 1 If fiberglas shell is selected, press ENT when the 16 Regular Unleaded 39 Diesel 2 correct manufacturer and tank model is dis- 17 Super 40 Diesel 3 played on the LCD. Enter the total capacity of 18 Super 1 41 Diesel 3 19 Super 2 42 Diesel 4 gallons (use exact gallons on tank chart), and 20 Super Leaded 43 Jet Fuel press ENT. Enter the number of gallons at 1/4 21 Super Unleaded 44 Avgas height (use the tank chart), and press ENT. After 22 Unleaded j pressing 1 if the tank is tilted. or 2 if the tank is not tilted, press ENT. If the tank is not tilted, Table 6-2:Products codes. enter the number of the next tank to be programmed, press ENT, and repeat the process 6.2 Programming Number of Tanks, Probe for the next tank. If the tank is tilted, continue Code, Tank Type and Size, High Water programming by entering 1 if the probe is be- Level, Initial Product Water and Gas, tween the fill riser and the center of the tank, enter 2 if it is not, then press ENT. Enter the fuel Theft Gallon Limit, Linear Scale, height at the probe riser and press ENT. Enter Hi Alarm and Product Label Code the fuel height at the fill riser and press ENT. Turn the Mode key to program and press F, 290 Enter the distance between the probe and the fill Y P 9 P riser and press ENT. Press TANK NO. to ad- and ENT. vance to the next tank to be programmed and 6.2.1 Number of Tanks: Press F, 70 and ENT. repeat the programming process. Enter the correct number of tanks to be 6.2.4 Manifolded Tanks: If the tanks in the sys- monitored and press ENT. tem are manifolded together, enter the following 6.2.2 Probe Code; Speed of Wire and Rep. information. Press F, 68 and ENT. Enter the Rate: Press F, 71 and ENT. The LCD will dis- tanks' numbers which are manifolded together play the tank number being programmed. Enter and press ENT. Note: Tank information for each the correct Speed of Wire for the probe and manifolded tank must be entered during set-up. press ENT. After you press ENT,the LCD will The X76 ETM will then combine these tanks for display the Rep. Rate. Enter the correct Rep. the purpose of product delivery and leak detect Rate for the probe in the tank being programmed information. and press ENT. The LCD will then return to the 6.2.5 Initial Product(Gas): Press F, 72 and speed of the wire display. Press TANK NO.to ENT. Enter the correct product level, press ENT. advance to the next tank to be programmed and Press TANK NO.to advance to the next tank in repeat. Note: The Speed of Wire and Rep. Rate the system. Note: Use a gauge stick to deter- are located on the top of the probe and should mine initial levels. be recorded on the set-up sheet provided in this manual. 6.2.6 Initial Product(Water): Press F, 73 and 6.2.3 Tank Type, Size and Tilt: Press F, 74 and ENT. Enter the correct water level. press ENT. YP Press TANK NO.to advance to the next tank in ENT. Enter the number of the tank to be the system. programmed and press ENT. Enter the correct tank shell (1=Fiberglas, 2=Steel), press ENT. 6.2.7 Probe Error Warning: Press F, 67 and ENT. Enter the alarm to be activated in case of a If steel tank is selected, enter the inside probe failure, (i.e. O=High, 1=Low, 2=Same) then diameter, and press ENT. Enter the total volume press ENT. For example, if you select 0, the in gallons (use exact gallons on manufacturer's 9