INSTALL 1992 - Laserfiche WebLink

Home Browse Search

Function Key-F: Depress prior to function com- 6.1.1 Time: Press F, 90 and ENT. Enter the Gor- mand codes. rect time, (i.e. 9.23.0=AM, 1=PM) and press ENT. Print Key- PRINT: Used to select copy for(1) In- 6.1.2 Date: Press F,91 and ENT. Enter the cor- ventory Status, (2) Shift Report, (3) Product rect date (i.e. 1-01-90) and press ENT. Enter the Delivery (drop), (4)Alarm Status and (5) Last correct day of the week (i.e. 1=Sun., 2=Mon., Leak Test Report. Enter the number of the report 3=Tues., etc.), press ENT. requested and press ENT. 6.1.3 Name: Press F, 94 and ENT. Enter the Silence Key-SILENCE: Used to reset remote station's name by using the Date Entry key, (1), alarm relays. to advance the alphabet and Data Entry key, Mode Program/Run Key: Provided with a C/CE, to reverse the alphabet.To move right for removable key to eliminate accidental program an entry, press the Command key L0. To move information entry. The key is positioned in the to the left, press Command key Hi. When the cor- Program mode for system start-up and to enter rect name has been entered, press ENT. function values. When the key is positioned in 6.1.4 Address: Press F, 95 and ENT. Enter the the Run mode, all functions can be interrogated correct street address by using the keys but no data entry values can be changed. It is described in Sections 5.0 and 6.0. recommended that the key is positioned in the 6.1.5 City, State and ZIP: Press F, 96 and ENT. Run mode,then removed and kept in the Enter correct city, state and ZIP, now press ENT. manager's office until a program change is re- Press F, 291 and ENT, to clear Calibration quired. mode. Press PRINT, 1 and ENT, and check print- out to verify the correct time, date, name and ad- dress. 6.0 PROGRAMMING INFORMATION No. Function 58 Display Software Revision Enter the set-up information into the controller by 64 Print Set-up Values using the function codes listed in Table 6-1: Function 65 Enter No.of Contacts Codes. Refer to Section 5.0 for keyboard function in- 66 Display Contact Status formation. 67 Set Probe Error Alarm Level 68 Manifold Tanks IMPORTANT:The Mode key must be switched to the 69 Display Tank Information program position in order to enter set-up information. 70 Number of Tanks All system input should be preceded by activating 71 Probe Entry Function 290. This will disable the printer and allow 72 Initial Product(Gas) changes to set-up data without activating warning 73 Initial Product(Water) 74 Tank Type and Size reports or product increases to the system's set-up 75 Leak Detect GPH Threshold data. When changes have been completed, activate 76 Hi Water Alarm Level Function 291 to restore the system to field operation. 77 Linear Scale When set-up information is complete, the Mode key 78 Fuel Label 79 Theft Gallon Limit should be positioned into the Run mode and the key 80 Net to Gross Gallon removed. With the Mode key positioned in the Run 81 Relay#1 (Programmable) mode, functions can be interrogated but no set-up 82 Relay#2(Programmable) input can be changed. 83 Relay#3(Programmable) Information is entered by pressingthe Function key, 84 Relay a (Programmable) Y 85 Start Leak/Theft Detect(Manual) F, then pressing the correct Function Code (i.e.290). 86 Start Leak/Theft Detect(Manual) (see Table 6-1 for function code listings), and press- 87 Set-up Auto Leak Detect Mode ing the Enter key, ENT. Then press data entry keys 88 Enable and Disable Leak Detect Mode and your entered data will be displayed on the LCD. 89 Print Leak Detect Set-up Parameters Now press the Enter key, ENT, to store the changes 90 Time Entry p Y. g 91 Date entry in the controller's memory. 93 U.S. Units to Metric 94 Station Name 6.1 Programming Time, Date, Station Name 95 Station Address and Address 96 Station City and State 290 Begin Calibration and Programming Sequence Turn the Mode key to program and press F, 290 291 End Calibration and Programming Sequence and the Enter key. ENT. Table 6-1: Function Codes. 8