Laserfiche WebLink
DETAIL B <br />SCALE 1 : 6 <br />1.35 <br />Rotate Tank to Change Width x Height <br />his: <br />171431 <br />DETAIL A <br />SCALE I :6 <br />EMBOSS WILL APPEAR <br />ON TOP END AS SHOWN---" <br />Ali fittings are on one <br />side of tank. <br />1:25 <br />9-.25 <br />CIOSSA <br />customs <br />Oiattart In <br />larger <br />Tank Measurement+ Four 811111-in Fitting% l- .25' on eac wasurement ih rt <br />Average WM thi ckness .219 or 713r tr/-) NPT Female <br />100 116 80W8 26%*/{1014/' Ono) 1 W 0 x 2'1.. Spout Three) ii- <br />Fresh I Gray Water Tanks 46 529 42 x 14' x 18' Two) 1 W ' Two) V' <br />42 48. 27 Ws 15 Wx2217 Three) 1 W • Two) IS" <br />NSF International NSF/ANSI Std 61 approved <br />',tedium Density Polyethylene (MOPE) Resin 40 45 35 W x 13' stir Two) 1 W' Two) Yr" <br />Spun Molded 33 37,95 36-v 12' 617W Two) 1 SI" • Two) SS" <br />No seams prevent teaks <br />30 34.5 34 14' ii ¶2's 17 IS' Two) 1 ti• ' Two) 14" <br />Nompressurized <br />Tank must be vented - See websitt for information 25 25.75 33 W it 10' fi ir Two) 1 W ' Two) 14" <br />Stain, Corrosion and Rust Resistant 2.3 26.45 39 SS' x 8 '1.- 5 14%' Two) 1 II' ' Two) W <br />Fresh or Gray Water Use 21 24.15 34's Ts 16' Two) 1 14 '• Two) W <br />20 23 01) 32 Wx 11 Wx 11 ',I' Two) 1 IS" Two) SI" All fillings on same side of tank <br />See CAD drawing for placement 18 207 23'x101c3c17 W One) 1 W Et x 2- t. Spout Three) Si' <br />Balloon Style Fitting 16 18.4 26' x9' x 16' Two) 1 W • Two) tir" <br />Pm-seated and watertight remove membrane for use <br />13 14.95 21"x 9" x 16- Two) 1 W • Two) W <br />Brace lank and t co level surface 10 115 IV x 9' x 14' Two) 1 W' Two) W Do rye hang using straps <br />Do not set weight on lank 7 8.05 23'Y:el-e9': 0E01 liC D x 2' L Spout Three) W <br />Cuttng cr modifying the lank in any way voids anyinil warranty <br />Sanitize tank prier louse to iv. Ate army cletris 5 5.75 17 Wx9 ¶I.Tx 7 One) 1 W' Three) W <br />wwvv.classacustoms.com <br />Class A Customs 1130 County Road 6 Elkhart IN 46514 PH: 574-206-0101 <br />Z2310 <br />\'—TWO MARKS FROM MANUFACTURING PROCESS <br />WILL BE FOUND IN APPROXIMATE LOCATIONS SHOWN <br />ON SIDE SHOWN OP OPPOSITE SIDE. <br />Gm, <br />AMP. R.114sek ras..M.N.Vala <br />POIYEHYLPG <br />'DIMENSIONS IN INCHES <br />DO NOT SCALE DRAWING <br />ged E.s.r.td,t IC an rctat • ra.u......e• tat c••••,......e, <br />al-au rift, atien JE.arr. Inaan. .1.1 Erz.Orili 1"....trave :Nava vnereori I ut. *rob.. 1,......1,1ans a...ft...M., 2. ems, te•cov aarkre,e <br />.41 ai P.* sei nat. ...c.stiwnsktams son am Ws= 1.• itt`atz.,,, • ti-:.ws o c-zaols <br />dn ...Oa 41.4-eaw:Taa,s nal.eirs Nis CY <br />ENCORE NSW <br />DOEFIPSET DRAWINGS IN ACCORDANCE WITH ANSI DRAFTNG MANUAL Y14.5. <br />TOLERANCE UNLESS CFNIERIMSE SPECIFIED: 3 PLACE DECIMALS I .080 HOLE 0 AND SLOT SUM ..050 ANGULAR DIMENSIONS ZO <br />GALLON WATER TANK <br />SHT 1 OF 1