COMPLIANCE INFO_1990-2001 - Laserfiche WebLink

Home Browse Search

• Flanged connections in Dualoy 3000/L underground piping systems are made °� using one-piece flange rings and stub ends which are bonded onto the pipe ends. Both flange rings and stub ends are fabricated by compression molding �j 0 xz A with ANSI B16.5, Cl. 150. Dualoy 3000/L flanged connections are rated to the Insertion depths (X) are typical. Fittin dimensions Nominal Bell Bell Bell Tolerance for centerline -to -face dimensions on fittings with bell -end 4 100 2.88 0.28 4.75 6.66 4.38 - - 3.25 1.0 Bell Bell 6 150 3.88 0.39 7.10 8.53 6.46 - - 3.25 2.4 (cont Pipe Size A B C D E F X, XZ Wt End configurations (in) (mm) (in) (in) (in) (in) (in) (in) (in) (in) (lb) Adapters: spigot x NPT female 2 50 5.65 2.55 2 x 111/2* - 2.00 - 0.70 - 0.5 3 80 6.90 3.65 3 x 8 - 3.00 - 1.00 - 1.3 0 • ^-{ 4 100 7.55 4.65 4 x 8 4.00 1.20 - 1.7 6 150 10.15 6.90 6 x 8 = 6.00 = 1.00 - 4.2 �- E C B J- *NPS x NPT threads per inch. x Flange stub ends* Flanged connections in Dualoy 3000/L underground piping systems are made °� using one-piece flange rings and stub ends which are bonded onto the pipe ends. Both flange rings and stub ends are fabricated by compression molding �j epoxy resins and discontinuous glass fibers. Bolt holes are drilled in accordance xz A with ANSI B16.5, Cl. 150. Dualoy 3000/L flanged connections are rated to the Insertion depths (X) are typical. same pressures as pipe and fittings of the same nominal pipe size. Houston, Texas 77280 2 50 2.75 0.27 2.65 3.91 2.26 - - 2.15 0.5 ° 3 80 2.88 0.28 3.75 5.16 3.38 - - 2.40 0.7 Tolerance for centerline -to -face dimensions on fittings with bell -end 4 100 2.88 0.28 4.75 6.66 4.38 - - 3.25 1.0 The Netherlands 6 150 3.88 0.39 7.10 8.53 6.46 - - 3.25 2.4 • • * For use with flange rings shown in next table. Flange rings 2 50 - 2.78 0.82 6.00 0.75 4* - - 1.0 E 3 80 - 3.90 1.10 7.50 0.75 8 - - 1.6 4 100 - 4.90 1.10 9.00 0.75 8 - - 2.5 6 150 - 7.26 1.25 11.00 0.88 8 - - 4.9 B * Number of bolt holes. Important notice This literature and the information and recommendations it contains are based on data reasonably believed to be reliable. However, such factors as variations in environment, application or installation, changes in operating procedures, or extrapolation of data may cause different results. Ameron makes no representation or warranty, express or implied, including warranties of merchantability or fitness for purpose, as to the accuracy, adequacy or completeness of the recommendations or information contained herein. Ameron assumes no liability whatsoever in connection with this literature or the information or recommendations it contains. A111e1'ullo r Fittings Dimensions in 2- through 6 -inch Sizes for Dualoy 3000/L pipe system Units Fiberglass Pipe Division All dimensions are in U.S. Customary units (inches). Diametric dimensions are maximums. J.F. Kennedylaan 7 No. 7A, Tuas Avenue 3 Insertion depths (X) are typical. Houston, Texas 77280 All weights (lb) are approximate and assume bell -end configurations. Tolerances Tolerance for centerline -to -face dimensions on fittings with bell -end Phone (713) 690-7777 The Netherlands configurations is t I/,s inch. • • Tolerance for angular dimensions is t 10. Listing Telex 38960 AMERON RS Dualoy 3000/L pipe system is listed with Underwriters' Laboratories, Inc., File DERWRITERS' INCA' (qDELABORATORIES, �� MH9162, and with Underwriters' Laboratories of Canada, File CMH715, for underground piping for flammable liquids. End configurations Bell end is standard. Taper angle FAX 03455-75254 The taper angle on all bell and spigot end configurations is 13/40 for 2- through 6 -inch nominal pipe sizes (NPS). Pressure ratings See Dualoy 3000/L Product Data FP265 for pressure ratings. Manufacturing methods Manufacturing plants: Burkburnett, Texas, Spartanburg, South Carolina; Geldermalsen, The Netherlands The fiberglass reinforced epoxy resin fittings shown in this brochure are and Singapore. Bondstrand pipe is also manufactured in Japan and Saudi Arabia. manufactured using a variety of methods as indicated: Filament winding Compression molding Fiberglass Pipe Division Fiberglass Pipe Division Ameron (Pte) Ltd. Post Office Box 801148 J.F. Kennedylaan 7 No. 7A, Tuas Avenue 3 Houston, Texas 77280 4191 MZ Geldermalsen Singapore 2263 Phone (713) 690-7777 The Netherlands Phone 862-1301 Telex 293096 AMERON FPD Phone 03455-73341 Telex 38960 AMERON RS FAX (713) 690-2842 Telex 40257 BONDS NL FAX 862-1302 FAX 03455-75254 Manufacturing plants: Burkburnett, Texas, Spartanburg, South Carolina; Geldermalsen, The Netherlands and Singapore. Bondstrand pipe is also manufactured in Japan and Saudi Arabia. © 1986 Ameron FP266A (RB/88) supersedes FP266 (10/86) and FP266 supplement (1/87) Printed in LLS A. 5M