|
installation
<br /> Piston-lWe beak Detectors
<br /> n'Z.P
<br /> Part No. 1.16035/PLD Part No. 116080
<br /> 'r!*folw,winp 44o.d tam.arc uad tLrou0—t thn Tit Mule to h[i3,.7 otteati,m to the presxn"athLutrda avariwo ri9k 14,4197 or t4 lmr?Cant inrnrrvatirn+nnr.ming the li!e oft;,,Phit
<br /> �������� inZiwtea gb■er.40,Ca hae+?d•'filch wilr uvw rum p.r.w,.l lrfu ry, � i-uiinaEea prn.ez«of a hraaed which�uiJi orcin eau.e tnin,or tona•a!
<br /> �,i{I�iy1� death ex er,betar,rial grope rq dwmnHe if VLn�rnd. injury,.imL'r:a aub■tantinl F'.bpczt,-dauawe if:yntted
<br /> ® ineii au apre.enee otal—rdwhieh e. mows. _pe,mrW lNury, lrtdkxter U74ttuet;or4 on inwtwiwrA9n44 t"rxt.an,r,r mWW.-
<br /> death or.ubatar`ual proxriq deuag_iCiSrrordL natleevolch ora lm 33.0 t but nc!t fQ4W w Pe-56nal lnlU'evh&Ml'da.
<br /> - Before installing leak detector,review the Appl•,Mt= section 1n leak Detector Manual *5191 for
<br /> limitations or restrictions on uszge.
<br /> e THIS 11,TSTRUCTION SHEET SHOULD BE KEPT 1ATITH THE END ITSER OF THE LEAK
<br /> DETECTOR FOR,RE EMNCE.
<br /> t - Tampering with the screws or seals on cut readily if a lar a pipe wrench is used.Replace
<br /> this leak detector r1Ry inhibit opera- functional element tasaembly securely avid replace
<br /> tion and will void warran . tf:.e purnp in the tank.iSee Step 3 before,replacing
<br /> This Red Jacket leak detector is to be installed into the pump.)
<br /> two-inch threaded port located in the top of Iced Jacket3. Examine strasght bore below two-inch thenad fbr
<br /> submemible pumps manufactured after 1963.For infor.-
<br /> ruation coneerninguse with Rl-!d+1'ac',cetpucnpsrntuiufac- corrosionrougha.ess.Iffound tohcrough,smoo+li
<br /> turgid prier to 1963, or oti;er brands of submersible with fine emery paper,
<br /> pumps, contact the factory. 4. Apply UL Classified non•to-ic pipe thread sealant
<br /> e ® For piston leak detector to operate to the twc-inch threads on the leak detector.
<br /> properly, submersible pumping unit, 5. Screw the detector into the pump. Tighbm with
<br /> must be able to produce a minimum of XLP wrench.(Top bex is 1-13116".)
<br /> `l1 psi.
<br /> Do hat,wire submersible pumps to run f' move T8`plugrefrom the tank test pert on top of
<br /> continuously.Red Jacket line leak de- pump (bee Figure1.). -_
<br /> tectors will not perform leak tests on c Apply UL Classified non-toxic pipe thread
<br /> pumping systeIIls tliat run continu- seRlant to the threads on the straight vent
<br /> ously, tune fitting and install.in the"Tank Test"port
<br /> ALL ALR MUST BE OUT OF THE on the pump manifold.
<br /> SYSTEM FOR LEAK DETE(TOR TO b. Align leak detector so that vent opening at the
<br /> WORK PROPERLY. Before installing top of leak detector is as close to tank test port
<br /> leak detector in the pump,fill the sys- as possible.
<br /> tem wit,productbyrunning the pun:p
<br /> and delivering product from each di41- c, Remove plastic thread protector plug from
<br /> penser{startingwith the farthest,frorfl vent par,on leakdei.Fctor, Apply iii,Claesi
<br /> the pump and working to the pump) fied non-toxic pipe thread sealant to Vent tube
<br /> until all air is removed from system, elbow fitting and..nstall it Teak detector vent
<br /> Certain regulatory bodies require the leak detectors to port. Elbow should bepointeddownward
<br /> remair.in the€ystem after the lines have been installed. for bast protection of tubing,(See Figure 1.)
<br /> The lines may be purged of air by back previewing the 7. Install tubing vent ling into botlifittings as shown
<br /> lines with an.inert gas such as helium or nitrogen to a in Figure 1.
<br /> pressure of 35 psi.This may be done at the impact valve MATE SURE BOTH F17TINGS ARE
<br /> lander the dispenser. When this pressure has been TIGHT TO PREVENT PGSSIBLE
<br /> re.{rhed,the leak detector will be in the open position,By LEAD INTO THE GROUND AND/OR
<br /> turning on the piu- p and gradiially bleeding the gas WATER SEEPAGE INSIDE LEAK
<br /> from the line th.*.ough a-valve at the impact valve of the DETECTOR AND TANK
<br /> falrtl est.dispenser, the lime may be purged.of air. 3. Cor nPet power to bump at lnmd center,
<br /> Disconnect power to the submersible � Whei1 manifolding two pumps to-
<br /> pump when installing and removing getter and the use of oi,e leak detector
<br /> gas pressurization equipment. is more desirable use the Red Jacket
<br /> 1. Disconnect power to pump at the lond center. Part No. 038072 Housing. Consult
<br /> Remove the two-inch plug from the top of the Red Leap:Detector Instructions Form No.
<br /> Jacket pum p,If the two-inch plug is found to be so 041,415 for specific instructions.When
<br /> tight that-A cannot be removed, the submersible utilitiiig the Sig-Flu Leak DYtector
<br /> should tie reniuved from the twik turd placed in a with Red Jacket',four-inob submerg-
<br /> vise. R.—move the functional :element :assombly uncle pump, contact Red Jacket for in
<br /> next LA) the pipe plug. The plug should then come stallat.ion inAructionrc.
<br /> 0%&Pr
<br /> 1 , rw3jr rQe➢ _ - 6 -- -- --— Fes'519103/93
<br />
|