COMPLIANCE INFO_2006-2011 - Laserfiche WebLink

Home Browse Search

Secondary Containment System Installation SUMP CONNECTIONS the outside sump wall while pressing the metal ring against the alignment ring on the inside. A. Entry and Termination at the Sump j. Do not disturb assembly until the adhesive is cured. 1. Sump Entry/Termination Fitting with This includes bonding of pipe to the entry fitting and Bonded Fiberglass Alignment Flings installing the threaded outlet fitting. Clean excess ad- hesive from all bonding surfaces. See adhesive kit in- NOTE: Fiberglass ring seals can only be bo^de,: -c a structions for cure times. fiberglass surface. DO NOT install on round ^ cs. '; T k, The use of an industrial hot air gun may speed up the use with series piping. curing process. Do not overheat. a. Determine entry hole locatio^ a~-cc cat entry hole : Remove '/4"plastic threaded outlet protector.Apply ad- sump wall using dimensions'- -ab e 13. (Maximum _e ve to the Y."fitting and screw into the 1/4"threaded allowable offset is 5' ) ---r Tighten to 40 in-lbs or 1'/a-2 turns past hand tight. stalling the fitting,be sure the interstitial space is TABLE 13. Fitting Dimensions excess adhesive. Install a short hose and _. :ess adhesive through the air passage. Size S C n ;exible tubing or hoses to the 1/4°side-out- (in.) r. in.) (in) e �- --cr hoses must be rated to full vacuum. n. Bond F�� - 3x2 6.33 4.00 4.00 o. AfterP rima _e -as been tested, use a concentric 4x3 6,83 4.00 5.00 reducer to bc--`^e cz ^mp entry/termination fitting to the secondary cora-�--en, piping. Do not use a clam b. Using 40-60 grit sanding s, rface.sand the area around shell termination place of the concentric the hole where the ai r-; es t rings will bond to the reducer.See Termination Example below. sump. Lightly sand the i^:gs, Remove dust and wipe Refer to Bulletin No. 62104 for more data€led information. with solvent(optional). BONDED Sump Entry/Termination Fitting Body c. Place two alignment Kros on sump entry/termination fitting and insert through sump wall with the rings on Sump wall the outside of the wall. Locate the'/"threaded outlet rBond Ring to the desired location. ::=or a gravity drain or open / system, the 1/4"threaded outlet should be located at the 6 o'clock position.Leave W'plastic threaded outlet _ protector in place until z"fitting installation. _ - Retaining Ring d. Dry fit primary pipe and rotate the two rings until the . desired angle is reached. Make alignment marks on / the rings and the sump,.-;all. c e. Place one ring over the sump fitting in the inside of the Hole Dia. sump and rotate to the desired angle. Make alignment —"— mark on both the sump wall and the ring. f. Mix one 7014 or 8014 adhesive for each fitting per the instructions in the adhesive kit. Mix in filler to thicken adhesive (fiberglass alignment ring will not seal e Inside Sump properly without filler). a g. Apply adhesive generously, approximately 1/16" thick to the inside and the outside of the sump TERMINATION EXAMPLE using walls where the alignment rings are lo- � SUMP ENTRY/TERMINATION FITTINGS cated. Be sure to coat cut edges of Minimized insertion --------- ------- !! Primary Pipe- the entry hole.APPI a thin coatingof --_= Mak sure air Red Thread IIA adhesive to the bonding surface of the passage is dear Concentric Reducer two rings that will bond to the sump - \ walls. h. Line up rings with alignment marks and press to- gether firmly. i. Slide the metal retaining ring over the inside section of sump fitting against the alignment rings until theyI��U� - are tight against sump wall.(A short section of 4"pipe 1 G may be used to drive the metal retaining ring over the \ ,-Containment Pipe- fitting.)Be sure there is an adhesive bead visible \, Red Thread 11Abetween the rings and the sump wall.The metal \ _Sump Entry/Termination Fitting ring must hold the assembly in position while the ` Spigot x NPT Adapter or Spigot x Spigot Nipple adhesive cures. If the assembly is not tight against Use concentric reducer to connect the sump entry/termination the sump wall,firmly press the entry fitting against fitting to secondary containment pipe;DO NOT USE clam shell termination fittings with this style fitting. RED THREAD IIA Pipe & Fittings — 20