COMPLIANCE INFO_2006-2011 - Laserfiche WebLink

Home Browse Search

I ON Tools required. Drill bit 1/4" diam &5/16" diam,template, hole saw, -17- sandpaper and 5/16" & 7/16"wrench. Doublewall barrier Epoxy powder coated Back plate 1- Locate center of all (pipe/conduit), if possible, on flat SS hose clamp SS Hose clamp section of containment box make sure all fittings will not interfere with each other. Drill a 1/4" diameter perforation at the fitting center. Fasten UniFitting template (See FIG 1-A �I and/or FIG 2-A)with 1/4" bolt&wingnut through the center. �J 4 , a Drill one of 5/16" holes on template and fasten a 5/16" bolt 4 _ &wingnut to fix the template in position, drill the hole positioned 180° across. Using the same method, continue "°`S� 3/4"conduit area 314"Insert with the rest of the perforations.After drilling all the 5/16" Compression ring holes remove the template and repeat the process for all Inside of Sump Outside of Sump other UniFittings. Fig 1-A Fig 1-B 2- Drill out opening for the UniFitting by using properly sized hole saw (seems table below). After drilling opening, sand rough edges with 60 grit. /0 ° a 3- FOLLOW T-F-33-SAND-KIT INSTRUCTIONS TO ABRADE WALL FLAT For B-17 Use Unifitting Hole Saw Min. Saace C/L to CIL B-17 Template 2 1/2"HoleSaw B-17-D (See Figl-B) 2-1/2" 4-1/4" B-33-D (See Fig 2-13) 4-1/2" 6-1/4" Fig 1-C Vulkem of Doublewall Barrier 7 ^f Ci B-17 Fitting, 4-Cutting steps on the B-17 boot requires inserting a rigid conduit inside the B-17Fitting. Back plate Compression z _( 7 1 and hose fitting. Proceed to cut with free-hand away from utility knife.Apply Vulkem ring,insert, t clamp sealant to exterior of containment box where the circumference of the fitting and c mp am makes a seal with box. Insert exterior seal (See FIG 1-C and/or FIG 2-C) Vulkem from outside of containment through bolt holes. From the inside of Inside of Sump Outside of Sump containment install Alcryn boot over bolts followed by a plastic compression Fig 1-D ring with chamfers, (See FIG 1-D and/or FIG 2-D). Vulkem 5-The chamfer on compression ring must be against the Interior Alcryn boot of the B-17 and B-33. Apply vulkem generously to each thread area with glove. Start threading the nuts by hand. Then with 7/16"wrench, start tight- ening the first nut followed by the nut positioned 1800 across. Repeat this method for remaining nuts. Use a torque wrench at a maximum torque B-33-D 10Doublewall Barrier setting of 5 foot pounds (60 Ib. inches). 4 Warning: Do not over torque nuts, follow recommended practices. 4 l 6- Insert the appropriate sized pipe or conduit into the Alcryn boot from Nub a outside of the containment box. Please note: fitting for double wall 4 sumps are designed only for Fiberglass rigid pipe. After the pipe or con- 3"Secondary v Exter&boot Back plate duit has been positioned and tested, fasten the S.S. band clamp around cmrea aping aInterior boot boot tightening to 4 foot pounds (48 Ib-inches) both inside and outside of Fig 2-A Fig 2-B box. Black SS clamp goes on the outside.Apply Vulkem isolation sealant to the exterior black epoxy coated stainless steel clamps approximately 1/4" thick. For B-17 UniFitting place clear insert over each threaded bolt end. u For both B-17 and B-33 fittings apply Vulkem sealant generously to the out- j side nut and bolt areas, leave no metal exposed. Let the sealant form a °_ M1 For B-32.7/33-D "skin"or harden then backfill with approved peagravel per pipe B.34,332.7and/or B-33 Use 4 1/2" manufacturers specifications. Template HoleSaw Fig 2-C Fig 2-D Angled Entries: The UniFitting is flexible enough to allow pipe and 1 conduit from entering the containment box at an angle of 5o in any Apply r M Vulkem ( } direction. ;_ g under and t\ /1 amine � j, stainless Offset Entries: The UniFitting allows pipe and conduit to enter the ° ° sel and 8 , ` containment box at an offset of 1/4" in any direction. 4 o°efP1� and black hose camp. Vukke Vulkem Interior Exterior Round (curved)Surface Entries: NOT ALLOWED L.