|
09-04-'08 10:18 FROM-Western Pump, Inc. 619-236-7406 T-530 P015/019 F-786
<br /> 8014, $024, 8069 069 Adhesive Kits
<br /> 8
<br /> and all adhesive is mixed in from the sides installation Bulletin No.F6000 for additional
<br /> and corners of the can. A smooth uniform installation instructions, 2, When the temperature is between 50°F
<br /> consistency and color indicates adequate and 70`F(10°/21.1°C)joints may be heated
<br /> mixing of the adhesive. For 8 thru 24 inch diameter pipe, a Fiber to accelerate the curing process. Below
<br /> Glass Systems hydraulic or manual come- 50°F (10°C) the joints must be heated to
<br /> If the adhesive becomes warm and begins to along is recommended. Connect two cure the adhesive. Fiber Glass Systems
<br /> set up in the container,safely dispose of the come-alongs to the pipe and pull the joint offers customized electrical heating collars
<br /> container. DO NOT USE THIS ADHESIVE together slowly while firmly hammering on for this purpose. The collars are reusable
<br /> TO BOND A JOINT! the sides of the joint with a rubber mallet or and operate on standard 110/120 VAC or
<br /> 5 pound dead blow hammer, The vibrations 220/240 VAC. Refer to Bulletin Number
<br /> BONDING OPERATION from the hammer blowswill aid joint lock up. F6640, Manual Number F6000, or Manual
<br /> 1. Using a clean paint brush, apply a thin, Continue until joint insertion stops and locks Number F6300 far additional information.
<br /> uniform coat of adhesive to the bonding tight. Take care not to damage the pipe.
<br /> surfaces. First coat the bell and then the 3. When using a heat assisted curing
<br /> spigot bonding surfaces. NOTE:When using a hydraulic come-along, method do not handle or pressurize pipe
<br /> ._._® refer to Manual No.F6000,F6618 or F6619 assemblies until they have cooled to
<br /> for come-along pressure requirements. A ambient temperature,
<br /> Fiber Glass Systems strap clamp kit is also
<br /> available for pipe to fitting connections.
<br /> ADHESIVE DISPOSAL: Once the adhe-
<br /> 3. To ensure joint lock up a pen mark should sive and catalyst have been mixed and
<br /> be placed on the pipe as a visual reference reacted,nothing can be extracted,and it is
<br /> point. The mark is usually made after the
<br /> classified as non-hazardous material. Dis-
<br /> joint has been pushed together snugly but pose of in a normal manner as other solid
<br /> not completely made up. The mark should waste. Excess adhesive and catalyst can
<br /> Note: Completely coat both bonding be placed %to 1 inch from the end of the be mixed, allowed to react, and disposed
<br /> surfaces of the joint and remove any loose female side of the joint. The joint is then of as above. If extra cans of adhesive or
<br /> paint brush bristles in the adhesive. driven together until insertion of the male tubes of catalyst have accumulated with-
<br /> end stops. The mark is used as a visual out the other component to mix and react,
<br /> 2. Align and lock the joint. point of reference between the two halves contact your FGS regional manager.Cata-
<br /> of the joint. lyst tubes,when empty are not subject to
<br /> EPA regulation and can be disposed of in
<br /> 4. Pipe or sub-assemblies may be moved a normal manner. These guidelines are
<br /> after the joints are locked up as long as based on federal regulations. State and
<br /> the joints are not loosened by excessive local regulations and ordinances should
<br /> Y_ bending or abrupt movements. be reviewed.
<br /> 5. When the joints are fully cured the
<br /> assemblies may be handled, pressurized
<br /> For 2 inch diameter pipe, insert the spigot or hydro tested per Fiber Glass Systems'
<br /> into the bell until the tapered surfaces recommendations in Manual No. P6000 ?'::' ,s:''';'r ">`:° "F"'".:x;;'?:;i.;';,.'.::, •'
<br /> touch. Then while pushing, turn the joint "Pipe Installation Handbook" or Manual :<�:?S�' ,'spoll ;:}'of•EF ibr Glas ::Systertis;
<br /> No. F6300"Green Thread Marine-Offshore t '„t. pr „ !„'jjt .r;"?rotliicls•;tr; tt•t<niailly+,:j
<br /> until it locks tight. Normally, one half to a n,,�a �, � �, -
<br /> P Installation Instructions." <�,
<br /> full turn is needed, bold in locked position ,tri', . ,.�'., ;.; a;.::•.s>':.. t
<br /> until excess adhesive squeezes out.
<br /> ADHESIVE CURE eit,•"� 3, �1sy5{+t41P4.s;;, ii •`s
<br /> (I St I rti5f'r 4A ' tQpd°:.iq :st.
<br /> For 3 thru 6 inch diameter pipe, turning is 1. The Time required to fully cure an MAy ?. x:; ,. z.iC = y;,;
<br /> not practical, so align the pipe and push adhesive joint is dependant on the ambientR�:t. ►0ys'
<br /> until the tapered surfaces touch. A driving temperature. The following table shows the -;v ;efteDUnet da�,eVVi(iiftl�'e'
<br /> force must be used to lock the joint. The time required for complete cure at specific 0?¢::;: ,•,;; Y6�sio!";I( t%hfwWw;a
<br /> 'tf plpe tnc Anfpr tion cohtairied-
<br /> additional force can be provided by using a temperatures. 'r. .•:
<br /> piece of hard wood and a hammer, ,I.hgc�I�,Is?,:gene lin<fl)attiie}'ih't is4'notV
<br /> Ambient Temperature vs. ii2Estjir ,f4€ g p .;:ay W�ttah 4i,;
<br /> Time to Pressure
<br /> Threaded and Bonded T.A.B. joints '
<br /> irilied
<br /> [i :;.::'
<br /> Temperature OF Time(Hours) f.: P.,.
<br /> T.A.B, joints are available for 2 thru 6 50(10°C) 18
<br /> inch diameter RED THREAD 11 pipe to 60(15.600 12
<br /> pipe connections. T.A.B. joint installation
<br /> procedures follow the normal bell and spigot 70(21.1°C) 6
<br /> operations of cleaning,adhesive mixing,etc. 80(26.7°C) 4
<br /> as described previously. The threads on the 90(32.3°C) 2 RN015NG
<br /> °bonding surfaces are designed for ease of
<br /> installation and to improve the reliability of 110(43.3°C) 1the bonded joint. See Fiber Glass Systems fp ng sys ms mus no a prsssurzs un S SYSTEMS
<br /> the adhesive jointe are fully cured,
<br /> OTrademark of VSrco UP,Inc. FIBER GLASS SYSTEMS•A NATIONAL OILWELL VARGO COMPANY
<br /> 0 2005,NATIONAL OILWELL VARCO 2700 W.65th ST.,LITTLE ROCK,AR 72209.501-568-4010•FAX 501-568,-4465
<br /> PRINTED IN U.S.A.40MO807 25 S.MAIN ST„SAND SPRINGS,OK 74063.918-245-6651 a FAX 918-245-7588
<br /> i
<br />
|