Laserfiche WebLink
Jul 25 13 08: 10a Eli! IV Contactors 12094W342 p. 4 <br /> e <br /> - -- <br /> Page 2 l 1 <br /> Step 7: install The Eccentric Insert&Multl-Sync Reducer <br /> • Dry fit the Eccentric insert.Make sure it fits properly over the pipe&inside the <br /> sleeve. JUL 2 5 2013 <br /> • Dry fit the Multi-Sync Reducer <br /> • Adjust the positions so that they lineup properly with the Repair Sleeve&Pipe. <br /> Note: A proper fit will not cause extra pressure or force to the sleeve and will <br /> silaw a longer lasting repair:...._._.__.._..._... —I I LTA OEI��6f7'P�Et�T <br /> » once you have the part lined up correctly <br /> 1. Pull back the Multl-Sync Reducer&Eccentric Insert <br /> 2.Apply Vp Tite bonder all around the Eccentric Insert, <br /> 3.Slide Eccentric Into the Repair sleeve In the proper position <br /> 4.Apply Zip Tite bonder all around the Multi-Sync Reducer <br /> 5.Slide the Multi-Sync Reducer into it's proper.place <br /> 6.Set the Clamp the around the sleeve&over the Eccentric insert and tighten <br /> "snugly". <br /> 7.Set clamp over reducer end on the pipe&tighten enough to create a seal <br /> around the pipe. <br /> Pipe Sire Cuff Insert Eccentric Insert Multi-S nc Clam3 4 Ri Id Conduit [Re <br /> UIZ BLS.3.lxl.1 UIZ 3.592.6E RZ M5 2.6x1.1 16 <br /> 1"Ri id Conduit UiZ BIS 3.1x4.4 UI2 3.5x2.6E URZ MS 2.6x1.4 20 <br /> "Flex Pie Uig BLS 3.1x1.6 UIZ 3.54.6 N/A 24 <br /> —E.. lmo <br /> Step 4: Fill With DBF 11,insert Fill Plug TOOLS REQUIRED: <br /> - -Assemble DAG&DBF ll-(see Instructlons on DPM website). Gloves arid-Statle Mixer <br /> • Purge 1-2 oz. 5/16"Nut driver (for Band Clamps) <br /> Fill fitting slowly. DAG Caulk Gun (for DBF 11) <br /> Note: Use Remote Fill option if access is limited DAGP Caulk Gun (Pneumatic version for DBF II) <br /> • Insert fill plug when filling Is completed. DAG 111 Caulk Gun (for'DBR V) <br /> Clean any spilled DBF ii with DBC and dispose . <br /> of remaining products per local requirements. <br /> PRODUCTS NEEDED: <br /> DBC Cleaner <br /> Note: After 1 hour DBB III Bonder Each DBF 11&DBB V come <br /> the repair job maybe DBF 11 Polysulfi lc Liquid Fill <br /> with a Static Mixer <br /> hydro-static tested DBB V Bonderft Poly or Fiberglass sumps) <br /> EILLY-alurne: fn r$ reaali j !p,;, <br /> Volume of DBF Il needed = 9.5 oz <br /> - Volume of DBB III neede-I _ <br /> Remote Fill Option: _...._. _._,._..-._--.. _-,. ....Vdiurne of DBB V neede I _ <br /> The following parts are avallable to order if.you.can not. <br /> properly.position.the assembled DBEII-applicatorgun.to. . ._ Eg '•. n kit: <br /> "fill"the repair. The Remote Fill parts provide a flexible Cuff Insert UIZ BLS 3.1xSee Table <br /> extension for the fitting process. Sleeve USZ 3.5x3.5 <br /> RF Adapter 24"tube with male&female ends Eccentric Insert UIZ 3.5xSee Table <br /> RFA Tube-24 Y:"Tubing In 24"lengths Multi-Sync Reducer URZ MS 2.6xSee Table <br /> RFA Tube Ya"Tubingin 200'length roil 5 clamps 2#44,1#40,2#See Table <br /> Fill Port Plug RFA xPlug <br /> RFA TubexTube Ya"Tube Coupling Install Instructions <br /> RFA xFemale Y"Tube-Fem- ale Fill Port end <br /> RFA xMale Y:"Tube-Mate Fill Port end <br /> RFAXPiu Y:"Tube-1Vlale Ptug for fii!port__.. <br />