Laserfiche WebLink
S-M Z <br /> Page 2 <br /> Step 7:Install The Eccentric Insert&Multi-Sync Reducer <br /> • Dry fit the Eccentric Insert,Make sure it fits properly over the pipe&inside the <br /> sleeve. <br /> • Dry fit the Multi-Sync Reducer _ <br /> • Adjust the positions so that they lineup properly with the Repair Sleeve&Pipe. <br /> Note:A proper fit will not cause extra pressure or force to the sleeve and will <br /> allow a longer lasting repair. <br /> • Once you have the part lined up correctly <br /> 1. Pull back the Multi-Sync Reducer&Eccentric Insert <br /> 2.Apply Zip Tite bonder all around the Eccentric Insert, <br /> 3.Slide Eccentric Into the Repair sleeve In the proper position <br /> 4. Apply Zip Tite bonder all around the Multi-Sync Reducer <br /> 5.Slide the Multi-Sync Reducer Into it's proper place iI <br /> 6.Set the Clamp the around the sleeve&over the Eccentric Insert and tighten <br /> "snugly" <br /> 7.Set clamp over reducer end on the pipe&tighten enough to create a seal <br /> around the pipe. <br /> Pipe Size Re air Kit Cuff Insert Eccentric/Insert Multi-Sync Clam <br /> 3/4"Rigid Conduit MSZ BLS-1.1 UIZ BLS 3.1x1.1 UIZ 3.5x2.6E URZ MS 2.6x1.1 16 <br /> 1"Rigid Conduit MSZ BLS-1.4 UIZ BLS 3.1x1.4 UIZ 3.5x2.6E URZ MS 2.6x1.4 20 <br /> 1"Flex Pipe MSZ BLS-1.6 UIZ BLS 3.1x1.6 UIZ 3.5x1.6 N/A 24 <br /> i <br /> 10 <br /> i <br /> Step 9: Fill With DBF II,Insert Fill Plug TOOLS REOUIIRED: <br /> • AssembleDAG&DBF it(see Instructions on DPM website). - GloVes and Static Mixer <br /> • Purge 1-2 oz. 5/16"Nut driver (for Band Clamps) <br /> • Fill fitting slowly. DAG Caulk Gun (for DBF ll) <br /> Note: Use Remote Fill option if access Is limited DAGP Caulk Gun (Pneumatic version for DBF II) <br /> • Insert fill plug when filling is completed. DAG III Caulk Gun (for DBB V) <br /> • Clean any spilled DBF II with DBC and dispose_ <br /> of remaining products per local requirements. <br /> PRODUCTS NEEDED; <br /> DBC Cleaner <br /> DBB III Bonder Each DBF II&DBB V come <br /> Note: After 1 hour with a Static Mixer <br /> the repair job may be DBF II Polysulfide Liquid Fill I . J <br /> hydro-static tested DBB V Bonder(for Poly or Fiberglass sumps) <br /> FILL Volume: (per reoair boot) <br /> Volume of DBF ii needed = 9.5 oz <br /> Volume of DBB 111 needed = <br /> Remote Fill Option: - — Volume of DBBV needed <br /> The following parts are available to order if-you can.not, <br /> properly position the.assembled DBF Il.applicatorgun to PUIA 10 k + _ <br /> "fill"the repair. The Remote Fill parts provide a flexible Cuff Insert UIZ BLS 3.1xSee Table <br /> extension for the filling process. - Sleeve USZ 3.5x3.5 <br /> „ Eccentric Insert UIZ 3.5xSee Table <br /> RF Adapter 24 tube with male&female ends Multi-Sync Reducer URZ MS 2.6xsee Table <br /> RFA Tube-24 Y2"Tubing in 24" lengths 5 clamps 2#44,1#40,2#See Table <br /> RFA Tube Y2"Tubing in 200'length roll Fill Port Plug RFA xPlug <br /> RFA TubexTube Y2"Tube Coupling Install Instructions <br /> RFA xFemale Y:"Tube-Female Fill Port end <br /> RFA xMale Y2"Tube-Male Fill Port end <br /> -RFA xPlug Y:"Tube=Male Plug for fill port <br />