Laserfiche WebLink
,C'UL/ULC LISTED SECONDARY CONTAINMENT FITTINGS <br />TERMINATION CONCENTRIC REDUCERV) <br />WITH 3/4" NPT <br />3/4" NPT <br />+ TAP <br />Sizes available for Termination Concentric Reducers, <br />with and without tap: 3" x 2", 4" x 3". *6" x 4". <br />450 ELBOW SLEEVE COUPLING <br />SIZES AVAILABLE <br />Belled Side Outlet <br />Threaded Side Outlet <br />NPT Internal Threads(2) <br />3"x2" <br />3"x1" <br />4"x2" <br />3"x11/4" <br />4" x 3" <br />3" x 1 iii" <br />at 150 F <br />4"xt" <br />64.12 MPa <br />4" x 11/4" <br />4„ <br />4" x 11/x" <br />m <br />a n <br />78• F/24* C <br />"Value <br />50 fL <br />2„ <br />15.2 m <br />3„ <br />80 it <br />at 150 F <br />24.4 m <br />64.12 MPa <br />100 It. <br />4„ <br />30.5 m <br />156.51 MPa <br />ASTM D-695 <br />Modulus of Elasticity in Tension at 750 F <br />1.92 x 106 psi <br />1.32 x 104 MPa <br />ASTM D-2105 <br />at 1500 F <br />1.70 x 106 psi <br />1.17 x 104 MPa <br />Ultimate Hoop Tensile Strength at Burst <br />m <br />*NOTE: 6" secondary containment fittings are not UL/ULC Listed. <br />PRESSURE RATINGS <br />a � <br />Bending Properties of RED THREAD 11 Pipe <br />momhw <br />pipe s <br />a n <br />78• F/24* C <br />"Value <br />50 fL <br />2„ <br />15.2 m <br />3„ <br />80 it <br />at 150 F <br />24.4 m <br />64.12 MPa <br />100 It. <br />4„ <br />30.5 m <br />TYPICAL PHYSIC L. P TIE t5) <br />Property <br />Value <br />"Value <br />Test Method <br />Tensile Strength — Axial at 750 F <br />11,900 psi <br />82.05 MPa <br />ASTM D-2105 <br />at 150 F <br />9,300 psi <br />64.12 MPa <br />Compressive Strength — Axial at 750 F <br />22,700 psi <br />156.51 MPa <br />ASTM D-695 <br />Modulus of Elasticity in Tension at 750 F <br />1.92 x 106 psi <br />1.32 x 104 MPa <br />ASTM D-2105 <br />at 1500 F <br />1.70 x 106 psi <br />1.17 x 104 MPa <br />Ultimate Hoop Tensile Strength at Burst <br />Average at 750 F <br />44,000 psi <br />303.37 MPa <br />ASTM D-1599 <br />Long Term Hoop Strength at 750 F <br />Cyclic Pressure (150 x 106 cycles) <br />sl 9,140 <br />p <br />63.02 MPa <br />ASTM <br />at 150d F <br />8,020 psi <br />55.30 MPa <br />Procedure duce A A <br />Thermal Expansion Axial <br />2" 3" 4" pipe <br />1.09 x 10-5 in./in./0F <br />1.96 x 10-5 mm/mm/0C <br />AOSI-TM16-3 <br />Thermal Conductivity <br />2" 3" 4" pipe <br />2.9 BTU/(ft.2)(hr.)(0F/in.) <br />0.42 W/(m)(OK) <br />AOSI-TM16-15 <br />Specific Gravity <br />1.85 <br />1.85 <br />ASTM D-792 <br />Flow Factor <br />Hazen -Williams Coefficient <br />150 <br />150 <br />AOSI <br />(1) A 3" x 2" reducer bushing which is (2) Threaded connections (3) Sharper bends should be eliminated (4) Data not available at time of (6) Pipe is manufactured incompliance <br />not UL/ULC Listed is available for must be made with a to avoid stress concentration which printing. with ASTM D-2996. Refer to general <br />use with the 4" x 3" termination flexible connector. would result in premature pipe failure specification sheet in catalog for the <br />concentric reducer. under pressure conditions. (5) Tests run on pipe samples. D-2996 designation code. <br />7 <br />