COMPLIANCE INFO_2003-2015 - Laserfiche WebLink

Home Browse Search

Spill Containment — OPW EVR Thread -on or OPW/POMECO EVR Multi -Port Spill Containers are - certified for installation on the OPW Phase 1 EVR system: Ail fill ports in these spill. containers feature enhanced 1 bK-2100-EVR vapor tight drain valves that exceed the EVR requirements for a maximum vapor leak rate of 0.17CFH at 2.0 inches H2O. The vapor return spill. containers feature a permanent plug installed in the drain ports, as per EVR requirements. `~Overfill Prevention The OPW.61SO-400C-EVR Series Overfill Prevention Valves are certified for installation.on the -OPW,Phase 1.EVR'system .The va or tight EVR 6150's are designe&to pebvide positive shut-off of product delivery,before an overf llf condition occurs, per EPA requirements," without intervention from the transport driver. The valve features a sealed float. pivot and a threaded lower tube connection; and exceeds the EVR requirement for a maximum vapor leak rate of 41.,17CFH at2.0 inches H2O, The 61 SO-EVR Series Valve .is installed in the base of the OPW EVR Spilt Container with the' patent 61JSK Jack Screw device. This configuration allows Irquid'in the spill container to be drained directly into the drop tube, thereby isolating the drain valve from the tank ullage, eliminating a notorious leak point in previous systems. Tank Bottom 'Protector —The OPW/POMEC® 6111-1400 Tank Bottom Protector is EVR certified for installation at the bottom of the overfill prevention valve drop. tube to help prevent the underground storage tank from.sustaining damage from erosion or tank gauging sticks. .. BAIN oat and 233 Extractor - The OPW 53VML Ball Float, 233 Extractor and 61Tfiii Erop Tube configuration can be installed as an alternative to the 61 SO Overfill application. The installation of the Ball Float/Drop Tube system is identical to the 61 SO Overfill Valve on the OPW Phase 1 Vapor Recovery System. Rotatable Swivel Adapfors (Fill and Vapor) - OPW EVR Rotatable Swivel Adaptors are certified S. 4.n a �. fo, instaila�ion on the fill and vapor ports -on -the OPEN Phase 1 EVR sysiern. OPW Swivel_ Adaptors - Erovide 360 degrees of rotation of any product or vapor recovery elbow to prevent the adaptors f rom loosening^on the spill container risers. OPW Swivel Adaptors exceed the EVR re uirementto maintain a miri.imurn 360 -degree rotation with an average static torque not to excee 108 inch- pounds (9.foot-pounds), The enhanced poppet system on the OPW .61 VSA-EVR vapor swivel adaptorzprovades a vapor tight seal when closed, per EVR requirements. t Adaptor Tool =An OPW 61 SA -TOOL is required to ensure proper' installation of OPW Rotatable Swel Adaptors, spill- containers and threaded riser adaptors,p er -EVR requirements. The 51SA T(01: mdkdes provisions for the use of a torque wrench to facilitate accurate installation Dust'Caps (Fill & Vapor) ® OPW EVR Dust Caps are certified for installation on OPR.Certified Rotatable Adaptors. OPW EVR Certified Dust Caps feature enhanced ribbed seals and increased sealing forces to provide a bubble -tight seal, per, EVR requirements. Available in Duratuff or low -profile metal models. M is required to provide a Pr sure Vacuum Vent The . Phase 1 EVR system. The daptor) - An OPW FSA -400 Threaded Riser Face Seal ue sealing surface on threaded pipes where a gasket sea[ 100 is installed on the fill pipe riser below the spill face for the drop tube flange on the 61 SO-4000-EVR ). is also required on tank gauging risers, though is adaptors. PW 623V Pressure Vacuum Vent is certified for installation on the �23V°s are installed on the top of the vent pipes for underground and-intemaf wire-screen°are''designed to protectthe'tank vent ` ` cage from water, debris or insects. A normally closed poppet in ned' pressure or vacuum setting to allow the tank to vent. The entof a maximum vapor leak rate of 0.17CFH at 2.0 inches H2O.