COMPLIANCE INFO_1995-2006 - Laserfiche WebLink

Home Browse Search

RIGID CONDUIT ISEE NOTE 7.) BARRIER GROUND CHASSIS GROUND AC NEUTRAL AC LINE EMC MONITOR E RIGID CONDUIT J� i I +—+ 1�•o.la (SEE NOTE 7.) \I \I \ II \I l INPUT EXTERNAL (SHIELDED DEVICE CABLES) 1 WARNING: IN INSTALLATION AND USE OF THIS PRODUCT, COMPLY WITH THE NATIONAL ELECTRICAL CODE; FEDERAL, STATE AND LOCAL CODES. IN ADDITION, TURN OFF POWER AND TAKE OTHER NECESSARY PRECAU- TIONS DURING INSTALLATION, SERVICE AND REPAIR TO PREVENT PERSONAL INJURY, PROPERTY LOSS AND EQUIPMENT DAMAGE. 1 WARNING: DISCONNECT ALL POWER BEFORE MAKING ANY CONNEC- TIONS TO PREVENT DEATH, SERI- OUS INJURY, EXPLOSION, OR ELECTRICAL SHOCK. MONITOR MUST NEVER BE OPERATED UN- LESS THE FRONT COVER IS CLOSED OVER THE BARRIER TER- MINALS IN THE INTRINSICALLY - SAFE AREA. NON -HAZARDOUS AREA RIGID JUNCTION CONDUIT BOX ISEE NOTE 7.) RIGID CONDUIT NOTES: IIa 1. WIRING TO PROBES AND SENSORS MUST BE THWN GAS AND OIL RE- SISTANT SIZES FROM AWG #18 TO AWG #14. BARRIER GROUND WIRING MUST BE AWG #12 OR LARGER. 2. CONNECT WITH#12 AWG (OR LAR- GER) CONDUCTOR THE BARRIER GROUND TO THE EARTH GROUND BUS AT THE POWER DISTRIBUTION PANEL. 3. G DENOTES FIELD WIRING CON- NECTION USING WATERPROOF CONNECTORS SUPPLIED WITH THE PROBE(S) AND SENSOR(S). I I I I HAZARDOUS AREA I I 1 I 1 WEATHERPROOF JUNCTION BOX 11 PER PROBE) FROM PROBE I} � wluEE WEATHERPROOF, JUNCTION BOX )1 PER SENSOR) FROM SENSOR I WEATHERPROOF JUNCTION BOX 11 PER SENSOR) IAI FROM VAPOR SENSOR WEATHERPROOF JUNCTION BOX 11 PER SENSOR) ni GROUND- �_ �wo�tiP' WATER SENSOR I 1 I I 4. INTRINSICALLY SAFE WIRING SHALL BE INSTALLED IN ACCORD- ANCE WITH ARTICLE 504-20 OF THE NEC ANSI/NFPA 70, 1990. 5. TO MAINTAIN INTRINSIC SAFETY AND PROPER SYSTEM OPERATION, PROBE AND SENSOR WIRING MUST BE INSTALLED WITHIN SEALED CONDUIT. 6. ELECTRICAL RATING POWER IN- PUT — 120 VAC, 50/60 HZ, 600 WATTS MAXIMUM. 7. SEE FIGURE 8 IN THIS MANUAL FOR ACTUAL LOCATION OF CON- DUIT ENTRY INTO EMC MONITOR. - n^!�noouuuot �y @ l nn00000� ouo ou'000l ■ n/in000aoonoB'000l �■ . Irx f (nlinoou0000000nol n__ o ■■@rr�nremrrnnas� �> E RIGID CONDUIT J� i I +—+ 1�•o.la (SEE NOTE 7.) \I \I \ II \I l INPUT EXTERNAL (SHIELDED DEVICE CABLES) 1 WARNING: IN INSTALLATION AND USE OF THIS PRODUCT, COMPLY WITH THE NATIONAL ELECTRICAL CODE; FEDERAL, STATE AND LOCAL CODES. IN ADDITION, TURN OFF POWER AND TAKE OTHER NECESSARY PRECAU- TIONS DURING INSTALLATION, SERVICE AND REPAIR TO PREVENT PERSONAL INJURY, PROPERTY LOSS AND EQUIPMENT DAMAGE. 1 WARNING: DISCONNECT ALL POWER BEFORE MAKING ANY CONNEC- TIONS TO PREVENT DEATH, SERI- OUS INJURY, EXPLOSION, OR ELECTRICAL SHOCK. MONITOR MUST NEVER BE OPERATED UN- LESS THE FRONT COVER IS CLOSED OVER THE BARRIER TER- MINALS IN THE INTRINSICALLY - SAFE AREA. NON -HAZARDOUS AREA RIGID JUNCTION CONDUIT BOX ISEE NOTE 7.) RIGID CONDUIT NOTES: IIa 1. WIRING TO PROBES AND SENSORS MUST BE THWN GAS AND OIL RE- SISTANT SIZES FROM AWG #18 TO AWG #14. BARRIER GROUND WIRING MUST BE AWG #12 OR LARGER. 2. CONNECT WITH#12 AWG (OR LAR- GER) CONDUCTOR THE BARRIER GROUND TO THE EARTH GROUND BUS AT THE POWER DISTRIBUTION PANEL. 3. G DENOTES FIELD WIRING CON- NECTION USING WATERPROOF CONNECTORS SUPPLIED WITH THE PROBE(S) AND SENSOR(S). I I I I HAZARDOUS AREA I I 1 I 1 WEATHERPROOF JUNCTION BOX 11 PER PROBE) FROM PROBE I} � wluEE WEATHERPROOF, JUNCTION BOX )1 PER SENSOR) FROM SENSOR I WEATHERPROOF JUNCTION BOX 11 PER SENSOR) IAI FROM VAPOR SENSOR WEATHERPROOF JUNCTION BOX 11 PER SENSOR) ni GROUND- �_ �wo�tiP' WATER SENSOR I 1 I I 4. INTRINSICALLY SAFE WIRING SHALL BE INSTALLED IN ACCORD- ANCE WITH ARTICLE 504-20 OF THE NEC ANSI/NFPA 70, 1990. 5. TO MAINTAIN INTRINSIC SAFETY AND PROPER SYSTEM OPERATION, PROBE AND SENSOR WIRING MUST BE INSTALLED WITHIN SEALED CONDUIT. 6. ELECTRICAL RATING POWER IN- PUT — 120 VAC, 50/60 HZ, 600 WATTS MAXIMUM. 7. SEE FIGURE 8 IN THIS MANUAL FOR ACTUAL LOCATION OF CON- DUIT ENTRY INTO EMC MONITOR.