COMPLIANCE INFO_1997-2006 - Laserfiche WebLink

Home Browse Search

OPW 60 VS SER, -ES VAPOR 1 i VALVES a The 60VS Series is similar to the OPW 60ti'S1 C-1001 60V Series of Vapor Line Shear—.._^_._._.u , G. Valves. They are designed to breal__._.__.._...__`� ��}OI' �1�'2r ticIth at the shear groove in the event the at Thretrds" dispenser is dislodged, helping to pre- Same features as the 60VSP-(000 plus: vent damage to underground piping. ®Externally threaded on outlet However the 60VS Series has addition- �+ al features not found in the 60%* Series. end for secondary containment E connection of underground i in^ The 60VS Series has a 1" connection at the inlet for dispenser piping and an 11/5" at the outlet end to accommodate 11/-," underground vapor lines. An air test port is also included to give access to the vapor lines without breaking pipe joints. At the dispenser inlet end, two connections are available (offering a convenience of choice for installa- tions). A connection through the top of the valve or the side may be made. A plug is shipped with the valve in order to plug off the opening not used. The mounting connection, below the shear groove, has three drilled and tapped holes for mounting to a stabiliz- er bar. All 60V and 60VS models have all important mounting connection wove the shear groove as well. Mounting above the shear Groove is important on vapor lines because of the use of flexible pipe above this point. The shear section must be isolated so - that it is the weak point in the line. OPS%' 60N"S-1000 "Line Saver" Same features as the 60V-1000 plus; • l lh" connection to underground piping • Air test port to enable vapor line testing without breaking pipe connections ® Choice of top or side inlet connection ® Stabilizer mounting connection OP`s' 60VSP-1001 ;`Vapor Saver— Same features as the 60VS-1000 plus; ® Double-poppeted design helps prevent vapor loss in the event the dispenser is toppled- • - ..-,:_. pp Materials Body: cast iron Discs: M-19 Inlet thread size: l" NPT internal threads Outlet thread size: 114- internal threads Ordering Specifications Product No. length in, mm. 60VS-1000 631/32" 111 60VSP-1001 63%31" 177 60VSPC-1001 63%32" 171 Dimensions IMPORTANT: OPW products should be used in eom- pli:.;e %ith applicable federal. state and local laws and r;sclationi. Product se'caion should be based on ph%iical spe-ideations and limitations and compatibility with the en%ironntent and materials to be handled. OPW.%IAKES NO w:4RRA�7Y OF FITNESS FOR A PARTICULAR USE. All illustrations and speeifcea- tioni in this literature are biied on the latest product information available at the time o f publication. OPWWy rciencs the richt to ntake:h�msat any time in prices, mate -tali. specifications and models and to discontinue models w ithout notice or oNigation. 2.- In. mm A 11 %32" 34 B 631h2" 177 C 2n/1s" 68 0 11/2" 38 E 217/32" 73 F In/Is" 43 G 215/I6" 75 IMPORTANT: OPW products should be used in eom- pli:.;e %ith applicable federal. state and local laws and r;sclationi. Product se'caion should be based on ph%iical spe-ideations and limitations and compatibility with the en%ironntent and materials to be handled. OPW.%IAKES NO w:4RRA�7Y OF FITNESS FOR A PARTICULAR USE. All illustrations and speeifcea- tioni in this literature are biied on the latest product information available at the time o f publication. OPWWy rciencs the richt to ntake:h�msat any time in prices, mate -tali. specifications and models and to discontinue models w ithout notice or oNigation. 2.-