COMPLIANCE INFO_2009-2010 - Laserfiche WebLink

Home Browse Search

CNI Man ufacturionstallation. Operation and Maintenar*Manual (IOM) Applicable to Executive Order VR -1 04-D Phase I EVR Equipment Installation Check List for Installing Products per ARB Executive Order VRA 04-D (continued) Yes/No Initials 5. Fill Riser — Is the EMCO Wheaton Retail Al 100EVR Guardian Overfill Prevention Valve installed with the correct EMCO Wheaton O-ring securely in place and the flared end of tube on top of the riser? (New installation and replacement O-ring are #569461.) Note: The EMCO Wheaton Retail All 100EVR Guardian Overfill Prevention Valve must be cut to the correct length and assembled per manufacturer's instructions before installing into the 4 inch tank riser. 6. Are the Containment Assemblies installed onto the 4 inch tank risers Yes/No Initials using a Fire Marshall approved thread sealing compound on the upper male threads of the 4 inch riser pipe and torqued to: • the indicated torque value from Table 1 and 2 for CON 1-31103 and CON2-31103 containments; • the indicated torque value from Table 3 and 4 for 205X-31103 and 214X-31103 containments? 7. Is the Jam Nut(s) installed in the lower set of threads of the Fil-Spil Yes/No Initials oval flange (CON2-31103), or the bottom section of 205P-31103 or 214P-31103 containment, and torqued down on top of the drop tube flare to 45 foot-pounds? 8. Have the 4 inch Containment Nipple(s) been cut to the correct Yes/No Initials lengths and have a flat, square cut across the top of each end, as well as the appropriate threads cut into the ends of each? 8.a. Have the 4 inch Containment Nipple(s) been installed into the Yes/No Initials appropriate flanges using a Fire Marshall approved thread sealing compound on the lower male threads of the 4 inch Containment Nipple and torqued to 170-175 foot-pounds? 9. Are the appropriate Product and Vapor Swivel Adapters (p/n Yes/No Initials A0030 -124S and A0076 -124S, or A0030-124 and A0076-124) installed onto the 4 inch containment nipple(s) with the flat gaskets in place, and torqued to 35 foot-pounds? 9.a. Are the Product Swivel Adapters (p/n A0030 -124S or A0030-124) Yes/No Initials and Vapor Swivel Adapters (p/n A0076 -124S or A0076-124) set screws installed with LocTite #222MS and torqued to 20 inch -pounds? 10. Are the CNI Mfg. Dust Caps (p/n 64 product, and 611 -VR -3 vapor) Yes/No Initials and CNI Mfg. Gaskets (p/n 65) installed onto the appropriate Swivel Adapters? 11. Are the drain valve(s) installed and bottomed out, then turned an Yes/No Initials additional 360'legrees with the cap screwed back on until finger tight? 12. For CON1-31103 and CON2-31103 containments: Are the six Yes/No Initials bolts for the 3 Piece Bellows Hold Down Clamp (p/n STP -33) torqued to. 10 foot-pounds? page. Continued on next 15627 ARROW HIGHWAY, IRWINDALE, CALIFORNIA 91706 PHONE (626) 962-6646; Our OF STATE CALLS (800) 4CN1-MFG; FAX (626) 962-4854 11 WEBSITE: WWW.CNI-MFG.com EMAIL: INFOO)CNI-MFG.COM