COMPLIANCE INFO_2000-2009 - Laserfiche WebLink

Home Browse Search

is • • Installation of Model S1300 IC is detailed in this sec- tion and Figure B (see page 30). Reference Figure C, (see page 30) for Model S1300 14C circuit diagram. Model SB0011C Shown o 0 (D-- ��-- Normal Light i© O AlarBell larm Silence Test C}BA� unon?Autlible Alarm rm AlaLights Alarm Test Power Circuit � VoO Sensor Circuit (To 120 Volts AC) Alarm Contact (To Sensor Assembly) To Gnwnd Switch Circuit Power Circuit Automatic Telephone (To 120 Volts AC) Phone Dialer Line Model SB0014C1 and S110014C4 0 o 0 (D-- Normal Light Normal Light Alam,Lights O AlarBell larm Silence Test C}BA� unon?Autlible Alarm U L Low Voltage High Voltage (Intrinsically Safe) Conduit Hubs Conduit Hub D1. Location H� Low Voltage High Voltage Conduit Hubs (Intrinsically Safe) Conduit Hub AWARNING Locate Control Panel in a Non- Haz- ardous Area Where an Explosive Environment Will Never Exist. • Control panel can be wall mounted using the provided mounting hardware. D2. Power Circuit • All wiring must be in accordance with local codes. • Control panel is pre -assembled and ready to wire. ❑ A 120 volt AC power source is required. Model SBOO11C Shown o (D-- "n Normal Light Normal Light O O�d O Power Circuit Ground LL] Alarm Light (To 120 Volts AC) Lug rm AlaLights Alarm Test � VoO Alarm Bell Silence Button Alarm Alarm O Alarm Bell Silence Test Button Alarm Bell Button O O H� Low Voltage High Voltage Conduit Hubs (Intrinsically Safe) Conduit Hub AWARNING Locate Control Panel in a Non- Haz- ardous Area Where an Explosive Environment Will Never Exist. • Control panel can be wall mounted using the provided mounting hardware. D2. Power Circuit • All wiring must be in accordance with local codes. • Control panel is pre -assembled and ready to wire. ❑ A 120 volt AC power source is required. Model SBOO11C Shown o y t'. "n Normal Light Normal Light O O�d O Power Circuit Ground LL] Alarm Light (To 120 Volts AC) Lug To Ground Alarm Test • Power circuit wiring (contractor provided) enters the left conduit at the bottom of the control panel and is con- nected to terminals L 1 and L2. • Circuit breaker (contractor provided) common to other devices is recommended. ❑ This increases probability tank owner will be aware of a tripped circuit breaker. • If there is no power to the control panel, the alarm bell and other warning devices cannot be activated. • In areas where extreme line transients occur, additional surge protection should be installed on incoming supply source. D3. Sensor Circuit • Pre -assembled reservoir sensor is ready to wire (con- tractor supplied) to the control panel. ❑ For intrinsically safe wiring, use 16 AWG or 14 AWG type THHN or type MTW (contractor supplied) for Model SB control panels and SP switch panels. ❑ For UL rated applications, the maximum wiring dis- tance between the sensor and control panel is 900 feet. • Wiring for sensor circuit enters right conduit at bottom of control panel and is connected to terminals S 1 and G1. Model SB0011C1 and SB0011C4 Low Voltage High Voltage (Intrinsically Safe) Conduit Hubs Conduit Hub 0 O Normal Light Normal Light O Alarm Light Alarm Bell Silence 777777 Alarm Test Bunoiulton ?.udible Alarm Bell Silence Button Alarm Test Button Alarm Low Voltage High Voltage (Intrinsically Safe) Conduit Hubs Conduit Hub Low Voltage High Voltage (Intrinsically Safe) Conduit Hubs Conduit Hub • On four circuit control panel (Model S130014C) there are four terminal pairs. • Connect a separate sensor to each terminal pair ❑ S1, G1 ❑ S3, G3 ❑ S2, G2 ❑ S4, G4 Important: On the four circuit control panel, if less than four monitoring circuits are used, a jumper wire is re- quired to separately connect each unused terminal pair. D4. Optional Wiring Device Circuit • Tank owner may specify additional warning devices to be provided by contractor. ❑ Optional warning device circuits enter panel at the center conduit. 17 Normal Light Alarm Light Alarm Bell Silence Button Alarm Test Button Alarm Bell o Low Voltage High Voltage (Intrinsically Safe) Conduit Hubs Conduit Hub • On four circuit control panel (Model S130014C) there are four terminal pairs. • Connect a separate sensor to each terminal pair ❑ S1, G1 ❑ S3, G3 ❑ S2, G2 ❑ S4, G4 Important: On the four circuit control panel, if less than four monitoring circuits are used, a jumper wire is re- quired to separately connect each unused terminal pair. D4. Optional Wiring Device Circuit • Tank owner may specify additional warning devices to be provided by contractor. ❑ Optional warning device circuits enter panel at the center conduit. 17