Laserfiche WebLink
FROM WILLIAMS FAX NO. : 9167140059 Feb. 02 2004 01:59PM P5 <br /> ' <br /> en%Aroff Installation instructionsFlexible Ent Publication: P-081.5070 <br /> Boots Issue Date: 0$-10-01 <br /> Supersedes: 3.01-0i <br /> FIOXIble Entry Boots <br /> These one-piece rubber boots are designed to seal pipe and conduit entries for both flat and curved surfaces. For proper <br /> installation,the appropriate size fabrication template should be used for acc <br /> hole saws must be used for the given Flexible Entry pont size, urate hple drilling. The recommended sites of <br /> Step#1 <br /> Locate the center entry point in Step#Z <br /> the fiat wall section of the sump , Drill out the entry boot opening <br /> base and drill a 5/16"hole. by using the appropriate size hole <br /> Install the Entry Boot Template saw. After drilling out opening, <br /> to the sump base wall using a clean rough edges with a razor <br /> 1/4"bolt and nut. Drill out one knife or deburing toot. <br /> hole of the appropriate bolt hole Hole Saw Flexible Entry Eluots <br /> circle for the size boot to to 1-&Ir Small profile fEe 30 5 <br /> installed using the same 5/16" ZW targe profile Fww75 <br /> drill bit. Insert a second 1w 2.3/&• FEa-30So,3100,3750,3137 <br /> bolt and nut through this hole to 3' FEB-5150 <br /> secure the template. Continue 4-1/4- F'E3-6150,6200,t <br /> to drill the remaining holes of 1 5-1/2" FEB-7360,7.390,7400 <br /> the bolt hole pattern. After 5-1/2' SAB-7400 <br /> drilling,remove the template 5 1/Y GDB-4515,4520,4530, <br /> from the sump base wall. 7450 <br /> Sabra Saw FEB-Mo <br /> Step#3 Strop <br /> Install the entry boot from out- i 44 <br /> side the sump by inserting the Using the proper nut driver, <br /> studs through the bolt holes, tighten all of the nuts evenly and <br /> From the inside of the sump, firmly To prevent deforming <br /> install the compression ring boots,do not over tighten nuts, <br /> over the studs and install nuts If a torque wrench is used,the <br /> by hand. setting should be 60 in.lbs. <br /> Step#5 Angled Entries <br /> insert the appropriate sized pipe <br /> or conduit into the flexible boot The flexible entry boot is <br /> from the outside of the sump. designed to permit angled pipe <br /> After the pipe or conduit has or conduit entries up to is,off <br /> been positioned,install the the centerline. Angles greater <br /> band clamp around the boot than 15 could prevent the boot <br /> and tighten to from sealing around the pipe <br /> 30 in.lbs. or conduit,and will void the <br /> product warranty. <br /> Rb"Ims Surkim <br /> WARNING.~ Flexible Entry Boots may be <br /> FK—P.affrglass cleaning solvents away from boots „tailed on round surfaces which <br /> reater then 30". <br /> s of sotvOltts could cause severe damage. The instave a llation meterprocedures are <br /> the some as described above <br /> except,extra care shall be taken <br /> to properly hand sand the surface <br /> to be bonded.Make sure all raised <br /> sections of FRP are minimized and <br /> remove all sharp edges.The SMB" <br /> IMPORTANT holt holes should be mado sl-ighdy <br /> The recOmmended hole saw size must always he used larger after initial drilling.This can <br /> for proper installation of the Figxible lEnsyy Boat and be accomplished by moving the <br /> 571 B"bit from side to side in each <br /> maintain the product warranty. <br /> ooh hole after the Entry Boot Tem- <br /> PlateA hydrostatic test crust be performed to n eaal�nut in stages so thn removed, en <br /> ensure a positive seal. boot flange and compression ring <br /> can evenly conform to the rounded <br /> surface and achieve a positive seat. <br /> =01111111,10 <br /> Environ Products,Inc. • P.O.Box <br /> 320 ® Smithfield,NC 27577-0330 a lel:(919)3sa-8400 • Fax:(919)359-3887 <br /> Customer Service:(800)833-1883 • WWW.env roduct.com• <br /> P Q Copyright 2001 <br />