COMPLIANCE INFO_1999-2001 - Laserfiche WebLink

Home Browse Search

RAPID SET CONTAINMENTPIPING Table 1 Nurnber of Containment Fittings You Can Bond Approx. Number of Fittings Type of Fitting Size: 3" 4" 6" 90 elbow 90 1.5 1 . 45 elhow 30 1.5 1. Ipr 31 1.0 0. coupling 1.5 1. termination fitting -Bonding and Assembly* for Containment Piping I Ise only I)S-1014 adhesive manufactured by Smith fiberglass Products for installing RAPID SFT containment piping systems. Do rtof use DS -1014 adhesive on prod- uct (primary) piping. Note: Below 70' f, DS -1014 adhesive may he difficult to rnix. f'rewarm if reclrrired. Fordetails-on �ditesivemiX ►)g and surface cIeanitlg, refer to the hondir g procedures in the-i►t- structioili sheet included With. each 1)S 1014 kit and in Manual No._112160. Thoroughly mix all of the adhesive base with all of the adhesive hardener. Do not at- tempt the split a kit. The adhe- sive should have a uniform Collsistencv. After the pipe has been sanded or scarfed, further preparation is not required for bonding unless contaminated with oil, grease, hand prints, etc Aftcr cleaning apply a thick coating (%." mininiu►n) of adhesive to the socket (hell) area of tite fitting. Liberally coat the flanges (flat bonding surfaces) of both halves of the fittings with ad- hesive (/,,.° minimum thickness) (see fig. 4). Next, apply a thick coating ntinitntirn) of adhesive to the sanded nmfaces Of the pipe ends. Table 2 US -1014 Adhesive Cure lime 1 Pot Life ( Tirne to Pressure Temp. ("F) I (minutes) !I (minutes) 0 0.9 45 0 0.9 .55 9 0.6 68 0 0.9 76 0 0.9 88 103 Refer to Table 1 for the nunther of fittings Which can he bonded with each DS -1014 kit. Assemble with the fitting half containing the threaded inserts on the hotto►n. No YI FS: • 'I he stir stick supplied with the adhesive kit works wc1l as an applicator. • 'fwo-piece containment fit- tings reclr►ire more adhesive than is normally used with 60 90 50 7.5 30 39 20 31 17 23 14 When starting the belts, allow the bolt to start with ►nininial pres- sure on the tool. F'xcessive pres- sure may push the insert from the fitting. "lighten the bolts alter- nately and With equal force. I)cr not exceed S ft -1/7's of forcltte! The flanges of the fitting should fit so that there is no gap. Take care not to dishnh a com- pleted contaiunient piping joint when assembling additional joints. The adhesive mtist he fully cured before applying stress to assembled joiril:s. Apply adhesive to o ' O '0 holt► halves and % to pipe (1/] 6" ruin thickness) '.�,;I Pipe must fit snugly into fitting socket so that no gap exists 1 I _ ► r Smith hiberglass i'roducts bell and spigot joints. Use the bolts supplied With the fitting to assemble the fitting to the pipe. Use of and air or electric wrench With a magnetic socket Will greatly facilitate assembly. Magnetic sockets are available from Smith fiberglass Products. 3 • -Adhesive Cures (_:tire tune depends on ambient temperature (see Table 2). Use of external heat (such as bot air guns) Will shorten the cure titles. External heat is essential when installing at temper - attires below 45° V. Do not use an open flame to cure the adhesive. I lot spots Inay cause tile: adhesive to overheat, re- sulting ill a had hoed. Pipe sections should not be handled or stressed until the gine line has returned to ambient tem- perature. QPrecautions • Avoid contact with the adlte- sive and hardener, since they can cause skin and eye irrita- tion. Gloves and eye protec-