COMPLIANCE INFO_2008-2010 - Laserfiche WebLink

Home Browse Search

t UPCF UST Monitoring Plan —Page 1 Instructions Complete a separate UST Monitoring Plan for each UST monitoring system at the facility. This form must be submitted with your initial UST Operating Permit Application and within 30 days of changes in the information it contains. Your local agency may require you to obtain approval prior to installing or modifying monitoring equipment.. (Note: Numbering of these instructions follows the data element numbers on the form..) 490-1 TYPE OF ACTION—Check the appropriate box to indicate why this plan is being submitted. 490-2 PLAN TYPE—Check the appropriate box to indicate whether this plan covers all,or merely some,of the USTs at the facility If the plan covers only some of the tanks,identify those tanks in the space provided[e g,by using the Tank ID#(s)in item 432 of the USTOperating Permit Application—Tank Information Form(s)J. 1, FACILITY ID NUMBER—This space is for agency use only. 3. BUSINESS NAME—Enter the complete Facility Name 103 BUSINESS SITE ADDRESS—Enter the street address where the facility is located,including building number,if applicable.Post office box numbers are not acceptable. This information must provide a means to locate the facility geographically. 104. CIIY—Enter the city or unincorporated area in which the facility is located 490-3a. MONITORING EQUIPMENT IS SERVICED—Check the appropriate box to specify the frequency of monitoring equipment testinglcertification 490-3b Specify Other frequency for monitoring equipment servicing. 490-4 SITE PLAN—Indicate if a site plan/map is submitted with this monitoring plan or if it was submitted previously and is current for the facility Monitoring plans must include a Site Plot Plan/Map showing the tank and piping layouts and the locations where monitoring is performed(i e, location of sensors, probes,line leak detectors,monitoring system control panel,etc) 490-5. IV-I CONTINUOUS ELECTRONIC MONITORING—Indicate if this monitoring method is being used to monitor the tanks 490-6 SECONDARY CONTAINMENT—If IV-1 is checked,check the appropriate box to describe the environment inside the tank secondary containment. 490-7 PANEL MANUFACTURER—If IV-1 is checked,enter the name of the manufacturer of the monitoring system control panel(console) 490-8 MODEL#—If'IV-1 is checked,enter the model number for the monitoring system control panel 490-9 LEAK SENSOR MANUFACTURER—If IV-I is checked,enter the name of the manufacturer of the sensor(s) If additional space is needed,use Section X. 490-10 MODEL#(S)—If IV-1 is checked,enter the model number for each type of sensor installed.If additional space is needed,use Section X 490-11 IV-2 AUTOMATIC TANK GAUGING-Indicate if this method is used for monitoring the UST's. 490-12 PANEL MANUFACTURER—If IV-2 is checked,enter the name of the manufacturer of the monitoring system control panel(console). 490-13 MODEL# If IV-2 is checked,enter the model number for the monitoring system control panel 490-14 IN-TANK PROBE MANUFACTURER—If IV-2 is checked,enter the name of the manufacturer of the probe(s) 490-15 MODEL#(S)—If IV-2 is checked,enter the model number for each type of in-tank probe installed.If additional space is needed,use Section X 490-16 LEAK TEST FREQUENCY—If IV-2 is checked,check the appropriate box to describe the in-tank leak test frequency 490-17. SPECIFY—If 490-16e is checked,enter the frequency of programmed leak tests. 490-18. PROGRAMMED TESTS—If IV-2 is checked,check the appropriate box to describe the tests programmed into the ATG system 490-19 SPECIFY—If 490-18c is checked,enter the frequency of in-tank leak testing, 490-20 IV-3 INVENTORY RECONCILIATION—Check the box if'statistical inventory reconciliation is performed 490-21. IV•4 WEEKLY MANUAL IANK GAUGING Indicate if this method is used to monitor the tanks 490-22 TESTING PERIOD—If'IV-4 is checked,check the appropriate box to describe the MIG testing period 490-23 IV-5 TANK INTEGRITY TESTING:Indicate if this method is used to monitor,the tanks.. 490-24. TEST FREQUENCY—If IV-5 is checked,check the appropriate box to describe the frequency of tank integrity testing 490-25. OTHER If 490-24c is checked,specify other test frequency. 490-26. TV-99 OTHER:Indicate if monitoring of the tanks occurs that is not indicated in any other category 490-27 If IV-99 is checked,enter a brief'description of the other tank monitoring method(s)used(e g.,vadose zone monitoring per 23 CCR§2647,groundwater monitoring per 23CCR§2648) Include the monitoring frequency(e g,Continuous,Weekly). If additional space is needed,use Section X 490-28 V-1 CONTINUOUS MONITORING OF PIPEIPIPING SUMP(S) AND OTHER SECONDARY CONTAINMENT WITH AUDIBLE AND VISUAL ALARMS:Indicate if this is the monitoring method used for the piping. 490-29. SECONDARY CONTAINMENT:If V-1 is checked,Check the appropriate box to describe the environment inside piping secondary containment 490-30. PANEL MANUFACIURER—If V-I is checked,enter the name of the manufacturer of the monitoring system control panel(console) 490-31 MODEL#—If V-1 is checked,enter the model number for the monitoring system control panel 490-32 LEAK SENSOR MANUFACTURER—If V-1 is checked,enter the name of the manufacturer of the sensor(s) 490-33 MODEL#(S)—If V-1 is checked,enter the model number for each type of sensor installed If additional space is needed,use Section X 490-34. PIPING LEAK ALARM T RIGGERS AUTOMATIC PUMP SHUIDOWN —If V-1 is checked,check Yes or No 490-35 FAILURE/DISCONNECTION OF THE MONIIORING SYSTEM IRIGGERS AUTOMATIC PUMP SHUTDOWN-If V-1 is checked,check Yes or No 490-36. V-2 PIPE MECHANICAL LINE LEAK DETECTORS PERFORM 3 GPH LEAK TESTS:Indicate if this monitoring method is used to monitor the pipelines 490-37 MLLD MANUFACTURERS)—If'V-2 is checked,enter the name(s)of the manufacturers)of the mechanical line leak detector(s) If additional space is needed,use Section X 490-38 MODEL#(s)—If V-2 is checked,Enter the model number for each type of mechanical line leak detector installed U additional space is needed,use Section X 490-39 V-3 PIPE ELECTRONIC LINE LEAK DETECTORS:Indicate if this monitoring method is used to monitor the pipelines 490-40 ELLD MANUFACTURER—If'V-3 is checked,Enter the name of the manufacturer of the electronic line leak detector(s) 490-41 MODEL#(S)—If V-3 is checked,enter the model number for each type of electronic line leak detector installed If additional space is needed,use Section X. 490-42. PROGRAMMED LINE INTEGRITY TESTS—If V-3 is checked,check the appropriate box to describe the type of tests programmed into the monitoring system. 490-43. ELLD DETECTION OF A PIPING LEAK ALARM TRIGGERS PUMP SHUTDOWN—If V-1 is checked,check Yes or No 490-44 ELLD DETECTION OF A PIPING LEAK FAILURE/DISCONNECTION TRIGGERS PUMP SHUTDOWN—If V-I is checked,check Yes or No. 490-45 V-4 PIPE INTEGRITY TESTING—Indicate if this monitoring method is used to monitor the pipelines 490-46. TESL FREQUENCY—If'V-4 is checked,check the appropriate box to describe the frequency of pipe integrity testing. 490-47 SPECIFY—If 490-46-99 is checked,enter the frequency of pipe integrity testing.. 490-48. V-5 VISUAL PIPE MONITORING—Indicate if this monitoring method is used to monitor the pipelines. 490-49 If V-5 is checked,check the appropriate box to describe the frequency of visual monitoring 490-50. SUCTION PIPING MEETS EXEMPTION CRITERIA- Indicate if this monitoring method is used to monitor the pipelines. 490-51 NO REGULATED PIPING PER HEALTH AND SAFETY CODE,DIVISION M,CHAPTER 6 7 IS CONNECTED TO THE TANK SYSTEM- Check this box if no piping in the tank system is regulated under the UST law,or there is no piping 490-52 V-99 OTHER—Indicate if another method is used for pipeline monitoring. 490-53 SPECIFY—Enter a brief description of the other line monitoring method(s)used. If additional space is needed,see Section X Be sure to clearly describe monitoring method(s)and frequency This monitoring plan must include a Site Plan showing the general tank and piping layouts and the locations where monitoring is performed(i.e,location of'each sensor,line leak detector,monitoring system control panel,etc). If you already have a diagram(e g,current UST Monitoring Site Plan from a Monitoring System Certification form,Hazardous Materials Business Plan map,etc)that shows all required information,include it with this plan. UPCF UST-D(12/2007)-2/4 www.unidocs org