Laserfiche WebLink
iF <br />t 6 4 ` ie >� F -?Tar i <br />D a 4• k � d i <br />{ <br />RE 4 <br />0 <br />INSTALLATION, INSTRUCTIONS <br />FXV LEAK DETECTORS <br />- --- - - <br />- 5 <br />2VPart No 1-0�F16-57N <br />---- Fx1DV Part No. 116-058-5, FX2DV Part -'No. 11 -0659-5 <br />The following defined terms arc used throughout this literature to bring attention to the Presence of hazards of various risk levels, or to important information concerning thelifeof the product. <br />indicates presence of a hazard which will cause .revere personal injury, death or <br />® .indicates presence of a hazard which will or can cause minor personal: injury, <br />death or substantial property damage if ignored. - <br />substantial property damage if ignored. <br />_ <br />'indicates presence of a hazard which'catt cause severe personal injury, death or. ' - <br />.substantial property damage if ignored. _ _- <br />`'`indicates special instructions 'on installations, opera fion, or maintenance which <br />_. :: are important but not related to personal injury hazards. <br />A - Before installing leak detector, review the application section m`leak deteckor manual #5141 for limitationor restrictions on usage. <br />® This instruction sheet should be kept with. the end user of the lea'k'deteetor for reference. <br />When using 117-182 Sig -Flo Diaphragm Valve, refer to installationi instructions #042-108-1 included with the valve. When using an <br />FXV model leak detector with adapter housing #038 072-5, refer to installation instructions #041-415-1 included with the housing. <br />- FXV Leak Detectors are for use witl .ail UL isted 4 inch Red Jacket models containing a "P" or "AO" prefix; FE Petro UL -Listed <br />.. <br />„ 4 -inch "STP" models-'rokha ini: UL -Listed "4- IiWniodels— 585A-34 and 585A-150. <br />_ p g .., <br />I - Tam erin with the screws seals on this leak detector may <br />inhibit operation and will void warranty. <br />This Red Jacket leak detector is. to be installed into the two-inch <br />cannot be removed, the submersible should be removed <br />threaded tapping on top of the Red Jacket submersible pump. The <br />from the tank and placed in a vise. Remove the functional <br />FXDV models are specially designed for use with diesel fuel. and <br />element assembly next to the pipe plug. The plug should <br />should be used in diesel applications to. -provide the, appropriate <br />then come out readily. if a large pipe wrench is used. <br />operating characteristics. For .proper installation, the following: steps' <br />Replace functional element assembly securely and <br />should be followed -in sequence: - <br />replace the pump in the tank. (See Step 3 before replacing <br />pump). <br />. - DO NOT wire submersible pumps to:. run <br />3. Examine straight bore below two-inch thread for <br />continuously: Red" Jacket line leak"'deteciors will <br />corrosion roughness. If found to be rough,' smooth with <br />not-performleaktests on pumpingsystems that run <br />fine emery paper. <br />continuausiy. ' <br />4. Apply UL -Classified non-toxic pipe thread sealant to the <br />two-inch threads on the detector. Lubricate. O-ring on'the <br />® ALL AIR MUST BE OUT OF THE SYSTEM FOR <br />leak detector. <br />THE LEAK DETECTOR TO WORK PROPERLY. <br />5. Screw the leak detector into the pump. ' Tighten .with a <br />Before installing leak detector in the pump, fill the <br />wrench (top hex is 1-1/4 inch). <br />_system_ with. _product by running the. ._pump and <br />6.- Installation of vent tube and "snap tap connectors. <br />delivering product from each dispenser, (starting <br />For FXIV models . <br />with the farthest from the.pump.and working to the <br />a. Remove .1/4 -inch pipe plug from tank test port, <br />pump) until all -air is removed from system. <br />in the Packer (on 6 -inch Big Flo applications, <br />Certain regulatory bodies require that leak detectors remain in the ` <br />remove the 1/4 -inch pipe plug from the <br />system after the lines have been installed. The lines may be purged of <br />riser/flange assembly). <br />air by back -pressuring the lines with an inert 1 gas, such as helium or <br />b. Apply a UL=classified non-toxic pipe. thread <br />nitrogen, to a pressure of 25 psi (172 k.Pa). This may be done at the <br />sealant to the threads of the 1/4 -inch NPT <br />impact valve under the dispenser. When this pressure has been <br />straight vent tube fitting and install in tank test <br />reached,. the leak detector will be in the open position. By turning on <br />port of the packer. On 6 -inch Big -Flo <br />the pump and gradually bleeding the gas from the line through a valve <br />applications, the 1/4 -inch NPT straight vent <br />at the impact valve of the farthest dispenser, the line may purged of <br />tube fitting may be installed into the riser/flange <br />air <br />assembly. <br />c. Apply a UL -classified non-toxic pipe thread <br />Disconnect power to the submersible pump and "' <br />sealant to the threads of the 1/4 -inch NPT 90 - <br />relieve before Installing or removing <br />degree vent tube fitting Intl install in the leak <br />.pressure <br />petroleum equipment. <br />detector vent opening in the cap of the . leak <br />o <br />1. Disconnect power to putrlp,at the load center. Tag or lock out <br />detector. <br />S . <br />d. Install the vent ftu�ing Into both fittings and <br />the breaker.to avoid the pump, being turned on accidentally. <br />tighten per instructions on.package. <br />2. Remove the two-inchplug 4from the top of the Red Jacket <br />fmmn. 7f the two-inch,nhin, is found,to he so aiellt that it <br />- <br />♦ r 4 4 •{n4 1tlaG <br />+ s 4 d'te 5 ltA4 ?4Mt�'$ia" ....} s. W mq. k s s <br />1 dstl b A4tld H..t t°r tl°•--r'-t <br />a <br />4 k!A A 11 ;1 ."t, «.d°���• tl FM1A R drF <br />! i4 a5 4sm • !tl'.1'�' d <br />