COMPLIANCE INFO_2012-2018 - Laserfiche WebLink

Home Browse Search

4t' i'C� i i to h • 1 b a �Iid i i e *Nye" s'"^�^:y °i Y f"h iAk ONE a Ix T ♦ f i iS / Y { 6 ¢ +�� + ; a fJT _� `7ik �3 R, P b > 9 } w For FX2V models ' a. Remove 1/4 -inch pipe plug from tank test port in the MIM if iiow, is restricted to about 3 gpm (11 1pmor less, , Packer (on 6 -inch Big -Flo applications, remove the with the nozzle open, the teak detector has not 1/4 -inch pipe plug from the nisei/flanpc assembly). opened. Repeat step 8a with increased running b. Apply a UL -classified non-toxic pipe thread sealant to time of pump to insure the purging of all air. All air the 1/4 -inch NPT 45 -degree elbow and install in tank must be. purged from the system or the leak test port of the packer. On 6 -inch Big -Flo applications, detector will restrict flow to about 3 gpm (11 1pm). the 1/4 -inch NPT 45 -degree elbow may be installed '9. Affix the enclosed decals to the dispenser dial glass on grade into the riser/flange assembly.of gasoline upon which the leak detector is being installed. c, Apply UL -classified non toxic pipe thread sealant to Additional decals are available; call customer service at the 1/4 -inch NPT hex nipple and install on 45 degree 1-800-262-7539: h elbow that. is, .in the tank test port (or on 6 inch Big -Flo 10, inspect all threaded joints to assure they are tight and not riser/flange assembly. leaking. d. Apply a UL -classified non-toxic pipe thread sealant to the 1/4 -inch NPT tee and install on the hex nipple to :Test of the Leak Detector accommodate both the vent tube and the snap tap: e. Apply a UL -classified non-toxic pipe thread sealant to U.S. Environmental Protection .Agency (EPA) regulations require the threads of the 1/4 -inch NPT 90 -degree elbow vent annual verification of operation of leak detector. To assure tube fitting.and.insialL.in_the_tee::__:__ .::_. maintenance of leak detection capability, Red Jacket requires that: f. Apply a UL -classified non-toxic pipe thread sealant to operation of thee mechaiucal7eak:detector be verified by testuig upon the threads of the 1/4 -inch NPT straight vent tube start-up and that testing of the'leak detector be performedroutinely at fitting and install.in the leak detector vent opening in least annually. the cap of the leak detector. " -' g. - Install the vent. tubing into both fittings and tighten per_ "lest procedure options for mechanical leak instructions on package, detectors are explained in Red Jacket Engineering h. To install snap tap connectors in FX2V/FX2DV Reports, RJ20 and RJ21. The Red Jacket:Snap Tap models, apply a UL -classified non-toxic pipe thread Connectors allow the l'X2V/FX2D �.Heak detector. to be tested with the. FXV Snap Tap Tester as'aa sealant to the snap tap connectors and install one in the option to the above test methods. See Red Jacket body of the FXV leak .detector and the other, in the tee literature #042-111-1 for test instructions using attached to the hex nipple attached to the 45 -degree. Snap Tap Connectors. elbow installed in the tank test -port of the packer. On 6- 11. The top cover on the Red Jacket leak detector is designed to inch Big -Flo applications, install the two snap tap accommodate sealing wire which can. be used. to connectors -ane in the body of theFXV Teak detector .a discourage tampering or the unauthorized removal of leak and one in the riser/flange assembly. detector. (See Figure 2). i. Attach and crimp loop of the retaining tether around the Snap Tap threads.® j. Replace the caps over the. quick -connect couplings and It should be noted that if the dispensing system (the tighten snugly. solenoid valve and the nozzle) is opened previous to the completion of the line test,. the FXV" Series will detect this opening as a,.leak and restricted flow " DO NOT overtighten. will result. Closing of the nozzle(s) for a period of time adequate to allow completion of the line test ® See technical bulletin #042-111-1 for use of Snap will allow the leak detector to open, Once opened, Tap Connector Assembly. full pump floiy can be provided. 7. Connect power to pump at the load center. 3. :Tear remaining air from system as follows: a. Turn on dispenser that is farthest from the leak detector -but do not open nozzle -Waic4 or ---5 minutes or more. Look for leaks on parts worked on. b. Shutoff the pump and allow it to stand four or five minutes: Then start the pump again and open the FX2V / FX2DV TETFIERED .nozzle farthest from the leak detector. CAP c. Continue to dispense enough gasoline, about 20 to 30 gallons (76 to 114 liters), to pump ALL air from the systhm SNAP TAP Figure 2 NT TUBE