COMPLIANCE INFO_1985-2007 - Laserfiche WebLink

Home Browse Search

Oct 16 07 07:20p Sheila Wallace 9256897921 p.12 2.3.12 The interstitial monitor riser at this facility has been incorporated into the fiberglass turbine enclosure. This riser assembly shall be installed in a 4" by l8", SCH 40 ASTM A-120 steel riser pipe. The cap and adaptor for this riser shall be EBW PIN 90037, equipped with the proper size wire grip. The wire grip shall also be properly sealed with clear GE Silicone. 2.3.13 A single run of secondary piping shall be installed to contain both fuel lines. This piping shall be Environ GeoDuet GDP 45001, 4" phAng. The new bulkhead fittings for the fuel lines shall be Environ DEB -7450 flwdble double entry boot with an Environ SRD-1075 split reducer donut. At the point where both fuel lines exit the soil at the shelter, a Total Containment Termiinadon Assembly, TA4500 and an Environ SRD-1075 split reducer dowA (fuel lines) and Envmm 15-D rubber reducer donut (vent) shall be installed. Please note that the termination assembly is to be installed in such a manner that the nibbcr portion of the assembly is 4 inches clear of the top sock. Also, after the pdmaty piping has been histalled, the conduit system is to be 2.3.14 The pfimary supply and return fuel lines shall be Environ GeoFlex Plus -D piping. The supply line shall) be PGF 2075-D (3I4") and the witun, PGF -2 100-D (1"), double walled flexible piping. The supply piping shall be installed using Environ SPC -0075 swivel couplings and SFA -7575 adapters, and the return piiping shall be installed using Environ SPC -0100 swivel couplings and SFA - 1010 adapters Four (4) standard test boots, (2) STB -0075 and (2) STB -0100, will be required to co te the installation. Please note that the reducer donuts at the building shall be permaneady seaW. 2.3.15 Remove the existing above grade supply and return piping at the exterior of the generator shelticr, including 'Jisolation boot where below grade piping transitions into above grade pipow, Remove the existing gate valve located on the supply line before it eaters the shelter. 2.3.16 Provide a new TC (Total Containment) PIN TA -4500, Termination Assembkv and (1) Environ P/N SRU -10"75, Split reducing donut at location 3/4 Fuel oil supply and 1" fuel oil return stub up from below grade. Termination assembly is to be 'installed in such a manaer that the rubber portion of the assembly has 4" clear of the top rock. It shall be noted that the existing penetrations into the bWkbng shall be reused. 2.3.17 Run new SCH 40-3/," steel fuel oil supply piping up into building penetration. Provide (1) 3/.i' isolation ball valve in vertical before piping mrsts into wall penetration. Ball valve shall be suitable for diesel fuel applications. Provide hot dipped gah=zBd piping supports on either side of valve. Ball valve handle shall be removed and fastened to side of valve with zip tie. 2.3.18 Run new SCH 40-1" Buck steel fuel oil return piping up into exisling building penetiafion. Provide hot dipped pIvanized piping supports where 2.3.19 Any unused penetrafions, as well as worn areas of the exterior of the genwaor sheher shall be sealed and finished to snatch existing. Tbis induudes area of shelter skid where 'isolationvaive was removed. 2.3.20 A single ran of secondary piping shall be installed to contain the vent line. This line shall be Environ GedDuct GDP -45001, 4" The new bulkhead fitft at the twbme enclosure for the vent line shall be Environ DEB -7415 flexible double entry boot. At the point where both the vent lime edits the soil at the fence past, a Total Containment Ternunation Assembly, TA -4500 an FxMron RRD-4015 robber reducer donut shall be installer:. Please note that the