COMPLIANCE INFO_1995-1999 - Laserfiche WebLink

Home Browse Search

VEEDER-ROOT PRESSURIZED LINE LEAK DETECTION SITE PREPARATION ANDHr INSTALLATION INSTRUCTIONS SECTION 1. INTRODUCTION PLLD executes these tests automatically,there is no need for separate annual line leak testing. A. GENERAL There are three versions of the PLLD System available, This manual describes installation procedures for the depending on the brand of pump and the PLLD valve Veeder-Root Pressurized Line Leak Detection (PLLD) hype chosen: System, Form No. 848490-001, -002, or-003. This sys- tem is intended for use in FE Petrol'' and Red Jacket- PLLD System Pumps used with a TLS-350"m UST Monitoring System Pump Brand Valve Type Form No. or a TLS-350RI Environmental & Inventory Manage- ment System. FE Petro None* 848490-001 B. DAMAGE CLAIMS Red Jacket In-line check valve 848490-002 and Tokheim Thoroughly examine all components as soon as received. Red Jacket SwiftCheck-rm 848490-003 "•, NOTE: Insist that the carrier's agent verify the and Tokheim valve(optional) ° inspection and sign the description. *Requires that a Precision Check Valve (FE Petro Immediately notify the delivering carrier of damage or Part Number 400153925) be installed. loss, either in person or by telephone. Mail written con- firmation within 48 hours. Railroads and motor carriers 1. FE Petro Submersible Pump are reluctant to make adjustments for damaged merchan- dise unless inspected and reported promptly. The PLLD System for use with FE Petro submersible Risk of loss, or damage to merchandise remains with the pumps(Form No. 848490-001)contains these items: buyer. It is the buyer's responsibility to file a claim with • 1 -Line Leak Sensor, Part No. 330377-001 the carrier involved. • 6-WARNING Tags,Part No. 329801-001 Immediately advise your Veeder-Root representative, Epoxy Packs, Wire Nuts and Watertight Cord Grip distributor, or the factory so that we may assist you. 1 - Site Preparation and Installation Manual t C. RETURN SHIPPING I I b-A NOTE: See System Requirements, SECTION 1. D., Step 2. All return shipments of Veeder-Root products must be prepaid. If the product is damaged, return it in the origi- 2. Red Jacket and Tokheim Pumps using PLLD In- nal shipping container.Veeder-Root will accept no liabil- line Check Valve ity for damage caused by improper packing. Address the The PLLD System with in-line check valve for use with shipment to Veeder-Root Co., 6th Avenue at Burns Red Jacket and Tokheim pumps (Form No. 848490-002) Crossing,Altoona, Pennsylvania 16602. contains these items: D. SYSTEM REQUIREMENTS 1 -Line Leak Sensor, Part Number 330377-001 • 1 -In-Line Check Valve,Part Number 330368-001 1. Be sure the Veeder-Root TLS-350 or TLS-35OR Sys- . 1 -Pump Port Strainer, Part Number 329861-001 tem has PLLD Interface and PLLD Controller Mod- . 6-WARNING Tags,Part Number 329801-001 ules installed. If these modules are not installed, the . Epoxy Packs, Wire Nuts and Watertight Cord Grip TLS system will not be able to accept inputs from the 0 1 - Site Preparation and Installation Manual PLLD system. 2. If you are installing the PLLD System into a FE 3. Red Jacket and Tokheim Pumps using PLLD Petro'"' Pump, be sure it contains a Precision Check SwiftCheck"m Valve Valve (FE Petro Part No. 400153925)before begin- The PLLD System with the SwiftCheck- valve option ning installation. The PLLD system will not work if for use with Red Jacket and Tokheim pumps (Form No. the Precision Check Valve is not in place. 848490-003)contains these items: • 1 -Line Leak Sensor,Part Number 330377-001 E. SYSTEM DESCRIPTION • 1 -SwiftCheck"A Valve,Part Number 330379-001 The PLLD System performs 3.0 gph leak tests following - 6-WARNING Tags,Part Number 329801-001 each dispense. The PLLD System allows line tests at full • Epoxy Packs, Wire Nuts and Watertight Cord Grip pump pressure for highly accurate 0.1 gph tests. Since - 1 - Site Preparation and Installation Manual 1 L