Laserfiche WebLink
Universal Bulkhead 9stallation <br /> UB0075 <br /> Curved Wall A universal bulkhead is used for custom conduit entries into dispenser <br /> sumps,dispenser pans and sump/risers. Choose location of entry and <br /> Gasket Nut E.S.clasp drill hole using 1-3/4e hole saw only(HS0750).After hole is cut,file edge <br /> to insure absense of burrs or excess plastic. Remove stainless steel <br /> clamp and brass nut from assembly.Prior to inserting fitting,apply bead <br /> of Bostik 920 FS or equivalent around sealing surface. Insert body of <br /> fitting with gasket in tact through hole from outside and assemble so <br /> Washer nut, washer, and stainless steel clamp are on inside of containment <br /> chamber. Install the washer, thread on brass nut and tighten with <br /> wrench(25 to 30foot pounds).Insert conduit through fitting and tighten <br /> Flat Well <br /> stainless steel clamp with torque wrench(CW0030)to 30 inch pound s. <br /> Geaket Nut S.clamp Fill sump with water above penetration to insure bulkhead fitting is <br /> liquid-tight. <br /> b! <br /> / Weans, <br /> UB 1075 <br /> Curved Wall A universal bulkhead is used for custom conduit entries into dispenser <br /> sumps, dispenser pans and sump/risers. Choose location of entry and <br /> Gasket CUtieC Well <br /> S s clamp drillhole using 2-1/2" hole saw onl (HS0250).After hole is cut,file e ge <br /> to insure absense of burrs or excess plastic. Remove stainless steel <br /> �}}II clamp and brass nutfrom assembly.Prior to inserting fitting,apply bead <br /> It���•, of Bostik 920 FS or equivalent around sealing surface. Insert body of <br /> �a 1-0"n <br /> fitting with gasket in tact through hole from outside and assemble so <br /> , <br /> (CS1076) nut and stainless steel clamp are on inside of'containment chamber. <br /> Nut Thread on brass nut and tighten with wrench (25 to 30 foot pounds). <br /> Insert conduit through fitting and tighten stainless steel clamp with <br /> Pat Wall , torque wrench(CW0030)to 30 inch pounds. Fill sump with water above <br /> (3,eskat Flat Well <br /> SS clamp penetration to insure bulkhead fitting is liquid-tight. Note: Use the <br /> provided 3/4" insert(CS 1075) with 3/4"pipe;no insert required for 1 " <br /> pipe <br /> ` <br /> 44 1„<n <br /> CS1076) <br /> Nut <br /> Warranty <br /> Total Containment, Inc.warrants that Sump/Riser underground components, if installed in accordance with <br /> our published Installation Instructions (BF1726) and used per our specifications: <br /> Will meet our published specifications and will be free from material defects in materials and <br /> workmanship for a period of one(1)year following date of original delivery by us, provided the system <br /> is used exclusively for gasoline, jet fuel, av-gas, kerosene, diesel fuel, or motor oil at ambient <br /> underground temperatures; or used for fuel oil not to exceed 150-F. <br /> Our liability under this warranty shall be limited to, at our option, (a) repair of the defective part, (b) delivery <br /> of a replacement part to the point of original delivery, (c) refund of the original purchase price. We shall not <br /> be liable for any labor, removal or installation costs, indirect or consequential damages or other damages in <br /> connection with such parts_THF FOR-EGOING CONSTITUTES OUR-EXCLUSIVE OBLIGATION,AND WE MAKE <br /> NO EXPRESSED OR IMPLIED WARRANTIES, OR ANY WARRANTY OF MERCHANTIBILITY OR FITNESS FOR <br /> ANY PARTICULAR PURPOSE WHATSOEVER, EXCEPT AS STATED ABOVE. <br /> TOTAL <br /> CONTAINMENT <br /> III Mill INC <br /> A130 North Drive • P.O. Box 939 • Oaks, PA 19456 • 610-666-7777 • FAX 610-666-5321 <br /> Designs and specifications are subject to changes without notice. REV0394 <br /> 0TO 1994,U.S.&Worldwide Patents <br />