COMPLIANCE INFO_2001-2004 - Laserfiche WebLink

Home Browse Search

12/02:/2002 15:49 FAX 9163715270 TITAN—PHE WSAC A tank will be fully protected from corrosion. The kit includes materials for covering and protecting the unused tank connections, tank handling hooks, and each of the pipe connections on top of the tank. The PLASTEEL11 kit contains hazardous materials. Read the enclosed material safety data sheets before proceeding to work with PLASTEEL11 kit materials. The standard kit includes the following materials and tools: BOX A 4 each 1 Qt. bottles PLASTEEL11 resin Additional material is supplied when tank configured with containment collars. special fittings, manholes or extension spools. b. Preparation Do not mix the catalyst with the resin until all the pieces you wish to impregnate have bccn fitted in place and the I" strips of matting are laid out next to their corresponding pipe connections. Once the resin and catalyst are mixed, a chemical reaction begins that cannot be reversed. Working time for a mixed batch is about 30 minutes at 70° F. Higher temperatures make it set up more quickly, shortening working time. For example, at 100° F. you will have approximately 15 minutes of working time. The key things to remember are: (1) Be prepared and have all pans prcfitted and in place before mixing the resin. (2) Mix only as much resin as you can use in 30 minutes and mix it thoroughly stir for ai least 1 minute. (3) Work quickly and efficiently. Lower temperatures increase resin set-up time and require additional catalyst. c. Mixing the catalyst Resin and catalyst must be mixed in the proper proportions so that the resin will harden properly. Below is a list of some various size batches you could mix. [a 006 If you're not Sure how fast it will set up, it is better to mix several small batches rather than one big one. d. Application Using the pain L brush provided, DAB the resin mixture into the cloth rather than p Ainting it on. You are trying to completely soak the, matting with resin! not just cover it. e. Pipe and Msers For standard threaded fittings: Apply resin to the but of the pipe and top of tank and pt}sh down the matting circle as shown. Impregnate with resin. Impregnate t strips of matting and wrap like tale around the joint at the base add working upward. Apply any leftover resin to the outside of the join6 when done wrapping. For special bolt -up flanges: Apply generous coating of resin to exposed metal edges of flange and wrap with resin impregnated matting strips. Apply leftover resin to nuts and bolts. it Steel Plugs After fitting fi rglass matting, lift it up and apply mixed resin to the top of the tai surface where the matting will contact. Stick matting over plug Into wet resin and totally impregnate matting with resin. dabbing in frith paint brush as described above. g. Manhole, Extension Spool and Handling Hooks Apply generous coating of resin impregnated matting strips to exposed metal edges and to handling hooks (matting precut). Apply leftover resin to nuts and bolts except on access cover. h. Cleanup Hands and tools may be cleaned with resin emulsifier before the resin has hardened. No solvent will work once the resin has hardened. 1Z I s ;GiESIAi CATALYST) The ELUTRON" tank installation is not complete until all i qt...................1/2 oz. exposed steel surfaces on tank are sealed with the PLASTEEL11 1 pint ..1/4 oz. fiberglass resin. .i/8 oz. For additional assistance or information, call your 1 cup - - - . PLASTEELG ELUTRONm tank factory below: , Authorized PLASTEELa ELUTROW® tank manufacturers INSTALL FWZOW JOOR MFG. K 5 T STEEL METAL PRODUCTS TANG Escondido, CA Twin Falit,10 '&maw. eA off8m (780) 745-0971 (209) 793.2564 (7M 945M (603)5, Fax (7801748.9515 Fax (M) *33.7214 Fmc (770) 932.5871 Fax (903) BOX B I each I Qt. bottle Resin emulsifier or Acetone 4 each 1 Oz. bottles Catalyst 6 each Star Mats 10 each Mat strips 6 each Plug mats 1 - 3 each 4" F1ar pipe plugs 2 each Paint stirring sticks 2 each I -i/2" Paint brushes 3 each Mixing cups I each Sheet 60 grit sandpaper 4 each Hook Mats Additional material is supplied when tank configured with containment collars. special fittings, manholes or extension spools. b. Preparation Do not mix the catalyst with the resin until all the pieces you wish to impregnate have bccn fitted in place and the I" strips of matting are laid out next to their corresponding pipe connections. Once the resin and catalyst are mixed, a chemical reaction begins that cannot be reversed. Working time for a mixed batch is about 30 minutes at 70° F. Higher temperatures make it set up more quickly, shortening working time. For example, at 100° F. you will have approximately 15 minutes of working time. The key things to remember are: (1) Be prepared and have all pans prcfitted and in place before mixing the resin. (2) Mix only as much resin as you can use in 30 minutes and mix it thoroughly stir for ai least 1 minute. (3) Work quickly and efficiently. Lower temperatures increase resin set-up time and require additional catalyst. c. Mixing the catalyst Resin and catalyst must be mixed in the proper proportions so that the resin will harden properly. Below is a list of some various size batches you could mix. [a 006 If you're not Sure how fast it will set up, it is better to mix several small batches rather than one big one. d. Application Using the pain L brush provided, DAB the resin mixture into the cloth rather than p Ainting it on. You are trying to completely soak the, matting with resin! not just cover it. e. Pipe and Msers For standard threaded fittings: Apply resin to the but of the pipe and top of tank and pt}sh down the matting circle as shown. Impregnate with resin. Impregnate t strips of matting and wrap like tale around the joint at the base add working upward. Apply any leftover resin to the outside of the join6 when done wrapping. For special bolt -up flanges: Apply generous coating of resin to exposed metal edges of flange and wrap with resin impregnated matting strips. Apply leftover resin to nuts and bolts. it Steel Plugs After fitting fi rglass matting, lift it up and apply mixed resin to the top of the tai surface where the matting will contact. Stick matting over plug Into wet resin and totally impregnate matting with resin. dabbing in frith paint brush as described above. g. Manhole, Extension Spool and Handling Hooks Apply generous coating of resin impregnated matting strips to exposed metal edges and to handling hooks (matting precut). Apply leftover resin to nuts and bolts except on access cover. h. Cleanup Hands and tools may be cleaned with resin emulsifier before the resin has hardened. No solvent will work once the resin has hardened. 1Z I s ;GiESIAi CATALYST) The ELUTRON" tank installation is not complete until all i qt...................1/2 oz. exposed steel surfaces on tank are sealed with the PLASTEEL11 1 pint ..1/4 oz. fiberglass resin. .i/8 oz. For additional assistance or information, call your 1 cup - - - . PLASTEELG ELUTRONm tank factory below: , Authorized PLASTEELa ELUTROW® tank manufacturers INSTALL FWZOW JOOR MFG. K 5 T STEEL METAL PRODUCTS TANG Escondido, CA Twin Falit,10 '&maw. eA off8m (780) 745-0971 (209) 793.2564 (7M 945M (603)5, Fax (7801748.9515 Fax (M) *33.7214 Fmc (770) 932.5871 Fax (903) 9NDUSTRIAACERO HALLTANK CO. Rzeetow, Poland Out. Ecuador N. Line Roca. AR (501) 945.3211 INOUSTRIAS CORREAGUA JAPAN 87EEL WORKS Fay (6'01) 94S.4477 Panama. Panama Taktw. Japan SHINWON INDUSTRY TANOUES GOMEx TECNOECO ARGENTINA $pint Kam Torreon, Mexieo auenoAft ArMfifts TEMECO CHILE TvG t+anfmgo,Chic Tab,Hungery