COMPLIANCE INFO_1988-2007 - Laserfiche WebLink

Home Browse Search

PFThe INCON TS-LLD is a electronic line leak detector The LINE LEAK TEST light(2)stays on throughout system. It has two components: a control unit(CU) the test. D A N G E R This line leak detector and a leak sensing unit(LSU). The CU is mounted in 4. How to start the manual(0.1 gph)test: Press and may start the pump at the station,and the LSU is installed at the submersible hold the RESET-TEST button down about 5 seconds any time to pressurize fuel pump. One system per pump is used to detect leaks until the LINE LEAKTEST light turns on. lines. Avoid Fire, Explosion 1 TS-LLD from a pressurized fuel line. Requirements: The manual test needs 4 hours hazards, and Electrical shock LINE LEAK DETECTOR The TS-LLD system does three different line leak of quiet-time,before it's started,and about 13 hazards... make sure that all tests,two of these run automatically.The gross 3.0 gph minutes to finish(after it's started).Prevent product dispenser and submersible 2 DISPLAY FUNCTION hourly test,and an intermediate precision 0.2 gph dispensing throughout this time. pump power is turned off / NORMAL: DAYS SINCE MONTHLY LEAK TEST PASSED monthly-compliance test run automatically.The 0.1 NOTE An 80 Alarm error code will appear if a dispense locked out before attempting FLASHING: 1= FAILED ANNUAL(0.1 GPH)LEAK TEST gph annual test must be started manually at the CU. is attempted duringa 0.1 test. DO NOT hold the any service(such as: 3 2= FAILED MONTHLY(0.2 GPH) LEAK TEST p replacing fuel line filters). �y 3= FAILED HOURLY(3.0 GPH) LEAK TEST RESET-TEST button down longer than 4 seconds p g ) Iu� I 29-32=MONTHLY COMPLIANCE WARNING • diperation unless a manual test is desired. 1, 4 33-87= ERROR CODES RESET 88=SYSTEM OK(PRESS TEST TO ACTIVATE) 1. Product dispense—any currently running line leak ®Display Function Codes, & 5 TEST PRESS RESET TO CLEAR ALARM test is aborted,and a functional self-check is done. 1rhe Control Concise Operating PRESS TEST FOR 5 SECONDS TO RUN ANNUAL TEST 2. After every product dispense—the system runsInstructions on the cover. the 3.0 gph hourly test.The 3.0 gph test takes about 0 The 2-digit Display 3 minutes of quiet-time to finish. The LINE LEAK Normal Indications (on-steady): (5)The RESET-TEST button—push Monthly-Compliance Warnings TEST light(2)is on throughout this test. The display is ON steady(not flashing)during ante (DQ NOT hold it down more happen on days:29,30,31 and 32 WHEN a line still Quiet-time is the inactive period between product normal operation,and shows the total number of P p than 4 seconds)to: hasn't passed a 0.2 gph,monthly-compliance test. The dispensing—the dispense lever is down(switch off). days since the last 0.2 gph monthly-compliance test passed...for example: Perform aSelf-Test—if the unit is functioning line is nearly out of compliance with State and Local 3. The system automatically runs the 0.2 gph monthly- normally,it will display an 88(for system okay)when regulations(requiring that a 0.2 gph line leak test pass compliance test after a,3.0 gph test passes unless 00 = zero days(a 0.2 gph test has passed the button is pushed—also see"Diagnostics" each month). within the last 24 hours),up to a 0.2 gph test passed within the last 24 hours(00 • Abort any line leak test that is running—the LINE DAYS DISPLAYED). 28 = twenty eight days LEAK TEST light Q will turn off Indications—a flashing 29, 30,3Wiabled 2 is dis- De endin on conditions at our site the 0.2 h • Clear a Flashing Alarm error code and enable played,and product dispensing i (although P 9 Y 9p Fault Indications (flashing): g a permissive dispense/grace-period is aliowed_,see monthly-compliance test needs 13 minutes to 4 product dispensing—the Alarm error code will hours of quiet-time to finish.The test runs one or The display will rapidly flash Alarm error codes,or reappear if the fault condition remains,and below). more 13 minute test-cycles.Two diagnostic codes are Warning codes—twice persecond—when: • Y g •a leak test fails(a line leak is detected),or when Reset and restart automatic line leak testing—the INCON Recommends—that you push the RESET displayed for two minutes between test-cycles(one leak detected light Q) cannot be reset for 2 seconds,and the other for 6 seconds). •the day count exceeds 28,or when button to clear the Alarm error code,and to permit The control unit displays T rapidly flashing alarm •an error/or fault is detected product dispensing for a maximum of 24 hours,or Automatic Line Leak Testing resumes after a until the next day changes. error codes,diagnostic codes,or days.Normally,it also see"Troubleshooting"formore details. product dispense. .shows the total number of days since the last I Before da 32 is flashed and before you o out of monthly-compliance test passed.The days advance a Q The LINE LEAK TEST light is on during any See"Normal Operation#4),about the requirements compliance,INCON Recommends g that you day for every 24 hours that a monthly test has not leak test.It turns off after a test finishes,or when a• of,and how to start a manual 0.1 h test. • finished. It counts up to 28 days before aMonthly- dispense occurs,which causes the test to abort and ( gph) push the RESET-TEST button,simulate a dispense, to Compliance Warning is flashed(starting on day 29) restart again(see Normal Operation#1),or when the and prevent dispensing so the test has time 0. ...see`Troubleshooting"for more details.It may take RESET-TEST button is pressed. • - : • ' - - _ finish. Alternatively,you can start an manual, gph .days before the quiet-time is long enough to let the -- annual leak test if sufficient quiet-time has accumu- Q The LINE LEAK DETECTED light Start an error-log and record all: Flashing alarm error lated. See"Normal Operation#4)",about the test finish(especially in busy 24-hour stations). flashes on and off continuous) when a line leak test Month) tests also start when the Y codes,the TS-LLD#(Product Line#) and the Date and requirements of,and how to start a manual test. Y Y fails. It keeps flashing until another test of equal or Time that the error occurred.Have this data on hand system is first powered up,and whenever the display greaterprecision passes. before calling for help,or service. advances to the next day. Continued...