Laserfiche WebLink
ITEM <br />1 <br />2 <br />3 <br />4 <br />5 <br />6 <br />7 <br />8 <br />9 <br />10 <br />11 <br />12 <br />13 <br />14 <br />15 <br />16 <br />17 <br />18 <br />19 <br />20 <br />Executive Order VR -101-A, Exhibit 3, Page 7 <br />Figure 3E <br />Phil-Tite 85000 and 85000 -MS Product Spill Container and Drain Valve Assembly <br />INSTALLATION INSTRUCTIONS: <br />Cut and fit tank riser to terminate approximately 20" below finish grade. Use coupler and <br />factory nipple to finish riser height to terminate 13-3/4" below finish grade. Next, measure <br />and cut drop tube on a bias (minimum 2" from tank bottom - maximum G" from bottom) <br />and install tank bottom protector if needed. Install drop tube with proper seals. Install <br />Product bucket and torque to approximately 50 ft. lbs. (using Phil-Tite Enterprises' tool <br />kit - part #T-7043). <br />Next install swivel adaptor using Phil-Tite Enterprises' tool kit - part #T-7043 <br />(available in our catalog) and torque to approximately 30 ft. lbs. Tighten setscrews to <br />secure swivel. <br />The use of any unapproved tools, or over tightening bucket or swivel, will void any <br />and all applied warranties. <br />MAINTENANCE INSTRUCTIONS: <br />Semi -Annually: Clean entire bucket and remove Drain Valve Assembly. Inspect all seals <br />and replace components as needed. Upon completion, make sure bucket, valve, handle, <br />and filter are properly aligned and adjusted. <br />PART No <br />DESCRIPTION <br />REQ'D <br />85010 <br />SLEEVE <br />1 <br />85019 <br />FLANGE NUT <br />1 <br />85018 <br />COMPRESSION RING <br />1 <br />85065 <br />BUCKET <br />1 <br />85035 <br />RISER TUBE O—RING (OUTER) & <br />2 <br />SHUT OFF COLLAR O—RING (UPPER) <br />85039 <br />RISER TUBE 0—RING (INNER) <br />1 <br />85020 <br />RISER TUBE <br />1 <br />85036—N <br />BUCKET O—RING <br />1 <br />85038-1 <br />SHUT OFF COLLAR 0—RING (LOWER) <br />1 <br />85021 <br />SHUT OFF COLLAR <br />1 <br />85032 <br />BELLOW & SCREEN <br />1 <br />UF8005 <br />FOAM FILTER <br />1 <br />85031 <br />BELLOW & SCREEN RETAINING RING <br />1 <br />85050 <br />CLAMP (LOWER) <br />1 <br />85040 <br />CLAMP (UPPER) <br />1 <br />PP-1005—TB <br />BUCKET INSERT <br />1 <br />SC-1513V—N <br />LID O—RING <br />1 <br />85011 <br />CAST LID <br />1 <br />85023 <br />BAIL HANDLE <br />1 <br />85029 <br />EXTENSION SKIRT (OPTIONAL) <br />1 <br />SEL 7LCESSOB16' SECBDN <br />OT 5 "T w <br />MODEL 85000 <br />Ju ASSWKY) <br />EYfLNS10N WI <br />t,Tk*Ay ON NODCL 85000) <br />,JWLWM DN MM 85000-S) <br />Component Warranty Tag. Placed on outside <br />of spill container, near top, just below upper lip. <br />