Laserfiche WebLink
Easy Installation! The 3" inlet the 99 LD -3000 allows the leak detector to installed in the discharge port of <br />3 - 5 HP submersible pumps. The discharge of the 99 LD -3000 is 3" male thread; Height - 16.25 inches. Width - 7.86 <br />inches. Weight -29 pounds; Can be installed by one person. Now with easy access to check valve for field replacement. <br />The 99 LD -3000 is available with flange fittings instead of threads as Part # 99 LD-30001FL. <br />Integrated In -Line hec Valve/PressureRelief: Allows the leak detector to compensate for a defective <br />submersible pump pressure relief or check valves that allow drain -back into tanks. The integrated pressure relief valve <br />of the 99 LD -3000 will hold 30 PSI in the line by itself. <br />One Way Poppet Flow Path' Isolates pump turbulence from line leak detection at pump start-up. The hardened <br />stainless steel poppet does not dimensionally change due to thermal conditions encountered during station operation <br />(precision metering change is insignificant down to -20 degrees F). <br />Reverse Ratio Piston / Poppet Combination: The leak detector has a smaller diameter piston area than <br />the poppet it is attached to. This allows the leak detector to stay in the fast fill position (3 GPM) to a higher pressure <br />while compressing vapor pockets and stretching flexible line faster, resulting in less time to full flow. <br />Smaller Volume / Faster Response Piston Size: Results in one-fourth the volume of fuel to replace <br />when in leak search and one-fourth the volume to return to the line when pump is turned off. This results in achieving <br />faster full flow to dispensers and faster resets to detect leaks. <br />Fuels: Gasoline, 100% methanol*, 100% ethanol*, up to 15% MTBE <br />• Any combination of the above <br />#1 or#2 diesel, kerosene, Jet A* or JP -4*, AV Gas* <br />and Biodiesel* (all blends). <br />* When used with Blodiesel, any alcohol fuel concentration above 20%,JetA, JP -4, or <br />AV Gas, order part # LD3-SSVS for stainless steel fittings and stainless steel vent <br />tubing. For chemical applications other than those listed above, contact factory. <br />• Rigid pipe up to 406 gal., 1171 ft. of 3" id. <br />• Flexible pipe up to 96 gal., 260 ft. of 3" id. <br />Combination of Rigid and Flexible pipe up to 502 gal., 1431 ft. of 3" id. <br />Construction: Forged steel body; Steel alloy; Forged steel threads. <br />Cylinder Assembly: Anodized 6061-T6 Aluminum <br />Internal Parts: Anodized 2011-T3 Aluminum, 6061-T6 Aluminum; <br />Acetron GP; CDSM 1026 and DOM 1026 steel; <br />17-4 stainless steel <br />seals: Low drag, stainless steel spring energized teflon seals <br />O Rings: U. L. Approved V9702-Viton Type B Fluorocarbon <br />Metering Pin and Poppet: 17-4 stainless steel <br />Check valve: Acetron GP, Viton F Seal <br />Pressure Relief: Stainless Steel, 29 PSI pressure relief. This pressure is in <br />addition to the pump pressure relief. <br />Inlet: 3" male Outlet: 3" male <br />7.85 <br />S . 56 --`j <br />Pc.».2a <br />PORT <br />RWPF-s ? <br />i <br />8.7s <br />TeST <br />PORT <br />3' MALE <br />c� ssus <br />t 18 t�7 <br />TYP iCAL <br />3' MALE NPT <br />• Certified to handle 12+ feet of head pressure. <br />• Exceeds EPA specifications for 3 GPH @ 10 PSI hourly test. <br />• Vent line must be unobstructed, leak tight and connected to headspace of tank, not to be subjected <br />to pressure or vacuum. <br />• Combination line check/pressure relief prevents drainage into the tank. <br />Vaporless Manufacturing, Inc. Toll Free: 1-800-367-0185 <br />VM I, 8700 East Long Mesa Drive Phone: (928) 775-5191 <br />Prescott Valley, Arizona 86314 Fax: (928) 775-5309 <br />02108 Web Site: www.vaporiess.co • Email: vmi@vaporiess.co <br />