Laserfiche WebLink
E <br />I <br />11 <br />G' <br />0 <br />n <br />2.02 PROPERTIES FOR TEXTURED (BOTH SIDES) LINEAR LOW DENSITY <br />POLYETHYLENE (LLDPE) GEOMEMBRANE <br />A. Manufacturing. <br />1. Meeting the latest requirements of GRI GM17 except where modified by this <br />specification. <br />Test <br />Do not exceed a combined maximum total of 1 percent by weight of additives <br />Requirements <br />Test <br />Designation <br />MQC Test Frequency <br />Requirements <br />Resin Melt Flow Index <br />ASTM D1238 <br />1 per resin batch <br />Less than 1.0g /10 min. <br />Condition E <br />(i.e. Batch, Rail Car) <br />any roll, not less than 58 mils. <br />Resin Specific Gravity <br />ASTM D1505 or <br />1 per resin batch <br />>0.915 g/cm3 (resin only) <br />must not bloom��to the surface over time or inhibit welding. <br />D792 Method B <br />(i.e. Batch, Rail Car) <br />(Finished Product: 0.92 g/ cm3) <br />2.02 PROPERTIES FOR TEXTURED (BOTH SIDES) LINEAR LOW DENSITY <br />POLYETHYLENE (LLDPE) GEOMEMBRANE <br />A. Manufacturing. <br />1. Meeting the latest requirements of GRI GM17 except where modified by this <br />specification. <br />G' <br />fl <br />L <br />Test <br />2. <br />Do not exceed a combined maximum total of 1 percent by weight of additives <br />Requirements <br />Sheet Thickness <br />other than carbon black or pigment. Identify percentage of processing aids, <br />10 per roll <br />60 mils minus 10% for any measurement <br />antioxidants, and other additives other than carbon black. <br />3. <br />Do not exceed 3.5 percent by weight of finished geomembrane for total <br />combined processing aids, antioxidants, carbon black, and other additives. <br />any roll, not less than 58 mils. <br />4. <br />All additives for UV protection, thermal stability, color, or processing agents <br />Every second roll <br />Minimum 20 mils average measurement <br />must not bloom��to the surface over time or inhibit welding. <br />S. <br />Use materials produced in the United States or Canada. <br />6. <br />Provide finished product free from blemishes, holes, pinholes, bubbles, <br />requirements <br />blisters, excessive gels, undispersed resins, and/or carbon black, contamination <br />by foreign matter and nicks or cuts on edges. <br />' <br />7. <br />Roll manufactured sheets for shipment. Provide roll identification labels <br />indicating nominal thickness, length, width, manufacturer, and plant location. <br />B. Meeting the following requirements: <br />G' <br />fl <br />L <br />Test <br />Test <br />Designation <br />MQC Test <br />Frequency <br />Requirements <br />Sheet Thickness <br />ASTM D5994 <br />10 per roll <br />60 mils minus 10% for any measurement <br />and the average of all measurements for <br />any roll, not less than 58 mils. <br />Asperity Height (1) <br />GRI — GM12 <br />Every second roll <br />Minimum 20 mils average measurement <br />(1),(2) <br />and as needed to meet shear strength <br />requirements <br />SHAW ENV/RoNmENTAL, /NC. <br />San Joaquin County — Extension of Cap Corral Hollow Sanitary Landfill — CH—Closure Cap Ext Proi jechnical Specs -4-19-12 Rev I .DocRev. 0, 04/05/2012 <br />LLDPE Geomembrane <br />11 rMIFA A <br />