|
REVISIONS BY
<br /> DIVISION 7-SEALANTS AND CAULKING DIVISION 9 - FINISHES
<br /> I. PROVIDE NON-SAG SEALANT COMPLYING WITH REQUIREMENTS OF FEDERAL SPECIFICATIONS DOOR BUTTS PBB, HANGER, STANLEY G.- MIRRORS : LAMINATED ARCHITECTURAL GLASS, I / 4 INCH THICK, METAL SUPPORT SYSTEM (WALL STUDS)
<br /> TTS-1 543 OR FS TT-5-230 TYPE"11", CLASS"A" PROVIDE ACOUSTICAL SEALANT WHICH CONFORMING TO ANSI Z97. 1 , AND AS MANUFACTURED BY DOWNEY GLASS I. PROVIDE CHANNEL-SHAPED ROLL FORMED SHEET STEEL MEMBERS CONFORMING WITH
<br /> SHALL BE NON-HARDENING, NON-DRYING SYNTHETIC RUBBER SEALING COMPOUND WITH MIN.- LOCK5ET5 (A SERIES, LEVERS) SCHLAGE OR APPROVED EQUAL. ASTM CG40, HOT DIPPED FINISH WHERE EXPOSED TO MOISTURE NOT LESS THAN 20 GAUGE.
<br /> IMUM 90%SOLIDS. USE AT ALL INTERIOR JOINTS AT INNER SECTIONS BETWEEN PLANES. CLOSERS VON DUPRIN, LCN PROVIDE I G GAUGE AT DOOR JAMBS.
<br /> AROUND DOOR AND WINDOW FRAMES PRIMER SHALL BE MADE OR RECOMMENDED BY SEALANT
<br /> MANUFACTURER FOR THE SPECIFIC CONDITIONS AND SUBSTRATES. STOPS TRIMCO, IVES, 7.- ALL GLAZING SHALL BE DONE BV SKILLED GLAZERS AND IN 2. PROVIDE COLD, ROLLED STEEL CHANNELS NOT LESS THAN I G GAUGE.
<br /> 2. PROVIDE BACKING MATERIAL BY DOW"ETHAFOAM"OR APPROVED EQUAL. APPLY SEALANT GLYNN-JOHNSON ACCORDANCE WITH THE BEST STANDARD PRACTICE. GLASS SHALL BE 3. PROVIDE ROLL HAT-SHAPED CHANNELS MINIMUM 25 GAUGE, 7/8" DEEP WITH 1/2" HEMMED
<br /> OVER BACKING TO UNIFORM THICKNESS IN CONTINUOUS BEADS FILLING ALL JOINTS AND OVERHEAD HOLD OPENS CORRIN-RUSSWIN SET TIGHT AND TRUE IN CLEAN, DRY SASH. PROVIDE CLIPS, BLOCKS, AND EDGES. HOT DIPPED FINISH WHERE NOTED.
<br /> 4. PROVIDE TIE WIRES OF GALVANIZED ANNEALED WIRES NOT LESS THAN 16 GAUGE.
<br /> VOIDS SOLID. SUPERFICIAL POINTING WITH THE SKIM BEAD WILL NOT BE ACCEPTED. PUSH/PULLS TRIMCO, IVES,
<br /> SHIMS AS REQUIRED. 5. PROVIDE GALVANIZED HANGERS OF STEEL WIRE IN ACCORDANCE WITH ASTM C754.
<br /> 3. ALL SURFACES SHALL BE ADEQUATELY CLEANED AND PREPARED IN ACCORDANCE WITH GLYNN-JOHNSON
<br /> MANUFACTURER'S WRITTEN INSTRUCTIONS PRIOR TO INSTALLATION. KICKPLATES TRIMCO, IVES G. PROVIDE JACK STUDS BETWEEN BOTTOM TRACK AND WINDOW AND/OR RELIEF SILLS BETWEEN
<br /> THE CONTRACTOR SHALL BE RESPONSIBLE FOR PROTECTING EXPOSED LINTELS AND HEADERS IN TOP TRACKS.
<br /> 4. KITCHEN EQUIPMENT CONTRACTOR SHALL PROVIDE AND CAULK AROUND ALL EQUIPMENT TO DOOR BOTTOMS, THRESHOLDS, SEALS PEMKO, TRIMCO, ZERO SURFACES FROM DAMAGE AND FINAL CLEANING OF GLAZING. 7. PROVIDE BLOCKING AND FRAMING FOR ALL WALL MOUNTED FINISH HARDWARE AND EQUIP-
<br /> CREATE A CLEAN, TIGHT AND WATER PROOF SEAL. EXIT DEVICES VON DUPRIN MENT, INCLUDING DOOR STOPS.
<br /> FLUSH BOLTS TRIMCO 8. PROVIDE DOUBLE BEAD TO BUTYL SEALANT AT FLOOR TRACKS. APPLY DOUBLE BEAD TO v M
<br /> PAINTING CEILING TRACK AND TO STUDS ABUTTING OTHER CONSTRUCTION. Z O �
<br /> FLOOR CLOSERS AND PIVOTS DORMA _ F- z
<br /> COORDINATORS TRIMCO I . PROVIDE PAINT FINISHES FOR BUILDING AND OTHER SURFACES AS SCHEDULED ON DRAWINGS 9. PROVIDE CHANNEL SHAPED BLOCKING SUPPORT OR GALVANIZED STRIP SUPPORT OF WALL-HUNG ., L) , o
<br /> ENTRANCES AND STOREFRONTS CABINETS, EQUIPMENT, FIXTURES AND ACCESSORIES OF NOT LESS THAN 22 GA. MATERIAL. PRO- z 11 1
<br /> STRIKES TRIMCO VIDE SUPPORT IN WALL OR PARTITION FRAMING SYSTEM WHEREVER WALL HUNG CABINETS AND aD Lu
<br /> NO PAINT FINISH IS REQUIRED ON ITEMS HAVING COMPLETE FACTORY FINISH, EQUIPMENT ARE INDICATED ON DRAWINGS. AND WHERE REQUIRED FOR MOUNTING OF MISCEL- P Z c
<br /> SILENCER GLYNN-JOHNSON V
<br /> EXCEPT AS MAY BE SPECIFIED HEREINAFTER; PUTTY AND/OR SEALANT AT ALUMINUM WIN- ANEOUS ITEMS REQUIRING BACKING. O J J
<br /> I .- ENTRANCES AND STOREFRONTS : PROVIDE ALL LABOR, MATERIALS, DOWS; NON-FERROUS METAL UNLESS SPECIFICALLY MENTIONED IN THE PAINTING SCHEDULE; Z
<br /> 10.SET FLOOR TRACKS IN ACCURATE LOCATIONS AND SECURELY ANCHOR IN ACCORDANCE WITH V
<br /> EQUIPMENT, AND ENGINEERING REQUIRED FOR THE COMPLETE STAINLESS STEEL; INTERIOR OR EXTERIOR OF EXISTING BUILDING, EXCEPT WHERE ALTERATIONS ASTM STANDARDS. ERECT STUDS ON I G"OR 24" (AS INDICATED)CENTERS AND SECURE TO 0 C V
<br /> INSTALLATION OF ENTRANCE DOORS AND STOREFRONT FRAME SYSTEMS 12.- FINISHES : ALL HARDWARE FINISHES TO BE U52GD, "SATIN CROME". OCCUR OR WHERE SCHEDULED. PAINT GRILLES AND DIFFUSERS. NO PAINTING IS REQUIRED TRACK. INSTALL HEAD TRACK IN ACCORDANCE WITH DETAILS. INSTALL BLOCKING, BRACING, �' Z U)
<br /> WITH INTEGRAL AIR AND VAPOR BARRIERS, INCLUDING CLIPS ANCHORS, PROVIDE MATCHING FINISHES FOR HARDWARE UNITS AT EACH DOOR, TO FOR INSULATING PIPING, EXCEPT WHERE EXPOSED IN FINISH, NON-MECHANICAL ROOM SPACES. AND ANCHOR STRIPS; LEAVE READY TO RECEIVE FINISH MATERIALS. 0 o W O
<br /> cc 0
<br /> VINYL GLAZING BEADS, AND OTHER ACCESSORIES. PROVIDE ALL ENTRY THE GREATEST EXTENT POSSIBLE. 2. PROTECT WORK OF OTHER TRADES FROM DAMAGE AND DEFACEMENT CAUSED BY THIS WORK. 1 1.ERECT ALL COMPONENTS FOR CEILING AND SOFFIT FRAMING IN ACCURATE LOCATIONS AS
<br /> INDICATED, TRUE TO LINE, LEVEL AND PLUMB, AND IN ACCORDANCE WITH APPLICABLE ASTM2 W m
<br /> DOOR HARDWARE, INCLUDING THRESHOLDS AND CLOSERS. DESIGN AND REPAIR ANY DAMAGE CAUSED BY THE WORK OF THIS SECTION. REMOVE ELECTRICAL OUTLET STANDARDS AS REFERENCED ABOVE, USING A LASER LEVEL. ADJUST SUPPORTS, SPANS li
<br /> SIZE COMPONENTS IN ACCORDANCE WITH CBC CODE EXPOSURE "B" AND 13.- GROUPS : IN GENERAL THE GROUPS SHALL BE AS FOLLOWS: AND SWITCH PLATES, MECHANICAL DIFFUSERS, GRILLES, ESCUTCHEONS, REGISTERS, SURFACE OR OTHERWISE FOR INSTALLATION WITHIN SPECIFIED TOLERANCES. J 0 '' 1
<br /> WIND SPEED OF 70 MPH AND IN ACCORDANCE WITH ANSI/ASTM E330. LIMIT HARDWARE, FITTINGS, AND FASTENINGS PRIOR TO COMMENCING THE WORK. STORE, CLEAN, 12.PROVIDE KICK BRACING IN ACCORDANCE WITH INDUSTRY STANDARDS FOR WALL STUDS, CEIL- co g a 11J
<br /> AND REPLACE UPON COMPLETION. ING MEMBERS, DRAFT OR SMOKE STOPS AND CURTAIN WALLS.
<br /> MULLION DEFLECTION TO U360 WITH FULL RECOVERY OF GLAZING A.- ENTRY/EXIT EXTERIOR STOREFRONT DOOR: 0 Z k- C)
<br /> ATERIALS. DOORS SHALL COMPLY WITH ADA REQUIREMENTS. 3. PAINT CONTRACTOR SHALL NOTIFY THE GENERAL CONTRACTOR IF ANY SURFACE TO BE PORTLAND CEMENT PLASTER w
<br /> I I / 2 PAIR HINGES ( 3 PAIR HINGES FOR PAIR OF DOORS) PAINTED OR STAINED 15 FOUND TO BE UNSUITABLE TO PRODUCE PROPER FINISH. APPLY NO %
<br /> CYLINDER LOCK FINISH MATERIAL UNTIL THE UNSUITABLE SURFACES HAVE BEEN MADE SATISFACTORY.
<br /> 2.- WINDOW WALL AND DOOR SYSTEMS SHALL BE AS MANUFACTURED BY I .- THREE-COAT PORTLAND CEMENT PLASTER SYSTEM WITH INTEGRAL C
<br /> KAWNNER CO. FOR I INCH DUO GLAZING. FRAMING MEMBER PROFILE EXIT DEVICE 4. FINISH WORK SHALL BE UNIFORM, OF APPROVED COLOR, SMOOTH AND FREE FROM RUNS. COLOR ACRYLIC FINISH COAT SHALL BE IN ACCORDANCE WITH ASTM C926 V r
<br /> CLOSER `
<br /> SHALL BE 4 INCH BACK SPAM UNLESS NOTED OTHERWISE ON THE MAKE ENDS OF PAINT ADJOINING OTHER MATERIALS OR COLORS SHARP AND CLEAN. WHERE AND CBC SECTION 25 10. J
<br /> . DO NOT APPLY PLASTER WHEN SUBSTRATE OR W
<br /> O
<br /> DRAWINGS. DOORS SHALL BDOOR STOP ( FLOOR OR WALL )E " WIDE STILE" , 4 AND I / 2 INCH VERTICAL THRESHOLD HIGH GLOSS ENAMEL IS USED, LIGHTLY SAND UNDERCOAT TO OBTAIN A SMOOTH FINISH COAT. AMBIENT AIR TEMPERATURE IS LESS THAN 50 DEGREES F NOT MORE THAN
<br /> FACE DIMENSION BY 2 INCHES DEEP, WELDED INTERSECTIONS, 12 INCH 90 DEGREES F. IF FREEZING IS EXPECTED WITHIN THE NEXT 12 HOURS,
<br /> BOTTOM RAIL. FABRICATE FROM GOG3 T5 ALLOY. STRUCTURED MEMBERS KICK PLATES 5. PROVIDE ALL NEWLY PAINTED SURFACES WITH (I) COAT TINTED PRIMER AND A MINIMUM OF (2) COATS WEATHERSTRIPPING FINAL COLOR COAT, (UNLESS OTHERWISE RECOMMENDED BY MANUFACTURER'S SPECIFICATIONS) DO NOT APPLY PLASTER. MAINTAIN MINIMUM AMBIENT TEMPERATURE OF
<br /> 8 W
<br /> SERVING AS STRUCTURAL SUPPORT SHALL BE CAPABLE OF SPANNING �L Q
<br /> SILENCER ( METAL FRAMES ) TO PROVIDE A SOLID, UNIFORM AND DURABLE FINISH. ALLOW PROPER DRYING TIME BETWEEN COATS. 50 DEGREES F DURING AND AFTER INSTALLATION. PROTECT PLASTER
<br /> FEET WITHOUT INTERMEDIATE SUPPORTS. COLOR : BRONZE OR AS FROM UNEVEN AND EXCESSIVE EVAPORATION DURING ANY WEATHER
<br /> SELECTED BY THE ARCHITECT FROM MANUFACTURES STANDARD ( ASTRAGAL FLUSH BOLTS FOR PAIR OF DOORS ) G. DELIVER ALL PAINT TO J055ITE IN UNOPENED CONTAINERS BEARING THE MANUFACTURER'S CONDITIONS.
<br /> COLORS. B.- EXIT EXTERIOR DOOR: LABEL, AND SHOWING PAINT TYPE, SHEEN AND COLOR.
<br /> 1 I / 2 PAIR HINGES ( 3 PAIR HINGES FOR PAIR OF DOORS) 7. PAINT TYPES USED SHALL BE THOSE SPECIFICALLY RECOMMENDED BY THE MANUFACTURER 2.- PLASTER MATERIALS
<br /> 3.- WINDOW WALL AND DOOR SYSTEMS SHALL BE SET IN THE PROPER CYLINDER LOCK FOR THE MATERIAL TO WHICH THEY WILL BE APPLIED. PAINTING CONTRACTOR SHALL FOL-
<br /> LOCATIONS AND SHALL BE SQUARE, PLUMB, LEVEL, AND JOINED TO EACH EXIT DEVICE LOW MANUFACTURER'S INSTRUCTIONS FOR PROPER APPLICATION OF THE PAINT. a.- CEMENT: ASTM C 150, NORMAL-TYPE 1-II, LOW ALKALI, GRAY COLOR,
<br /> OTHER AND INSTALLED IN STRICT ACCORDANCE WITH MANUFACTURER'S PORTLAND CEMENT.
<br /> CLOSER 8. ALL SURFACES TO BE PAINTED SHALL BE THOROUGHLY CLEANED, AND PREPARED FOR
<br /> INSTRUCTIONS.INSULATE ALL ALUMINUM WORK FROM CONTACT WITH DOOR STOP ( FLOOR OR WALL ) PAINTING PRIOR TO APPLICATION OF PAINT. PROVIDE VENTILATORS AS REQUIRED TO PREVENT b.- AGGREGATE : IN ACCORDANCE WITH ANSI/ASTM C897, GRADING
<br /> PLASTER AND / OR CONCRETE. ALL POSSIBLE SOURCES OF AIR OR WATER THRESHOLD BUILD-UP OF FUMES. REQUIREMENTS.
<br /> LEAKS SHALL BE THOROUGHLY SEALED. THE USE OF ALL CAULKING AND KICK PLATES c.- WATER : CLEAN, FRESH, POTABLE AND FREE OF MINERAL OR
<br /> ORGANIC MATTER.
<br /> SEALING COMPOUNDS SHALL BE IN STRICT ACCORDANCE WITH THE 9. SANDPAPER ALL NEW WOOD TO SMOOTH AND EVEN SURFACE AND DUST OFF. AFTER PRIM-
<br /> MANUFACTURER'S PRINTED RECOMMENDATIONS. WEATHERSTRIPPING ING COAT HAS BEEN APPLIED, THOROUGHLY FILL ALL NAIL HOLES AND OTHER SURFACE IM-
<br /> SILENCER ( METAL FRAMES ) PERFECTIONS WITH PUTTY TINTED WITH PRIMER OR STAIN TO MATCH WOOD COLOR. SAND d.- ACRYLIC FINISH COAT: VAPOR PERMEABLE, 100 PERCENT ACRYLIC
<br /> ASTRAGAL * FLUSH BOLTS FOR PAIR OF DOORS ) ALL WOODWORK BETWEEN COATS TO A SMOOTH SURFACE. POLYMER FINISH COAT WITH CRUSHED MINERAL AGGREGATES. COLOR
<br /> 4.- AL DOORS AND FRAME SHALL BE ACCURATELY MORTISED, CUT OUT ( AND TEXTURE AS SELECTED BY ARCHITECT.
<br /> AND REINFORCED FOR HARDWARE AS SPECIFIED IN FINISH HARDWARE. I O.PRIME ALL SURFACES WHICH RECEIVE PAINT PRIOR TO APPLICATION OF FINAL FINISH,
<br /> C.- INTERIOR DOORS FOR RESTROOMS IN ACCORDANCE WITH MANUFACTURER'S SPECIFICATIONS.
<br /> I I / 2 PAIR HINGES 3.- LATH AND LATH ACCESSORIES
<br /> 5.- ALL GLAZING SHALL BE DONE BY SKILLED GLAZERS AND IN 1 1 .BACK PRIME ALL EXTERIOR AND INTERIOR WOOD AND TRIM PRIOR TO INSTALLATION. THOR-
<br /> ACCORDANCE WITH THE BEST STANDARD PRACTICE. GLASS SHALL BE PUSH/ PULL PLATES OUGHLY CLEAN SURFACES AND APPLY NO FINISH UNLESS SURFACES ARE DRY AND READY a.- METAL LATH: SELF FURRED GROOVED EXPANDED METAL DIAMOND
<br /> SET TIGHT AND TRUE IN CLEAN, DRY SASH. PROVIDE CLIPS, BLOCKS, AND CLOSER FOR APPLICATION. SANDPAPER SURFACES OF TRIM SMOOTH AND WIPE CLEAN. AFTER STAIN MESH, GALVANIZED FINISH AS MANUFACTURED BY CLARKDIETRICH r
<br /> SHIMS AS REQUIRED. DOOR STOP ( FLOOR OR WALL ) COAT HAS BEEN APPLIED, FILL CRACKS AND HOLES WITH PLASTIC WOOD OR PUTTY. IF STAIN BUILDING SYSTEMS. v J
<br /> KICK PLATES HAS BEEN USED, TINT CRACK FILLER TO MATCH; PRIME BACKS OF TRIM. PRIME BARE WOOD z
<br /> G.- THE CONTRACTOR SHALL BE RESPONSIBLE FOR PROTECTING SILENCER ( METAL FRAMES ) SCHEDULED TO RECEIVE PAINT FINISH; FINISH NAIL HOLES, CRACKS, AND OTHER IMPERFECT- b.- CASING BEADS : FORMED STEEL, MINIMUM 2G GAUGE THICK; OF O
<br /> EXPOSED SURFACES FROM DAMAGE AND FINAL CLEARING OF ALUMINUM
<br /> IONS WITH PUTTY AND SAND SMOOTH. LONGEST POSSIBLE LENGTH; SIZED AND PROFILED TO SUIT APPLICATION;
<br /> GALVANIZED FINISH; No.- 66C5ING BEAD.
<br /> AND GLAZING. NOTE : PROVIDE CLOSERS AND SMOKE SEALS AT ALL RATED DOORS. 1 2.AT COMPLETION, TOUCH-UP AND RESTORE FINISH WHERE DAMAGED AND LEAVE ALL SUR- c.-SOFFIT VENT : 6 INCH REVAL WIDTH, VENTED, 6063 - T5 EXTRUDED
<br /> FACES IN GOOD AND CLEAN CONDITION. PROVIDE FOR ONE TOUCH-UP TRIP FOR ENTIRE PROJECT
<br /> 14.- INSTRUCT OWNER'S PERSONNEL IN PROPER ADJUSTMENT AND PRIOR TO OPENING. ALUMINUM WITH CLEAR ALUMINUM FINISH, MODEL No.- PC5-75-V-G00 AS
<br /> MAINTENANCE OF HARDWARE FINISHES. 13.OTHER PAINT MANUFACTURER'S MAY NOT BE SUBSTITUTED. MANUFACTURED BY FRY REGLET CORPORATION. U
<br /> ALUMINUM WINDOWS LL_
<br /> AND GLAZING 1 4.FINISH INTERIOR SURFACES, AS SCHEDULED ON DRAWINGS, EXCEPT AS MODIFIED AND SUP- 4.- LATH ANCHORAGES :
<br /> PLEMENTED HEREINAFTER AND UPON WRITTEN OWNER APPROVAL. IN GENERAL, USE EGGSHELL a.- ANCHORAGES AT METAL FRAMING : ASTM C954, SELF-DRILLING AND U
<br /> I .- ALUMINUM WINDOWS: PROVIDE ALL LABOR, MATERIALS, EQUIPMENT, SHEEN FOR WALL BOARD SURFACES; SEMI-GLOSS FOR HOLLOW METAL AND WOOD TRIM; SELF TAPPING SCREWS FOR HEAVY GAUGE STEEL FRAMING AND ASTM
<br /> AND ENGINEERING REQUIRED FOR THE COMPLETE INSTALLATION OF I .- PROVIDE GLASS AND GLAZING THAT HAS BEEN PRODUCED, AND FLAT FOR DUCTWORK. C 1002, SELF DRILLING AND SELF TAPPING SCREWS FOR LIGHT GAUGE W
<br /> METAL WINDOW AND FRAME SYSTEMS WITH INTEGRAL AIR AND VAPORn-
<br /> BARRIERS, INCLUDING CLIPS, ANCHORS, VINYL GLAZING BEADS, AND FABRICATED AND INSTALLED TO WITHSTAND NORMAL TEMPERATURE PANTING SCHEDULE - EXTERIOR SURFACES STEEL FRAMING. INSTALL GALVANIZED #8 WAFER HEAD SCREWS AT 6
<br /> CHANGES, WIND LOADING, IMPACT LOADING ( WHERE APPLICABLE ) , INCHES ON CENTER VERTICALLY AT EACH STUD.
<br /> OTHER ACCESSORIES. DESIGN AND SIZE COMPONENTS IN ACCORDANCE WITHOUT FAILURE INCLUDING LOSS OR BREAKAGE OF GLASS, FAILURE OF A.- FERRUS METAL : I ST. COAT- ALKYD FLAT PRIMER; 2 ND. AND 3 RD.
<br /> WITH CBC CODE EXPOSURE "B" AND WIND SPEED OF 70 MPH AND IN SEALANTS OR GASKETS TO REMAIN WATER TIGHT, DETERIORATION OF COATS- 100 PERCENT ACRYLIC SEMI-GLOSS. 5.- CEMENT PLASTER MIXES
<br /> ACCORDANCE WITH ANSI/ASTM E283 AND E330. GLASS AND GLAZING MATERIALS, AND OTHER DEFECTS IN THE WORK. a.- SCRATCH COAT PROPORTION : ONE PART PORTLAND CEMENT,
<br /> COMPLY WITH RECOMMENDATIONS OF FLAT GLASS MARKETING D. FERRUS METAL : IST. COAT - EPDXY FLAT PRIMER; 2ND. AND 3RD. FOUR PARTS AGGREGATE AND 3 OUNCES PRF ADMIXTURE.
<br /> 2.- WINDOWS SHALL BE ALUMINUM, DUO-PAYNE SLIDING AS ASSOCIATION ( FGMA ) "GLAZING MANUAL " AND " SEALANT MANUAL " COATS - ALIPHATIC URETHANE GLOSS EMANEL. b.- BROWN COAT PROPORTIONS : ONE PART PORTLAND CEMENT, FIVE
<br /> MANUFACTURED BY BLOMBURG WINDOW SYSTEMS OR APPROVED EQUAL. EXCEPT WHERE MORE STRINGENT REQUIREMENTS ARE INDICATED. PARTS AGGREGATE AND 3 OUNCES PRF ADMIXTURE.
<br /> COLOR : BRONZE OR AS SELECTED BY THE ARCHITECT FROM C.- GALVANIZED METAL AND ALUMINUM : I ST. COAT - ETCH PREP; 2 ND.
<br /> MANUFACTURES STANDARD COLORS. COMPLY WITH CBC CHAPTER 24. SAFETY GLAZING SHALL BE IN COAT- ACRYLIC FLAT PRIMER ; 3 RD. AND 4 TH. COATS - 100 PERCENT
<br /> COMPLIANCE WITH ANSI Z97. 1 CURTAIN WALL AND WINDOW GLASS SHALL G.- INSTALL METAL PLASTER BASES AND ACCESSORIES IN CONFORMANCE
<br /> 3.- FRAME AND SASH MEMBERS SHALL BE EXTRUDED ALUMINUM ALLOY COMPLY WITH ASTM C 1 048 FALL OUT PROTECTION. ALL GLASS SHALL ACRYLIC SEMI-GGLOSS. WITH ASTM C I OG3. INSTALL LATH AS SPECIFIED IN SECTION 25 10 AND
<br /> GOG3-T5. COMPONENTS AND ACCESSORIES SHALL BE DOUBLE-RATED CONFORM TO FEDERAL SPECIFICATION DD-G-45 I c. MANUFACTURER'S TABLE 2507.2 OF THE CBC. LATH SHALL STAND OFF SUBSTRATE
<br /> STEEL, STAINLESS STEEL, ALUMINUM OR OTHER CORROSION RESISTANT LABELS, SHOWING STRENGTH, GRADE, THICKNESS, TYPE, AND QUALITY D.- CONCRETE : I ST. COAT - ACRYLIC FLAT PRIMER ; 2 ND. AND 3 RD. IMMEDIATELY BEHIND THE LATH A MINIMUM OF I / 4 INCH. PLACE CASING
<br /> MATERIAL. ALL OPERABLE UNITS SHALL HAVE REMOVABLE SCREENS. WILL BE REQUIRED ON EACH PIECE OF GLASS. LABELS SHALL REMAIN ON COATS- ELECTROMETRIC FLAT. BEADS AT TERMINATIONS OF PLASTER FINISH. INSTALL ACCESSORIES TO
<br /> SCREENS SHALL BE ALUMINUM WIRE 18 X I G MESH COATED WITH GLASS UNTIL IT HAS BEEN SET, INSPECTED AND APPROVED. LINES AND LEVELS. BEGINNING INSTALLATION MEANS ACCEPTANCE OF O
<br /> CHARCOAL COLOR FLAT ENAMEL FINISH AND FRAMES SHALL MATCH EXISTING CONDITIONS. ,� /
<br /> WINDOW FRAME COLOR. WINDOW SYSTEMS SHALL BE SET IN THE PROPER 2,- TEMPERED GLASS SHALL BE PPG " HECULITE " , OR EQUAL, I / 4 INCH PANTING SCh EDU LE - INTERIOR SU REACES 7.- APPLY PLASTER SCRATCH COAT AND BROW COAT TO A NOMINAL f�
<br /> LOCATIONS AND SHALL BE SQUARE, PLUMB, LEVEL, AND JOINED TO EACH THICK FOR INSTALLATION IN OR ADJACENT TO DOORS. w > O
<br /> OTHER AND INSTALLED IN STRICT ACCORDANCE WITH MANUFACTURER'S THICKNESS OF 3 / 8 INCH EACH. INSTALL FINISH COAT TO A NOMINAL cz
<br /> INSTRUCTIONS. INSULATE ALL ALUMINUM WORK FROM CONTACT WITH 3.- HEAVY SHEET GLASS SHALL BE NEW, CLEAR I / 4 INCH THICK AS THICKNESS OF I / 4 INCH. MOIST CURE BROW COAT FOR A MINIMUM OF 0 W . N
<br /> REQUIRED BY CODE FOR SIZE OF OPENING OR AS NOTED ON DRAWINGS, A.- GYPSUM BOARD : I ST. COAT - PVA PRIMER SEALER ; TEXTURE BY
<br /> PLASTER AND / OR CONCRETE. ALL POSSIBLE SOURCES OF AIR OR WATER SEVEN DAYS BEFORE APPLYING FINISH COAT. THE MAXIMUM VARIATION = J �
<br /> TYPE II, "A" QUALITY, OF GLAZING QUALITY, FREE FROM DEFECTS, AS GYPSUM BOARD CONTRACTOR ; 2 ND. COAT PVA PRIMER SEALER ; 3 RD. w
<br /> FROM TRUE FLATNESS IS 1 / 8 INCH IN 5 FEET. v
<br /> LEAKS SHALL BE THOROUGHLY SEALED. THE USE OF ALL CAULKING AND AND 4TH. COATS - WATERBORNE SEMI-GLOSS EPDXY PAINT. z U �
<br /> SEALING COMPOUNDS SHALL BE IN STRICT ACCORDANCE WITH THE MANUFACTURED BY PPG Co. , OR APPROVED EQUAL. 8.- SURFACES TO RECEIVE ACRYLIC FINISHES MUST BE STRUCTURALLY w w U
<br /> MANUFACTURER'S PRINTED RECOMMENDATIONS. B.- GYPSUM BOARD I ST. COAT - PVA PRIMER SEALER ; TEXTURE BY SOUND, CLEAN AND DRY. CONCRETE MASONRY AND CEMENT PLASTER � z
<br /> 4.- INSULATED GLASS UNITS, CLEAR AND SPANDREL, SHALL BE I INCH, BASE COATS MUST BE PROPERLY CURED AND FREE OF ALL GREASE,
<br /> INSULATED UNITS WITH LOF " ECLIPSE " I / 4 INCH GLAZING. BRONZE WITH GYPSUM BOARD CONTRACTOR ; 2 ND. PVA PRIMER SEALER ; 3 KD. AND 4 z z l� O
<br /> 4.- ALL WINDOW FRAMES SHALL BE ACCURATELY MORTISED, CUT AND TH. COATS - LATEX EGGSHELL ENAMEL. MILDEW, FUNGUS, EFFLORESCENCE AND ANY OTHER CONTAMINANT O
<br /> REINFORCED FOR HARDWARE AS SPECIFIED BY MANUFACTURER. SILVER REFLECTIVE COATING ON FACE AND CLEAR FLOAT GLASS AT BEFORE INSTALLATION OF FINISH. v
<br /> INTERIOR FACE UNLESS OTHERWISE NOTED. SPANDRAL UNITS SHALL BE > U
<br /> FITTED " GLASS WITH COATING ON #2 SURFACE. GLAZING SYSTEM SHALL C.- METAL : I ST. COAT - ALKYD FLAT PRIMER ; 2 ND. AND 3 RD. COATS - 9.- REFER TO MANUFACTURER'S INSTRUCTIONS FOR APPLICATION OF z O
<br /> AC ALL GLAZING SHALL BE DONE BY SKILLED GLAZERS AND IN BE " DRY " GASKET SYSTEM WITH NO WET SEALANTS. LATEX SEMI-GLOSS ENAMEL. LEVELER, PRIMER AND ACRYLIC FINISH. �c j
<br /> ACCORDANCE WITH THE BEST STANDARD PRACTICE. GLASS SHALL BE
<br /> SET TIGHT AND TRUE IN CLEAN, DRY SASH. PROVIDE CLIPS, BLOCKS, AND :D.- CONCRETE I ST. COAT - ACRYLIC FLAT PRIMER ; 2 ND. AND 3 RD. 10.- THE FINISH COAT SHALL BE APPLIED AND TEXTURED CONTINUALLY
<br /> SHIMS AS REQUIRED. 5.- WIRE GLASS SHALL BE NEW, CLEAR, POLISHED, WITH WIRE MESH I / 4 I.L.I
<br /> INCH THICK. ALL WIRE GLASS FOR OPENINGS IN FIRE-RATED PARTITIONS, COATS - LATEX SEMI-GLOSS ENAMEL. OVER THE WALL SURFACE IN ORDER TO MAINTAIN A WET EDGE AND
<br /> WALLS OR DOORS, SHALL BE UL APPROVED AND BEAR THE LABEL PROVIDE A UNIFORM APPEARANCE.
<br /> 6.- THE CONTRACTOR SHALL BE RESPONSIBLE FOR PROTECTING
<br /> EXPOSED SURFACES FROM DAMAGE AND FINAL CLEANING ALUMINUM STATING MATERIALS COMPLY WITH NEPA 80 AND ANSI. E.- MASONRY (CMU) : I ST. COAT - ACRYLIC BLOCK FILLER PRIMER ; 2 ND. GYPSUM WALL BOARD
<br /> AND 3 RD. COATS - LATEX SEMI-GLOSS ENAMEL.
<br /> AND GLAZING. I. PROVIDE GYPSUM WALL PANELS MANUFACTURED IN ACCORDANCE WITH REQUIREMENTS OF
<br /> F.- GALVANIZED METAL , ZINC ALLOY METAL AND ALUMINUM : I ST. COAT ASTM 33G.
<br /> ETCH-PREP. : 2 ND. COAT - ACRYLIC FLAT PRIMER ; 3 RD. AND 4 TH. COATS 2. PROVIDE METAL EDGE AND CORNER BEADS AT ENDS, EDGES AND CORNERS.
<br /> EI N ISH HARDWARE LATEX SEMI-GLOSS ENAMEL 3. WATER RESISTANT GYPSUM WALL BOARD SHALL BE 5/8"THICK TAPERED AND ROUNDED EDGES DATE
<br /> I .- DOOR TYPE A EDGE5 AND SHALL BE INSTALLED IN ALL WET AREAS AS INDICATED ON DRAWINGS. 05/22/20
<br /> 4 IN ACCORDANCE
<br /> IOTHERWISE
<br /> OR
<br /> 2.- DOOR TYPE B PROVIDE TYPE'S' BUGE HEAD SCREWS FOR ATTACHMENT OF BOARDTO METAL AMDNGATED,
<br /> 3.- DOOR TYPE C AND TYPE'S' PAN HEAD SCREWS FOR ATTACHMENT OF FRAMING TO DOOR FRAMES. SCALE
<br /> 4.- ACCEPTABLE MANUFACTURER'S OR APPROVED EQUAL: 5. PROVIDE ALL INCIDENTAL AND ACCESSORY MATERIALS,TOOLS, EQUIPMENT, AND METHODS REQUIRED
<br /> FOR SATISFACTORY COMPLETION OF GYPSUM WALL BOARD CONSTRUCTION INCLUDING ACCESS DOORS
<br /> AND PANELS.
<br /> G. APPLY CONTINUOUS BEAD SEALANT AT ALL JOINTS OF WALL BOARD ABUTTING ADJACENT DRAWN
<br /> CONSTRUCTION, INCLUDING AROUND FRAMED OPENINGS AND OTHER PROTRUSIONS THROUGH M.BARRETO
<br /> WALL BOARD WHERE SEALANT 15 EXPOSED. PROVIDE POLY-SULFIDE SEALANT; WHERE UNEXPOSED.
<br /> PROVIDE ACOUSTIC SEALANT.
<br /> 7. APPLY PRE-FILL COMPOUND TO JOINTS IN ACCORDANCE WITH INDUSTRY STANDARDS. APPLY JOB
<br /> EMBEDDING COMPOUND REINFORCING TAPE CENTERED OVER JOINT; APPLY SKIM COAT. AFTER TAPING
<br /> AND EMBEDDING COMPOUND IS DRY, APPLY SECOND COAT FILLING AND TAPER FLUSH WITH SURFACE;
<br /> FIRE TAPE PENETRATIONS AT DEMISING WALLS, CORRIDOR ENVELOPE AND OTHER RATED ASSEMBLIES.
<br /> 8. PROVIDE FINAL FINISH THAT IS SMOOTH, WITHOUT DIVOTS, BUMPS, BOWS OR ANY OTHER SURFACE SHEET
<br /> BLEMISH, READY TO RECEIVE PAINT.
<br /> 9. CUSTOM SKIP TROWELED FINISH WHERE SPECIFIED ON PLANS. COORDINATE FINISH
<br /> WITH ARCHITECT.
<br /> A- 3 ,0
<br />
|