|
OPV! 42' OIA MULTI-PORIDUAL POINT FILL 4' MIN. 70 39 40 4' VAPOR RECOVERY ADAPTER CAP IN SPILL
<br /> 26 &CONTAINMENT FILL BOX. PER A EVR VR-102,
<br /> SPILL CONTAINMENT ASSEMBLY W/ (2) 5 GALLON TOP OF SPILL NO DRAIN VALVE TO BE INSTALLED ON VAPOR
<br /> SPILL BUCKETS CARD STAGE I EVR COMPLWNT 10 BUCKET RECOVERY SPILL BUCKET. (IYP.)
<br /> PER VR-102, AND ADJUSTABLE FLARED SKIRT 18" MANHOLE O p PLASTIC GAP SUPPLED BY BP DESIGN
<br /> 4" FILL ADAPTER AND CAP IN SP
<br /> RL 37 38 5 GALLON SPILL CONTAINER.
<br /> CONTAINMENT FILL BOX 0YP.) (INUNE DRAIN ON FILL BUCKET ONLY) J-BOX (TYP. 8 7 2 3 4 Architectural
<br /> WATERTIGHT SUMP SHIELD 34 18 42' 1 2 3 4 14 THICKENED CONCRETE
<br /> Solutions Group
<br /> BOOT AND CLAMPS SLAB (rM,)
<br /> MINI HYDROSTATIC
<br /> SUMP S SOR 1 _455 Bemet I Valley Rd. Stile A-102
<br /> (LAE Santa Rosa, CA. 95461
<br /> DEPT1s _ JJ
<br /> • e
<br /> IN, 12' vii P��FlE� 7 6 9
<br /> MAR•) f 4" FRP ANNULAR
<br /> PFA GRAVEL 6 _ - I SEAL OFF 1 RISER EDAR
<br /> BACKFILL(IYPJ 6' WIDE DETECTABLE UNDERGROUND Eg F,?5 Cti?F
<br /> 2-IN-1 SENSOR BOX 1 MARKING TAPE 8 6 Q
<br /> EMPIRE MAGNATEC 132-143 ¢-
<br /> JUNGFION BOX 788 22 4• CAV. STEEL RISERS STAGE I VAPOR6 8 TO TURBINE _
<br /> SEE STATIC GROUNDING DETAILS RISER IS IN SAME PLANE AS TANK LEVEL SUMP REIN. I /31/19
<br /> HOME RUN
<br /> ON SHEET G.0.7.2 M?,) 9 GAUGE IN THIS VIEW
<br /> JDOUBLE WALL SUMP
<br /> 14 STRANDED BARE CU CONTRACTOR TO INSTALL CLEVIS 17 6 2" FIBERGLASS 4 WALL sr, 2P
<br /> GROUND WIRE TO OTHER AND COTTER PIN BRINE RESERVOIR TO FILL SUMP NIPPLE D.W. RIGID SUMP rEOFCAIIFOR\
<br /> TANKS M?,) TANK GAUGE ADAPTER 2" FIBERGLASS 6 PENETRATION FITTING Seat
<br /> /4 STRANDED BARE CU 0 & up HYDROSTATIC O END CAP 2 2
<br /> GROUND WIRE TO VEEDER ROOT ,1 GPH EIAGNOSTRICTNE SENSOR
<br /> GROUND ROD (TW,) 04 O PROBE TANK LEVEL PROBE W/ TLS CAP _ p
<br /> 1 " FRP BONDED ENTITY FITTING 8 124 & RING. OVERFILL ALARM SEI O 90%
<br /> (Type) CAPACITY, USE a FLOAT IN INSTALL KD
<br /> 1 " MONITORING CONDUIT 1/4' VACUUM
<br /> (ROUTED TO INTERSTITIAL) 5 18 2' INSIDE 3" DOUBLE
<br /> (ROBROY THROUGH SUMP ONLY) TUBING
<br /> 42" DOUBLE WALL POLYGON SUMP 4 4 3" OVER 2' FIBERGLASS DRILL AND TAP CPP WAIL OVERGVSS
<br /> BODY (e) FLAT PANELS CROSSOVER CONTAINS VACUUM 1/2' NATER-TIGHT FOR 1/2' CORD GRIP, CROSSOVER PIPE FOR
<br /> TUBING ONLY TO VAC SENSOR ELECTRICAL CORD (APPLY PIPE SEALANT VACUUM TIDING
<br /> ASSEMBLY GRIPS (RATED FOR AS NEEDED) q q
<br /> SUMP MONITOR LIQUID SENSOR / H 2 2 3" D,W. FRP BONDED ENTRY FIRTING FUEL COMPATIBILITY)
<br /> MOUNTED N HOLDER 53.14 & 4"x3' CONCENTRIC REDUCER W/
<br /> TEST PORT & PLUG
<br /> OVERFILL PROTECTION DROP
<br /> TUBE SET AT 95% 41 t 19 EXTRACTOR FITTING 4'x4k3'x2'
<br /> (TYP.)
<br /> SUMP TEST PLUG (TYP,) G: ELEVATION - INTERSTITIAL SPACE MONITOR H : VACUUM TUBE AT SUMP ENTRY DETAIL
<br /> SCALE: 3/4" = 1'-0" SCALE: 3/4" = 1 -a'
<br /> A: NOT USED D: SECTION VIEW - FILL SIDE SUMP (SINGLE FILL W/O MANWAY )
<br /> SCALE HIS
<br /> SCALE: 3/+m = 1'-0'
<br /> SUMP MONITOR UOUIO SENSORH ® - NOTES k m m rn
<br /> MOUNTED IN HOLDER 0 14 m zo z
<br /> B" ACCESS PORT O z
<br /> INSTALL TANK ID MARKERS IN THE SPILL CONTAINMENT HOLES. COVERS
<br /> 4" D.W. FRP BONDED ENTRY FITTING Z 2 8' a WEBER ROOT A GPH MAGNOSTRICIIVE O SLOPE CONCRETE AWAY FROM ALL MANHOLES 1 ' RISE OVER 12' RUN � SHALL BE PRIMED AND PAINTED ACCORDING TO SPECIFICATIONS. F^ 5 v �a
<br /> & 5k4' CONCENTRIC REDUCER WJ g 15 04 0 0 PROBE TANK LEVET. PROBE W/ TLS CAP z ti ¢ w
<br /> TEST PORT & 1/4' PLUG. VACUUM In rn & RING OVERFILL ALARM SET O 90% O FIBER REINFORCEMENT TO BE USED. PRE-MIX UNIFORMLY THROUGHOUT SECONDARY CONTAINMENT IS REWIRED FOR ALL PENT AND STAGE II O a m m
<br /> SENSOR ASSEMBLY LOCATED AT 20K a CAPACITY. USE 4" FLOAT IN INSTALL KIT CONCRETE, VAPOR RECOVERY PIPING. a o y o N o
<br /> OR 30K TANK. zi " m
<br /> 3" OVER 2' FIBERGLASS CROSSOVER ® s 0 z
<br /> 3' INSIDE 4' O.W. F.G. VACUUM m a 4 4 CONTAINS VACUUM TUBING ONLY TO O REINFORCING BARS TO BE NO LESS THAN Y AND NO MORE THAN NOT USED ? u z o 0
<br /> MONITORED VAPOR RECOVERY VAC SENSOR ASSEMBLY 4" FROM SURFACE. 0 9 z o of m m
<br /> LAYOUT TANKS & STAGE II VAPOR RECOVERY PIPING SUCH THAT THE STAGE < G_ o
<br /> 1 1 5 0 3' D.W. FRP BONDED ENTRY FETING O REINFORCE CONCRETE SLAB MOUND MANHOLE WITH 4-13 REBAR 60" 3 <
<br /> 2 2 4 II PIPING DRAINS & ENTERS INTO REGULAR UNLEADED TANK FIRST W/ 3"
<br /> & 4"x3' CONCENTRIC REDUCER W/ LENGTH. PLACE REBAR 6" FROM SIDES OF BO%. 1_
<br /> 3' BELL X MICE ADAPTER (TYP.) 5 TEST PORT & PLUG CONNECTIONS, AND CONTINUES 3' TO OTHER TANKS. m < < ¢ a as
<br /> ONE t ' STANDARD MONITORWG HOMERUN CONDUIT TO EACH TANK. F h
<br /> 6 2" CAP, DRILL HOLES IN END AN FOR STANDARD MONITORING DEVICES, LOOP CONTAINMENT SUMP CONCRETE SHALL BE THICKENED AT THE THE FILL SUMPS DOWN TO m V N
<br /> INSTALL GROMMETS FOR TUBING SENSORS, PUD, VAC SENSORS & TANK GAUGE TO TANK INTERSTITIAL BELOW THE TOP OF CONTAINMENT OF THE DOUBLE WALL SUMP AS m _ m m
<br /> 2'%18' FMD( CONNECTOR 1 7 O SENSOR LOCATION AND HOMERUN TO BLDG. PROVIDE SEAL-OFFS IN REWIRED, DIMENSION OF SLAB THICKNESS VARIES WITH SITE CONDfiIDNS, u, m
<br /> TANK
<br /> PASS THROUGH BUILDING & PRIOR TO LEAVING HAZARDOUS AREA. ROUTE TO a " o m n N n
<br /> 4" VAPOR RECOVERY ADAPTER & CAP IN SPILL O m
<br /> INTRINSICALLY SAFE TROUGH IN BUILDING. CONDUITS SHALL CONTAIN m m
<br /> 4' FILL ADAPTER AND CAP W SPILL 39 40 CONTAINMENT FILL BOX. PER CMB EVR VR-102 2 ONLY LOW VOLTAGE WIPING FOR SENSORS. ALL CONDUIT PENETRATIONS CROSSING FLOC CONNECTORS MUST MAINTAIN A MINIMUM OF 2 INCH o 0
<br /> 37 38 NO DRAIN VALVE TO BE INSTALLED ON VAPOR MUST BE MADE WITH ROBROY PVC COATED CONDUIT ONLY. � CLEARANCE OR THE USE OF AN ARD CHAFING DEVICE MUST BE INSTALLED,
<br /> CONTAINMENT FILL BOX RECOVERY SPILL BUCKET
<br /> ALL MANHOLE ACCESS COVERS TO BELOW GRADE O PFA GRAVEL BACKFILL ALL SUBSITFUTE5 MUST BE APPROVED BY OVEEF OW OVERFLOWPREVENTION PROTECTI : USE OVERFLOW
<br /> DROP CO FLAPPER IVALVE SEEACHIEVED ABY
<br /> 2' BELL K MALE ADAPTER
<br /> nYP•) 4 SHALL BE LIQUID TIGHT AND LOCKABLE MANUFACTURER AND OWNER'S FIELD REPRESENTATIVE.
<br /> 0 095% AND IS IN ACCORDANCE WITH FEDERAL AND STATE GUIDELINES
<br /> 2" INSIDE 3' DVN F.G. VACUUM �'.�; 42" DA MULTI-PORT SINGLE DUAL POINT PIPING SHALL BE WD AND CONTINUOUSLY SUPPORTED ON A 6" FOR UST OVERFILL REQUIREMENTS,
<br /> MONITORED VENT UNE 2B FILL SPILL CONTAINMENT ASSEMBLY W/ (2) OCOMPACTED PEA GRAVEL BEDDING, PIPING SHALLNOT DU
<br /> 5 GALLON SPILL BUCKETS CARD STAGE I SUPPORTED BY BLOCKS, PLANKS, OR OTHER DEBRIS,
<br /> AN OVERFILL ALARM AND ACKNOWLEDGE SWITCH TIED INTO THE VETOER
<br /> 000 EVR COMPLIANT PER VR-702 ROOT AUTOMATIC TANK GAUGE SYSTEM. THE MONITORING SYSTEM
<br /> OND PLATE 2" DIA BRINE MONITORED DOABLE WALL O NS ELATION TO BE PERPENDICULAR TO CONTAINMENT SUMP, OFFLINE PROTIDES AN AUDIBLE AND VISUAL HARM WHEN THE TANK(S) ARE
<br /> 3' D.W. FITTI
<br /> RP BONDED ENTRY FNG & 2 2 CONTAINMENT SUMP (TYP.) INSTALLATION NOT PERMTITED, FILLED TO THE 909 LEVE,
<br /> 4"x3' CONCENTRIC REDUCER W/ TEST O REMAIL RISERS FOR FULL PIPE BORE IF REGUIRED,
<br /> PORT & VACUUM TUBING ROUTED TO 7 1 30X18" R-EX CONNECTOR Nom: CONIRACIOR 70 USE UIRED O Q
<br /> GALVANIZED DS NKS LE REWIRED C
<br /> VAC SENSOR MINIMIZE BENDS IN FLE7(IBIE CONNECTORS
<br /> B : NOT USED E: PLAN VIEW - FILL SIDE SUMP (SINGLE FILL W/O MANWAY) xx HOTEL INDICATES ITEMS FOUND ON MATERIALS UST SHEETS 14.5.3,01 Q
<br /> SCALE: HIS SCALE: 3/4" = IN-W 02 C3Q
<br /> LF5
<br /> 43 1/4" Opening O.D. O
<br /> INSTALL CSI SUPPLED SHROUD MSINGLE Q
<br /> ADAPTER BONDED TO SUMP ADHESIVE
<br /> CHANNEL FOR INTERFACE TO DPW 38-1/B' O.D. (QUAD FILL)
<br /> API COLOR-SYMBOL SYSTEM FOR PRODUCT IDENTIFICATION
<br /> ry WATER TIGHT SUMP SHIED (SEE SUPP ABOVE UNLEADED ETHANOL r cRos UJ Q
<br /> DETAIL AGN R REED Cesar, MTH " ACCESS PORT W U
<br /> S
<br /> HYDROSTATIFACTOC RESERVOIR C�vnr © mcxcuo¢ � HNC SAGE IFILLFORT
<br /> MFA To REMAIN
<br /> 38' Opening I.D. m L
<br /> FACTORY BONDED I rNRE C� UAE NWTE Gross ON
<br /> a ON BONE \ wowt cxxuE ® � Wlar, M11N REDG/EXf VAPOR GREY OR WHITEOz_ o aRaE \ NHIfE INIC 0JOINT (IYP.) SUP ON RISER '� w O
<br /> BLACK GROSS ON
<br /> d . SUP ON POSER 42' LD• -� m FlETD SEALED JOINT. rn B ON
<br /> ,KyIV r. WITH
<br /> Q N
<br /> FIELD SEEMED JOINT. •1 z0 (ADHESIVE SUPPLED DW POLYGON BODY < CDar LOW GRADE
<br /> (ADHESIVE SUPPLIED DW POLYGON BODY �+ W/ KIT) . it 4 (OPTIONAL)
<br /> :zwW/ <t w Im•A6roH/H 4"x4" EGGHKAY
<br /> YDlfAF TrpEN (N REFLECTOR RAJWR
<br /> ri ,I HE(AGON � FDR PRODUCT
<br /> i 3/8 X 1/4 55 �.. U SRGE I VAPOR ftECO/EN1• IDENTFIVCOLORED PER.
<br /> 3/e X 1/4 SS BUSHING EaACK >M �� a �
<br /> FILE PORE S<AlD1EDADA�EPDXY
<br /> NG 4 1INSTALLED ATa LETTERS BONE STRIPE ON
<br /> 8
<br /> INSTBUSHALLED AT DW HEXAGON MOUNTED INSTALLED
<br /> FACTORY t . j gpNz� �i BY CONLRACIIXR.
<br /> & FACTORY 1 t •� eAcxatouND CONSIRlIC110N AND"1 E85 awICE ORar (CHECK WITH
<br /> FACTORf �A PFaect Number
<br /> FAcmm. LAY-UP DINCOLLAR
<br /> TO EAD UNINTIENA 'RDNftITE FEWEMAI SPA16002 . 0
<br /> LAY-UP IF ANNKED TO \ IT A � POFHPtr SOWRE THIS AREA HI REMAIN
<br /> DW COLLAR I E�� Mho GREY OR WHITE Sheet Name
<br /> BONDED TO 8" ACCESS PORT TO BE
<br /> %I LJOINT DETAILS 2 REF. API 1637 - PRODUCT SYMBOLS ORIENTATED TO THE SAME
<br /> JOINT DETAILS NOTE TUE ABOVE SARIDS REPRESDIr WDIJUM amDnNESS SIDE AS TANK LEVEL
<br /> x 2 FOR PRODUCT gD11ENATION. CONSULT LOCAL DSHMAION GAUGE
<br /> a OCONTRACTOR TO ADDITONALLY GLASS WRAP & LAMINATE AT CONNECTION FOLLOWING CURING OF 4z" DLA. POLYGON SUMP BODY RkNAGM FOR Ualh. METHOD DF FRODx,T MENDNaTION TO FILLSIDESUMP
<br /> ADHESIVE, SPECIFIC ATTENTION MUST BE GIVEN TO SURFACE PREP AS TESTING REQUIREMENTS (B) 17 3/8' FLAT PANELS BE USED. AN STANDARD COLORS INSTALLATION DETAILS
<br /> 1 CONTRACTOR TO ADDITIONALLY GLASS WRAP & LAMINATE AT CONNECTION FOLLOWING CURING OF 4Y WA POLYGON SUMP BODY WILL DEFECT THE SMALLEST OF FLAWS. ALL MATERIALS MUST BE COMPATIBLE WITH GASOUNF, UNLEADED PREMUM - RED
<br /> o OAOHESNE. SPECIFIC ATTENTION MUST BE GIVEN TO SURFACE PREP AS TESTING REQUIREMENTS (e) 17 3/8' FIAT PANELS OPWVR-102WIO MANWAY)
<br /> b WALL DEFECT THE SMALLEST OF FLAWS, ALL MATERIALS MUST BE COMPATIBLE WITH GASOLINE, GASOLINE WITH 15X MTBE (METHYL TE TIPRY-BUTYL ETHER), OR GASOLINE WITH LOX ETCH �FACTORY
<br /> BUSHING.STALLED EDU PLUS _ (DOUBLE WALL VENTNYAPOR)
<br /> o GASOLINE WITH 15% MTBE (METHYL. D]RLARY-BUTYL ETHER), OR GASOLINE WITH 10% EtOH 1/4" DRAIN/TEST BUSHING. (ETHANOL). FIBERGLASS AND RESIN MUST EXTEND 1/2" BEYOND COVERAGE OF ADHESIVE.
<br /> 7
<br /> (ETHANOL), FIBERGLASS AND RESIN MUST EXTEND 1/2' BEYOND COVERAGE OF ADHESIVE. NOTE FACTOR( INSTPIIED O THE STRAP CHANNEL IF PRESENT ON THE FILL SIDE SUMP DOES NOT "COMMUNICATE" WRH CONTRACTOR SHALL BE HELD RESPONSIBLE EXTRA LBW SULFUR DIESEL - YELLOW
<br /> G O THE STRAP CHANNEL IF PRESENT ON THE FILL SIDE SUMP D06 NOT "COMMUNICATE" WITH CONTRACTOR SHAT BE HELD RESPONSIBLE THE INSIDE OF THE SUMP. CONTRACTOR TO BE SURE TO LEAVE UNOBSTRUCTED PATH FOR FOR PROPER INSTALLATION & PREPARATION Sheet Number
<br /> ML THE INSIDE OF THE SUMP, CONTRACTOR TO BE SURE TO LEAVE UNOBSTRUCTED PATH FOR FOR PROPER INSTALLATION & PREPARATION STRAP TO PENETRATE INTO THE CHANNEL 50 THAT TANKS MAY BE PROPERLY ANCHORED. PER MANUFACTURERS INSTRUCTIONS AND
<br /> SHALL REINSTALL SUMPS IF HYDROSTATIC ACCESS COVER IDENTIFICATION M .. 53 .. 17
<br /> STRAP TO PENETRATE INTO THE CHANNEL SO THAT TANKS MAY BE PROPERLY ANCHORED, PER MANUFACTURERS INSTRUCTIONS AND TESTING SHOWS LEAPING IN THIS AREA C STANDARD API COLOR AND
<br /> i SSHALL REINSTALL
<br /> LEAKING IN MISAREAof F: DOUBLE WALL FILL SUMP RISER THE SUMP. IDENTIFICATION SYMBOLS SCALE, NONE STANDARD TWO POINT FILL SCALE NONE
<br /> C : DOUBLE WALL FILL SUMP RISER TEE SUMS. SCALE: 3/40 = 1 '-0"
<br /> j SCALE, 3/4" = 1'-0"
<br />
|